M-system R3Y-SS8 Bedienungsanleitung

R3Y-SS8

P. 1 / 3 EM-8958 Rev.3

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

DC current input module ........................................... (1)

■ MODEL NO.

Check that model No. described on the specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

INSTRUCTION MANUAL

MODEL R3Y-SS8

DC CURRENT INPUT MODULE

(8 points, isolated)

POINTS OF CAUTION

■ CONFORMITY WITH EC DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

figurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated in

a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■ HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other modules

on the same backplane. It is possible to replace them without

removing the power supply. However, replacing multiple

modules at once may greatly change line voltage levels. We

recommend that you replace them one by one.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufficient ventila-

tion.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ UNUSED INPUT CHANNELS

Set the unused channels to -20 – +20mA or 0 – 20mA range.

Otherwise, set them as "Unused" with PC Configurator

software: R3CON. Unused channels left open with 4 – 20mA

setting are equal to the input lower than -15%, which sets a

data abnormality at the PLC or the host device.

■ AND ....

The unit is designed to function as soon as power is supplied,

however, a warm up for 10 minutes is required for satisfying

complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3Y-SS8

P. 2 / 3 EM-8958 Rev.3

COMPONENT IDENTIFICATION

•Conversion Rate: SW3

SW CONVERSION RATE

160 ms (*)80 ms 40 ms 20 ms

SW3-1 OFF ON OFF ON

SW3-2 OFF OFF ON ON

(*) Factory setting

■ FRONT VIEW■ SIDE VIEW

RUN LED

ERR LED

Input Connector

• Pin Assignment

20 A

SW2SW1

SW3

Range

Input 1-4 (SW1)

Input 5-8 (SW2)

Conv.

Rate

■ DIMENSIONS mm (inch)

TERMINAL CONNECTIONS

Connect the unit as in the diagrams below and the next page.

130 (5.12)

27.5 (1.08) 110 (4.33) POSITIONING

GUIDE

■SIDE DIP SW

•Input Range: SW1, SW2 (selectable per 4 channels)

INPUT 1 through INPUT 4 (SW1)

INPUT 5 through INPUT 8 (SW2) RANGE

1234

OFF OFF OFF OFF

4 – 20mA

(*)

ON OFF OFF OFF 0 – 20mA

OFF ON OFF OFF

-20 – +20mA

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the input circuit abnormality (AD

converter response failure);

Green in normal operating conditions.

R3Y-SS8

P. 3 / 3 EM-8958 Rev.3

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

INTERNAL POWER

BUS A

BUS B*

*For dual redundant communication.

BUS CONNECTOR

18B

17B

13B

10B

18A

14A

17A

13A

10A

–

INPUT 1 +

–

INPUT 2 +

–

INPUT 3 +

–

INPUT 4 +

–

INPUT 5 +

–

INPUT 6 +

–

INPUT 7 +

–

INPUT 8 +

14B

■ CONNECTION DIAGRAM ■ INPUT CONNECTOR (40-pin)

PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT

1A NC 1B NC

2A NC 2B NC

3A NC 3B NC

4A NC 4B NC

5A – IN8 5B – IN4

6A + IN8 6B + IN4

7A NC 7B NC

8A NC 8B NC

9A – IN7 9B – IN3

10A + IN7 10B + IN3

11A NC 11B NC

12A NC 12B NC

13A – IN6 13B – IN2

14A + IN6 14B + IN2

15A NC 15B NC

16A NC 16B NC

17A – IN5 17B – IN1

18A + IN5 18B + IN1

19A NC 19B NC

20A NC 20B NC

Andere M-system Steuereinheit Handbücher

M-system

M-system 61A Bedienungsanleitung

M-system

M-system R8-DCM16ALH Bedienungsanleitung

M-system

M-system 10DY Bedienungsanleitung

M-system

M-system R8-SVT8 Bedienungsanleitung

M-system

M-system R30BS Bedienungsanleitung

M-system

M-system R7G4HH-A-YVF4 Bedienungsanleitung

M-system

M-system R7HL-DAC15E Bedienungsanleitung

M-system

M-system R3-NP1 Bedienungsanleitung

M-system

M-system R7M-EC8A/UL Bedienungsanleitung

M-system

M-system R3-RR8 Bedienungsanleitung

M-system

M-system R7M-EA8 Bedienungsanleitung

M-system

M-system R7L-DA16-R Bedienungsanleitung

M-system

M-system R30CT4E Bedienungsanleitung

M-system

M-system R7C-EC8C Bedienungsanleitung

M-system

M-system R7D-EA8 Bedienungsanleitung

M-system

M-system R7M-EC8A Bedienungsanleitung

M-system

M-system R3-NM1 Bedienungsanleitung

M-system

M-system R7E-EA8 Bedienungsanleitung

M-system

M-system R3S-RR8 Bedienungsanleitung

M-system

M-system R7D-YS2 Bedienungsanleitung

M-system

M-system R3-PA8 Bedienungsanleitung

M-system

M-system R7M-YV2 Bedienungsanleitung

M-system

M-system R7EWTU Bedienungsanleitung

M-system

M-system R3-ND1 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung