M-system MD7G Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8065 Rev.2 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL BLOCK FOR GROUNDING

(ultra-slim) MODEL MD7G

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Terminal block.....................................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation and connection.

POINTS OF CAUTION

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -25 to +85°C

(-13 to +185°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

•This unit needs a DIN rail as earth grounding bar. Ox-

ide coating of an aluminium rail may lower the electric

conductivity between this module and the ground. Use a

steel or copper rail.

COMPONENT IDENTIFICATION

Body

Spring Loader

DIN Rail Mounting

Adaptor (for grounding)

Connection

Diagram

(left side)

Model No.

Indication

INSTALLATION

Mount the unit on a DIN rail. Once installed, do not move

it to another DIN rail.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook of the DIN rail mounting adaptor at

the rear side of unit, on the DIN rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

C)DIN rails generally have slight individual variability in

size. If you ﬁnd it difﬁcult to push in the lower part, go

back to (A) and hang the upper part more deeply onto the

rail and try (B) again.

DIN Rail

■REMOVING THE UNIT

A)Push down the spring loader utilizing a minus screwdriv-

er.

B)Conﬁrm that it is pulled enough down and pull out the

lower part of the unit.

C)Detach the upper part from the DIN rail.

Spring Loader

MD7G

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8065 Rev.2 P. 2 / 2

TERMINAL CONNECTION

Connect the unit as in the diagram below.

Be sure to ground the DIN rail on which the unit is mounted.

This unit, designed to connect shield wires and cross wires of the protected devices to a DIN rail, is NOT used to ground the

DIN rail.

■EXTERNAL DIMENSIONS unit: mm (inch)

95 (3.74)

(.28)

98 (3.86) [1.5 (.06)]

8–M3 EURO

TERMINAL

DIN RAIL

(35 mm wide)

DIN RAIL

ADAPTOR

WIRE INSERTION ANGLE: approx. 20°

57 (2.24)

1.9 (.07)

■CONNECTION DIAGRAM

2 5

3 6

1 4

DIN RAIL ADAPTOR

(for grounding)

DIN RAIL

Grounding

DO NOT connect to unused terminals.

*1. Oxide coating of an aluminium rail may lower the electric conductivity

between this module and the ground. Use a steel or copper rail.

*2. Be sure to ground the DIN rail.

Recommended grounding resistance ≤100Ω

WIRING INSTRUCTIONS

■EURO TERMINAL

Torque: 0.3 N·m

Applicable wire size: 0.2 – 2.5 mm2

Stripped length: 8 mm

■CAUTION WHEN WIRING

Hold the module steady at the front when you

tighten/loosen screw terminals.

Andere M-system Überspannungsschutz Handbücher

M-system

M-system MMAH Series Bedienungsanleitung

M-system

M-system MDP-JS Bedienungsanleitung

M-system

M-system 6SN Bedienungsanleitung

M-system

M-system MAL-230x Bedienungsanleitung

M-system

M-system MD7TC Bedienungsanleitung

M-system

M-system MDP-4R Bedienungsanleitung

M-system

M-system MD6 24 Series Bedienungsanleitung

M-system

M-system MA-100 Bedienungsanleitung

M-system

M-system MD7PL Bedienungsanleitung

M-system

M-system MD73W Bedienungsanleitung

M-system

M-system MAKN Bedienungsanleitung

M-system

M-system MD7JS Bedienungsanleitung

M-system

M-system MDR2 Bedienungsanleitung

M-system

M-system MDP-LWA Bedienungsanleitung

M-system

M-system MDP-SP Bedienungsanleitung

M-system

M-system MDCAT-SPE-A Bedienungsanleitung

M-system

M-system MDPA-24 Bedienungsanleitung

M-system

M-system MDP-24T Bedienungsanleitung

M-system

M-system MDK-LC Bedienungsanleitung

M-system

M-system MDP-TL Bedienungsanleitung

M-system

M-system MD7RB-FF Bedienungsanleitung

M-system

M-system MDP-LWA Bedienungsanleitung

M-system

M-system MD7FB Bedienungsanleitung

M-system

M-system MDH Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung

Intermatic

Intermatic PS3000 Bedienungsanleitung

ASCO POWER TECHNOLOGIES

ASCO POWER TECHNOLOGIES 360 Bedienungsanleitung