M-system M8SED Bedienungsanleitung

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 60mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within 0 to 55°C (32

to 131°F) with relative humidity within 30 to 95% RH in

order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with ca-

bles, etc.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Output 1 Monitor LED

Output 1

Setpoint Adj.

Output 2

Setpoint Adj.

Output 2 Monitor LED

Mounting Screw

Body

Specifications

INSTALLATION

Use Installation Base (model: M8BSx).

DC ALARM

(thumbwheel switch adjustment) MODEL M8SED

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5488 Rev.2 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

I/O PINS

17.5 (.69)

48 (1.89)

75 (2.95)

83 (3.27)

■CONNECTION DIAGRAM

Installation Base

OUTPUT 1

–

OUTPUT 2

POWER

–

INPUT

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input: Check the power input voltage.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Check that the output load is 125V AC/25VA or 60V

DC/15W at the maximum. For maximum relay life with

inductive loads, external protection is recommended.

When used with a multi-channel installation base (e.g.

M8BS-16), the ratings derated as following.

Terminal block type: 125V AC @ 0.2A, 30V DC @ 0.25A

Cable connector type: 24V AC @ 50mA, 24V DC @ 50mA

ALARM TRIP OPERATION

TRIP

ACTION

OUT

CODE

POWERED UNPOWERED

INP < SET INP > SET

OUT

Hi 1 OFF ON OFF

Hi 2 ON OFF ON

OUT

Lo 1 ON OFF OFF

Lo 2 OFF ON ON

ADJUSTMENT PROCEDURE

Turn the front thumbwheel SW to indicate desired set-

points in %.

Output 1 is for high trip, while Output 2 is for low.

Monitor LED turn ON when the coil is energized; Output 1

coil is energized when the input is above the setpoint, while

Output 2 coil is when the input is below the setpoint.

Relay contact turns ON when the coil is energized with Out-

put Code 1, de-energized with Output Code 2.

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes.

• Hi Setpoint

Increase the input signal from a value lower than the set-

point and check that the relay trips at the setpoint.

• Lo Setpoint

Decrease the input signal from a value higher than the

setpoint and check that the relay trips at the setpoint.

When the trip points are shifted, please contact M-System’s

Sales Ofﬁce or representatives.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

M8SED

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5488 Rev.2 P. 2 / 2

Andere M-system Sicherheitssystem Handbücher

M-system

M-system AYDV Bedienungsanleitung

M-system

M-system AYDV Bedienungsanleitung

M-system

M-system AS4V Bedienungsanleitung

M-system

M-system 10AS Bedienungsanleitung

M-system

M-system 48NDV Bedienungsanleitung

M-system

M-system M6DXAR Bedienungsanleitung

M-system

M-system 48DV Bedienungsanleitung

M-system

M-system 48NDM Bedienungsanleitung

M-system

M-system AS4CT Bedienungsanleitung

M-system

M-system KSE-x2 Bedienungsanleitung

M-system

M-system AS4CT Bedienungsanleitung

M-system

M-system ASD1 Bedienungsanleitung

M-system

M-system R3-AV8 Bedienungsanleitung

M-system

M-system 48NAT Bedienungsanleitung

M-system

M-system 48NDT Bedienungsanleitung

M-system

M-system KSL2 Bedienungsanleitung

M-system

M-system AS4T Bedienungsanleitung

M-system

M-system ASWL2 Bedienungsanleitung

M-system

M-system KS2TR2 Bedienungsanleitung

M-system

M-system M8SED1 Bedienungsanleitung

M-system

M-system AS4R Bedienungsanleitung

M-system

M-system KSL-x5 Bedienungsanleitung

M-system

M-system KS2V3 Bedienungsanleitung

M-system

M-system M2AS Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung