MachPower WL-AC5250-047 Bedienungsanleitung
NETWORK CONTROLLER PER WIRELESS AP
WL-AC5250-047
2
3
Thanks
for choosed our product
___________________________________________________________________
INDEX
Chapter 1 Manual Introduction
Chapter 2 Products Introduction
2.1 Products description
2.2 Products properties
2.2.1 Hardware property
2.2.2 Software property
2.3 Product layout
2.3.1 Front Panel
2.3.2 Rear Panel
2.3.3 Connection
Chapter 3 Configuration Guide
3.1 Login Web Interface
Chapter 4 Function Setting
4.1 Device List
4.2 Device Group
4.3 Device Log
4.4 Address Server
4.5 Gateway
4.5.1 LAN Setting
4.5.2 WAN Setting
4.5.3 Cloud Setting
4.5.4 Authentication
4.6 Gateway
4.6.1 IP/Port Filtering
4.6.2 MAC Filtering
4.6.3 URL Filtering
4.6.4 Port Forwarding
4.6.5 DMZ Settings
4.7 Storage/Server
4.8 Management
4.8.1 System management
4.8.2 QoS
4.8.3 User management
4.8.4 Device Log
4.8.5 Upgrade Firmware
4.8.6 System Time
4.9 Device Status
4.9.1 Basic Status
4.9.2 LAN Status
4.9.3 WAN Status
4.10 WAN Status
Chapter 5 Appendix A Product SPEC
4
CHAPTER1
MANUAL INTRODUCTION
This manual is subject to tell users how to use this WLAN management platform properly, suit for those familiar with basic networking
knowledege and terminology. Then this user manual including the connection of AC controller, description of this platform’s properties,
and how to configure this platform; Pre-reading this manual before operation is highly recommended.
CHAPTER2
PRODUCTS INTRODUCTION
2.1 Products description
WL-AC5250-047 is a highly performance WLAN controller, specially for Indoor and outdoor wireless access points which set up in hotel or
small-medium sized enterprise; It’s capable for managing all Access point, support AP auto-detection, AP status preview, AP configura-
tion,MAC filtering, AP software upgrade simultaneously to provide high quality&performance& reliability,easy installation&maintenance
WIFI service to different clients;
2.2 Products properties
2.2.1 Hardware property
• Deploy dual core CPU, 880Mhz frequency
• Deploy high capacity&speed memory, up to 516M DDR3 SDRAM;
• 5 x 10/100/1000Mbps Gigabit Ethernet port
• 1 x TF Card Slot
2.2.2 Software property
• WL-AC5250-047 detect and connect to wireless access point automatically, no need to configure any AP, realize true centralized AP
management function
• Monitor AP status in real-time,auto-inspection AP’s working status(up or down), show each ap status under interface page;
• Configure related properties to each AP simultaneously, like setting SSID,connection type, Security type,etc;
• Adjust WIFI RF output manually, to fit for different networking environment, to maximum WIFI coverage;
• AP address server function can allocate IP address for different AP working in the same segment, no need to set up AP’s IP address
manually;
• Support smart gateway mode, working as a Gigabit router, to realize router, AC, AP address server function in the same unit;
• Adjust each AP’s WIFI settings like Channels or location remark, providing auto-restarting functions on AP;
• Support WIFI MAC filtering, only allow the device, whose MAC address is in the rule list, to have WIFI access, make sure a securer network
allowed;
• Full WEB management, clear and concise ,make AP management easier and much convenient;
2.3 Product layout
2.3.1 Front Panel
• WL-AC5250-047 front panel is like following:
Led indicator
LED light Name Indication
Power Power Light
Power is on, means status is up;
Power is off, mean status is down;
Run System Light
Flashing,means system status is normal
OFF or stable steady, means status is abnormal
TF TF Light
Light is ok, means TF card loaded successfully
Light is off, means TF card is not loaded
5
Reset button
If need to restore the WL-AC5250-047 into factory default, please do following procedure: Power on WL-AC5250-047, use a pin to press
and hold the reset button until all LED becomes quick-flash from slow-flash.
Then release the button and wait WL-AC5250-047 to reboot to its factory default settings. After that, the default IP address of WL-
AC5250-047 is still 192.168.10.1,default user name and password are both admin RJ45 Ports: 5x10/100M/1000Mbps auto-negotiation
RJ45 Ethernet Port; Support any connection devices in 10/100M/1000Mbps bandwidth;
Notice
LAN/WAN port is LAN port only on the default mode, only when WAN setting is enabled then LAN/WAN port will change to WAN port;
2.3.2 Real Panel
DC Jacket
DC Jacket located on the right side of WL-AC5250-047’s real panel, input power should be ac power 100-240V~ 50/60Hz 0.3A
Anti-thunder ground connection:
Please deploy ground connection to avoid lightening stroke, by copper core cable in yellow and green jacket;
For detailed installations please refer to related manuals, like “Anti-thunder installation guide in devices”
Attention:
Please use original power cord for installation; Set locate power outlet near the devices, to make safer and easier installation and
operation
2.3.3 Connection
Please power the AC controller, and connect the AP in following working diagram:
DSL WL-AC5250-047 SWITCH
AP
AP
AP
Please note, in above picture, can make Wireless AP connect with PoE switch, PoE switch’s uplink port connect with AC controller’s
WAN port, total connection will be based on the application environment.
CHAPTER3
CONFIGURATION GUIDE
3.1 Login Web Interface
Please confirm the following points before login WL-AC5250-047:
1. Connect the managment host (PC) to LAN port of AC controller or UP-link port of switch in the whole networking.
2. The management host(PC) has been properly installed IE 7.0 or higher browser version
3. The management host’s IP address has been set the same network segment with WL-AC5250-047, namely 192.168.10.X (X is betwe-
en 2-254 arbitrary integer Number), a subnet mask of 255.255.255.0.
4. In order to ensure a better effect of Web interface displays, it is recommended to adjust the display resolution to 1024 × 768 or
more pixels.
Operation Steps:
A. Open IE browser, Input http://192.168.10.1 in the address bar to login WL-AC5250-047 Web management interface.
B. Now you must enter username and password, the factory default is:
Username: admin
Password: admin
click “OK”
6
C. After a successful login, then see WL-AC5250-047 Web interface page.
In the above Web Interface Page, there are three part.
It is the main menu area on the left, to show this WLAN controller’s main function.
It is the AP List on the middle part, to show the Wireless AP info which access into this WLAN controller.
It is the function on the right part. For example, click Device List, will show the function of Device List.
CHAPTER4
FUNCTION SETTING
4.1 Device List
Device list show the current wireless AP access into WL-AC5250-047, display the total quantity/Online/Offline Wireless AP connected
to WL-AC5250-047, Then Wireless AP’s name, IP address, MAC address, QTY of end users, Firmware version, Channel as showed in
following picture:
Let’s introduce following button one by one:
Select: click the white box to make hook, mean select this AP
Blue balloon: Click it to set the AP’s Location and Device name, fill in the right info if needed, will be showed in Device list when Apply.
Picture showed as follow:
7
SN: Show how many AP access into this AC controller
Location: show where the AP setup
Name: what’s the name of this AP.
Device IP: AP’s IP address, click this IP address, can access into AP’s GUI when you set an static IP address for your PC in same IP
segament. If many AP in the device list and you want to find out one AP, you can input this AP’s IP address for quickly search.
Device MAC: AP’s MAC address, if you want to find out one AP quickly by MAC address, just input the MAC address in top of this GUI,
then search.
Users: How many end users access into this AP
Version: The firmware version of this AP
Channel: the channel of this wireless AP
Online Time: How long this wireless AP online and access into this AC controller.
Group: you can set some AP in one group, then this part will show group name mainly.
Config: click icon under config will show following picture: From this picture, will show each AP’s status, Basic info,and advanced
setting. If any data you want to make, then Apply to finish.
Device Status: show AP’s Model number, online time, MAC address, IP address, firmware info, channel, RF Power showed in above
picture.
Device Network: Show the Wireless AP’s WAN network info and IP address
8
Wireless Basic: Mainly to setup the AP’s SSID, VLAN, Security.
For the VLAN, the top networking should be with VLAN switch, and input the switch’s VLAN ID in the blank part. The VLAN ID range
is 0~4094.v
Wireless Advanced: user can configure the AP’s mode, channel, Fregament Threshold, coverage threshold, Max Station.
Remark: For Fragment Threshold, RTS Threshold, Beacon Interval, Aggregation, ShortGI, Rev Option, we recommand to keed in
default.
Max Station, mean QTY of end users. 0 mean no limited.
Coverage Threshold: Applicated in Roaming mainly, the working status showed as follow:
Connected AP: Show how many pieces AP connected into this AC controller, and how many AP can access into this AC controller.
Online AP: QTY of AP which online in this AC controller
Offline AP: QTY of AP which offline in this AC controller
Users: Mean how many end users access into this AC controller.
9
ALL AP: Mean now show all the online AP, offline AP. Can select online AP or offline AP.
Refresh Interval: mean how long this AC controller will refresh the AP QTY.
Search by IP: mean search the wireless AP by IP address, make hook in the white box, input IP address, then search.
Search by MAC: mean search the wireless AP by MAC address, make hook in the white box, input MAC address, then search
Batch Set: mean can configure the wireless AP’s data in batch.
Refresh: Scan the AP list again.
Delete: Select some AP, then delete from this AC controller.
Reboot: Select some AP, then restart this AP
Reset: Select some AP, revert to factory default.
Upgrade: can upgrade firmware for wireless AP.
4.2 Device Group
Click Device Group at first, then will show New/Delete, Click New, then configure the data in Wireless Basic and Wireless Advanced
part; Please note, this data will be applicated for all the AP in this group. After finish all, set an group name, then Apply to finish.
For detail procedure, please refer to following picture:
Add /Remove AP into group:
Please following the step showed in following picture:
10
4.3 Device Log
Device Log show AP’s record, such as on line recording, offline recording, device configuration recording.
4.4 Address Server
Through Address Server, to set server IP address, subnet mask; Server address Pool, main to assign IP address to the connected
wireless AP, no need to specify the IP address for wireless AP manually when operation.
Server IP Address: modify the default AP address server’s IP address; (default is 192.168.188.1)
Server Subnet: Modify AC controller’s subnet; 255.255.255.0 in default
Server Address Pool: When wireless AP connected with this address server, then address server will assign IP address for wireless
AP. (The default IP address pool is 192.168.188.2-192.168.188.254)
4.5 Gateway
4.5.1 LAN Setting
LAN IP Setting: Set IP address for LAN
Subnet mask: Set Subnet mask for LAN
DHCP Server: Enable mean it will assign IP address for users.
DHCP IP Count: DHCP Client IP mean the IP address range assigned by DHCP Server.
DHCP Lease Time: The networking device get IP lease time from DHCP server.
Static Bind IP-MAC List: Can delete it the IP/MAC address from this list if no need to bind.
Local IP-MAC List: Can add/refresh the IP/MAC list connected into this AC controller.
Inhaltsverzeichnis
