M-system 18PP Bedienungsanleitung

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 80mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Body

Specifications

Front Cover

(Connection diagram

behind)

INSTALLATION

Use Standard Rack (model: 18BXx or 18KBXx).

PULSE ISOLATOR MODEL 18PP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1861 Rev.6 P. 1 / 3

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram behind the front cover.

■EXTERNAL DIMENSIONS unit: mm (inch)

110 (4.33 )

93 (3.66)

24 (.94)

7 (.28)

78 (3.07)32 (1.26)

8–M3.5

SCREW

7 (.28)

2–M3

SCREW

■CONNECTION DIAGRAM

–

INPUT

SENSOR EXCITATION

–

OUTPUT 2

POWER

OUTPUT 1

OUTPUT 2

CONNECTOR

■TERMINAL ASSIGNMENTS

18PP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1861 Rev.6 P. 2 / 3

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

JUMPER SETTINGS

4 kΩ is attached for open collector and mechanical contact

input, while 200 Ω, 510 Ω or 1 kΩ is attached for two-wire

current pulse input.

Resistance can be changed by modifying jumper combina-

tions as shown in the table below.

Jumper settings

INPUT J1 J2 J3 J4 J5 J6

1: Mechanical contact 2 - 3 2 - 3 2 - 3 1 - 2 1 - 2 1 - 2*

2: Open collector 2 - 3 2 - 3 2 - 3 1 - 2 1 - 2 2 - 3

3: Voltage pulse 2 - 3 2 - 3 2 - 3 2 - 3 2 - 3 2 - 3

4: Two-wire current

pulse (200 Ω) 1 - 2 2 - 3 2 - 3 2 - 3 2 - 3 2 - 3

5: Two-wire current

pulse (510 Ω) 2 - 3 1 - 2 2 - 3 2 - 3 2 - 3 2 - 3

6: Two-wire current

pulse (1 kΩ) 2 - 3 2 - 3 1 - 2 2 - 3 2 - 3 2 - 3

* Close 2 - 3 for turning the ﬁlter off.

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage supplied to the rack

(model: 18BXx or 18KBXx). For the DC power source, be

sure that the ripple level is within 10% p-p.

3) Input: For the mechanical contact input, check that the

input frequency is 5 Hz or less and the pulse width is 20

msec. or more.

For the open collector input, check that the input fre-

quency is 10 kHz or less and the pulse width is 20 μsec.

or more.

For the voltage pulse input or two-wire current pulse in-

put, be sure that the input signal is as shown in the table

below.

• Waveform requirements

Square Waveform

FREQUENCY RANGE

AMPLITUDE

PULSE WIDTH & DUTY RATIO

0 to 10 kHz 1 to 3V p-p Duty 50 ±10%

0 to 10 kHz Min. 3V p-p Min. 60 μsec.*

* When the frequency is 6 kHz or more, the pulse width is 30

μsec. or more.

Sine or similar waveform

FREQUENCY RANGE

AMPLITUDE

PULSE WIDTH & DUTY RATIO

50 Hz to 10 kHz 1 to 3V p-p –

10 Hz to 10 kHz Min. 3V p-p –

4) Output: Check that the output voltage is 0 V at ON, 30 V

DC or less at OFF.

Check also that the output current is 100 mA or less at

ON, 0 mA at OFF.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

18PP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1861 Rev.6 P. 3 / 3

Andere M-system Controller Handbücher

M-system

M-system MSP4 Bedienungsanleitung

M-system

M-system M8BS2-081 Bedienungsanleitung

M-system

M-system M8PP Bedienungsanleitung

M-system

M-system PSN1 Bedienungsanleitung

M-system

M-system MSP40 Bedienungsanleitung

M-system

M-system MRP10 Bedienungsanleitung

M-system

M-system EAR70 Bedienungsanleitung

M-system

M-system MRP4 Bedienungsanleitung

M-system

M-system MSP5 Bedienungsanleitung

M-system

M-system SC200 Series Bedienungsanleitung

M-system

M-system M8BS2-081 Bedienungsanleitung

M-system

M-system MSP4C Bedienungsanleitung

M-system

M-system SC200W Bedienungsanleitung

M-system

M-system SC100 Series Gebrauchsanweisung

M-system

M-system SC100 Series Bedienungsanleitung

M-system

M-system PSP10 Bedienungsanleitung

M-system

M-system MSP10 Bedienungsanleitung

M-system

M-system SC100 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch