Macrom KIT7WBR Bedienungsanleitung

USER MANUAL

KIT7WBR

7-inch monitor kit + magnetic wireless rear view camera with built-in battery

KITKIT

WIRELESSWIRELESS

- 2 -

• Before completing the installation, temporarily connect the wiring and make sure it works

properly.

• Use only the parts included with the unit to ensure proper installation.

Using parts not included in the package may cause malfunctions.

• This product must be installed by an authorized reseller to qualify for warranty.

• Install the unit in a location that will not harm the driver or passenger to avoid collision in the

event of a sudden stop such as an emergency stop.

• Avoid installing the unit in places subject to high temperatures, such as direct sunlight, hot air,

or where it would be subject to dust dirt or excessive vibration.

• Be sure to remove the front protective film after installing the unit.

Installation

Monitor setup

Choose the position of the monitor in the vehicle so that it does not block your view and complies

with local laws for safe driving.

1. Dashboard

2. Support 1

Magnetic camera installation

Choose the position of the camera on the vehicle and make sure that the surface on which it will be

placed is metal.

To ensure proper adhesion, do not place the camera on uneven or rough surfaces.

However, it is good practice to clean the surface before applying the magnetic camera.

Note:

Before drilling the holes in the dashboard necessary for fixing the U-shaped support, make sure

there are no obstacles such as ventilation pipes underneath or electrical wiring.

- 3 -

Connections

Wifi Antennas

1. Connect the Wifi antennas paying attention to the operating frequency indicated on the antenna

( A ), 2.4 Ghz, ( B ), 433 Mhz,

BAB

Power Supply

1. Connect the monitor harness to your vehicle’s cigarette lighter.

2. Press the (Power) button on the top of the cigarette lighter to turn the monitor on or off.

3. As an alternative to the cigarette lighter wiring, a direct connection can be made to the car’s

ignition switch. Make sure there is a 10 Ampere protection fuse.

4. To charge the battery of the camera it is necessary to connect the USB type C to a charger with

an output voltage of DC 5V and a current of 2A.

NOTE: Before using the camera, make sure it is fully charged.

Charging time may vary depending on the actual charge of the product.

Maximum recharge time about 9 hours.

The battery charger is not supplied.

Power button and charging indicators

2. On the side of the camcorder you will find the Power button and

battery charge indicators

3. Power button (On/Off)

4. Battery charge indicators 25%-50%-75%-100% 2

Power connection via

cigarette lighter wiring

Connections Power via ACC

USB charging cable

- 4 -

Front panel

1. Power Key (On/Off)

2. Key Previous / Decrease brightness

3. Key Next / Increase brightness

4. Rear view camera channel selection key

5. Menu key

6. SEL / Record & Stop key

7. Wi-Fi antennas

Product overview

Warning:

The images in this manual are indicative only and may differ from the actual product. Please refer to the actual device unit.

12 3 4 5 6

Remote control

1. Start button for Recording / Stop (Note: SD card is required to be inserted)

2. Power key

3. Guidelines shortcut key

4. - Decrease brightness

- Key Previous

5. Menu access key

6 - Increase brightness

- Key Next

7. - Change channel

- CH1---CH2---CH3---CH4 (Screen split)

8. Displays the CH1 channel screen

9. Displays the CH3 channel screen

10. Displays the CH2 channel screen

11. Displays the CH4 channel screen

- 5 -

Important

Before proceeding with the use of the monitor it is necessary to pair a rear view camera using the

pairing function.

Note

Before using and pairing the camera make sure it is fully charged.

Charging time may vary depending on the actual charge of the product.

Maximum recharge time about 9 hours

Rear view camera pairing

1. Using the key (CH) select the channel to which you want

to connect the camera.

2. Enter the menu and select PAIRING to pair.

Press the SEL key to confirm the procedure.

3. The monitor shows the pairing procedure via “countdown”

on the screen

4. At the end, the image of the previously paired camera will

be displayed.

NOTE:

If you need to pair more cameras, please repeat the above procedure again selecting the

corresponding channel.

- 6 -

Video Recording / Playback

Recording mode

Before proceeding with the recording it is necessary to format

the new SD card.

Select the Recording mode using the cursor < / > and

confirm the "Format" selection by pressing the SEL key.

Confirm again to format the SD cards.

To make a recording, press the SEL key, a flashing red dot

appears on the screen

To end the recording, press SEL again.

Insert an SD card

Using a Phillips screwdriver, open the SD card door on the back

of the monitor and insert the SD card.

It is recommended to use a class 10 high-speed TF card (minimum)

or higher. Maximum allowed capacity of 128Gb.

Note:

The recording of the video signal relates only to the image of the camera/s displayed on the screen. If you

want to make multiple recordings, you need to display multiple cameras on the screen at the same time

so that the monitor can simultaneously record multiple channels.

Circular Registration

If you want to overwrite the entries, you must activate the

"Circular logging" function.

Select the Recording mode using the cursor < / > and confirm

the selection "Circular recording" by pressing the SEL key and

confirm again to activate the function.

Note:

When the function is active, the symbol appears on the

screen to confirm that overwriting has been activated.

Note:

When the SD is inserted, the symbol appears on the screen which

confirms the presence of the SD card. If the symbol turns out to be red, the

class of the SD does not comply with the specific requests of the product.

Video playback

If you want to view the recordings you need to access the Play

function. The video list will be shown in sequence of date and

time of recording.

Note:

Each recording segment has a maximum duration

of 60 seconds.

Each file is approximately 4 megabits in size.

- 7 -

System settings

Image settings

Access the menu and select image using the cursor < / > and

confirm the selection using the SEL key.

Select the Brightness / Contrast / Color functions using the

cursor < / > and confirm your selection by pressing the SEL

key.

Modify the desired value of the selected function and press

menu to exit the configuration.

Image rotation

Enter the menu and select Mirrors using the cursor < / > and

confirm the selection using the SEL key.

Select the rotation of the desired image using the cursor < / >

and confirm the selection by pressing the SEL key. Press menu

to exit setup.

Split mode setting

Enter the menu and select Mode using the cursor

< / >

and

confirm the selection using the SEL key.

Select the viewing mode of the screen with the images you wish

to view using the cursor

< / >

and confirm your selection by

pressing the SEL key.

Press menu to exit setup.

Impostazione della fotocamera

Enter the menu and select Mode using the cursor < / > and

confirm the selection using the SEL key.

Select the viewing mode of the screen with the images you

wish to view using the cursor < / > and confirm your selection

by pressing the SEL key.

Press menu to exit setup.

Note: it is possible to set the automatic rotation cycle of the

display (1-2-3-4) and the desired time.

System setup

Access the system settings and select image using the

cursor < / > and confirm the selection using the SEL key.

Select the functions: Date-Time / Language / Trigger

/ Guidelines / System Reset using the cursor < / > and confirm

your selection by pressing the SEL key.

Modify the desired value of the function select and press menu

to exit the configuration.

Note it is possible to set the automatic rotation cycle of the

display (1-2-3-4) and the desired time.

- 8 -

Specifications

Monitor

Screen .............................................................................................................................. 7’’ AHD IPS

Resolution ................................................................................................................ 1024xRGB*600P

Contrast ..................................................................................................................................... 600:1

Power Supply .................................................................................................................... DC12V-36V

Maximum current level ................................................................................................................ 10A

System....................................................................................................................PAL/NTSC (AUTO)

Connection ...................................................................................................................................WiFi

Registration

Mode.......................................................................................................QUAD-Vision 4 retrocamera

Video..............................................................................................................................................Mp4

Images........................................................................................................................................... JPG

Support

Typology ...................................................................................................................... Full SD HC/XC

Maximum capacity.................................................................................................................... 128Gb

Speed ................................................................................................................ Class 10 (minimum)

Bus SD....................................................................................................................................... UHS-I

Category ................................................................................................................... High Endurance

Note:

The Endurance category guarantees a greater amount of overwriting than traditional SD.

WiFi

Integrated Wi-Fi.............................................................................................................2.4G wireless

Network range............................................................................................................ 2403-2480MHz

Distance ............................................................................................................ ≤200m in open field

Camera

Sensor ................................................................................................................................. 1/3’’ AHD

Risolution ........................................................................................................................... 1280*720P

Viewing angle............................................................................................................. 110°[H] 140°[D]

Waterproof ................................................................................................................................... IP68

Night lighting ...................................................................................................................IR (infrared)

Night vision distance ............................................................................................................5 meters

Battery

Battery capacity ...................................................................................................................6700mAH

Charging time ............................................................................................................................. 9 ore

Operating time .......................................................................................................................... 16 ore

Charging power supply....................................................................................................USB Type-C

Type of battery charger ..................................................................................................... DC 5V - 2A

Battery charge indicators ................................................................................25%-50%-75%-100%

Installation .............................................................................By magnet wrapped with rubber case

www.macrom.it

Inhaltsverzeichnis

Andere Macrom Monitor Handbücher

Macrom

Macrom M-AN700DAB Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung