M-system FDU Bedienungsanleitung

FDU

P. 1 / 2 EM-1428 Rev.5

INSTRUCTION MANUAL

MODEL FDU

CURRENT LOOP SUPPLY

(10 – 50mA loop)

INSTALLATION

Pulloutthebodyinpressingtheclampslocatedatthetopand

bottom of the unit for separating it from the base socket.

■ DIN RAIL MOUNTING

Set the base socket so that its

DIN rail adapter is at the bot-

tom. Hung the upper hook at

the rear side of base socket on

the DIN rail and push in the

lower. When removing the

socket, push down the DIN

rail adapter utilizing screw-

driver (–) and pull.

■ WALL MOUNTING

Refer to the drawings in the following page.

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the

connection diagram label on the unit side.

CHECKING

1) Terminal wiring: Check that all cables are correctly

connected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal 7

–␣ 8 with a multimeter.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Output: Check that the load resistance meets the de-

scribed specifications.

DIN Rail

35mm wide

Spring Loaded

DIN Rail Adaptor

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

package you received as below.

If you have any problems or questions with the product,

please contact M-System's Sales Office or representatives.

■ PACKAGE INCLUDES:

Signal conditioner (body + base socket) ................. (1)

■ MODEL NO.

Check that model No. described on specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, installation, connection and basic mainte-

nance procedures.

COMPONENT IDENTIFICATION

■FRONT PANEL CONFIGURATIONS

Body Base Socket

Specification Label

Connection

Diagram Label

(side)

Span Adj.

Zero Adj.

–

OUTPUT

U(+)

V(–) POWER

–

2-WIRE

TRANSMITTER

–

MONITOR

(10 – 50mA DC)

FDU

P. 2 / 2 EM-1428 Rev.5

EXTERNAL DIMENSIONS mm (inch)

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

specifications, therefore you usually do not need any calibra-

tion.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■ HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufficient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above procedure

1) – 3).

POINTS OF CAUTION

■ GENERAL

• Before you remove the unit from its base socket or mount it,

turn off the power supply and input signal for safety.

■ ENVIRONMENT

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing and ventilate it.

• Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within -5 to +55°C (23

to131°F)withrelativehumiditywithin30to90%RHin order

to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the "ADJUST-

MENT PROCEDURE" explained earlier.

26 (1.02)

93 (3.66)

(.59)

2–4.5 (.18)

HOLE

15 (.59) deep

8–M3.5

SCREW

7.8 (.31)

107 (4.21)

35.4 (1.39)

DIN RAIL

35mm wide

[3.3 (.13)]

CLAMP

(top & bottom)

137 (5.39)

•When mounting, no extra space is needed between units.

26 (1.02)

100 (3.94)

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

Andere M-system Prüfgeräte Handbücher

M-system

M-system FDY2 Bedienungsanleitung

M-system

M-system M6NPP Bedienungsanleitung

M-system

M-system W2PP Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2XPA3 Series Bedienungsanleitung

M-system

M-system Mini-M M2CRS Bedienungsanleitung

M-system

M-system Mini-M Series Bedienungsanleitung

M-system

M-system AD2LC Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2MS Series Bedienungsanleitung

M-system

M-system Mini-M M2VV Bedienungsanleitung

M-system

M-system M6DPP Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system Mini-M M2PHS Bedienungsanleitung

M-system

M-system M2PA Series Bedienungsanleitung

M-system

M-system Mini-M Series Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2RS Series Bedienungsanleitung

M-system

M-system M2PRU Bedienungsanleitung

M-system

M-system Mini-M M2LMS Bedienungsanleitung

M-system

M-system Mini-M Series Bedienungsanleitung

M-system

M-system Mini-M M2PP Bedienungsanleitung

M-system

M-system Mini-M M2CDS Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2VF2 Series Bedienungsanleitung

M-system

M-system Mini-M M2MST Bedienungsanleitung

M-system

M-system Mini-M M2AMS2 Bedienungsanleitung

M-system

M-system Mini-M M2XF2 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung