MadStad Engineering MadStad Bedienungsanleitung

Please read this entire manual before proceeding with installation.

What is in the box:

(1) Set of preassembled MadStad adjustable windshield brackets

(2) Pre-assembled fork-mount brackets

(2) M8 x 50mm bolts

(2) M8 aluminum spacers

(2) M10 x 50mm bolts

(2) M10 aluminum spacers

(4) M5 Philips screws

(4) M5 plastic washers

(4) soft rubber washers

The MadStad quick-release windshield (and optional fly screen) clip onto compact

brackets that stay attached to the forks. Pages 2 and 3 show how to attach these brackets.

Windshield Installation

Once bracket installation is complete, the windshield attaches to the brackets with four

Phillips truss screws, plastic flat washers and rubber washers as shown below. You can prep

the shield first by inserting each screw and washers into each windshield hole from the front,

and pushing the rubber washer on from the back to hold the screw in place.

Once all four screws are on the shield, set it against the brackets and run the screws into the

rubber well nuts. The rubber well nuts are flexible and shield holes are oversized so you can

nudge the shield around to align the

screws with the holes properly. Get two

of the screws started on one side of the

bike to keep them from coming out,

then move over to the other two. When

all four are in then tighten them all

snugly but DO NOT OVERTIGHTEN!

Too much torque and you could

damage the well nuts.

Adjustable Windshield System

Triumph Rocket III

MadStad Rocket III Installaon

Fork-Mount Brackets:

Aaching the Windshield or Fly Screen:

1. Position the locking tab away

from the two mounting slots.

2. Set brackets onto aluminum

mounng spools.

3. Fully seat brackets into

the slots on the spools.

4. Pull up on the locking tab

and rotate onto the spools.

5. Make sure the locking tab is fully

pushed down over the two spools.

Remove the factory bolt on the

top fork clamp. Install bracket

as shown then fully ghten both

top and boom.

Remove the factory top bolt on

the boom fork clamp. Install

bracket as shown below but do

not fully ghten.

We recommend that you snap

the windshield brackets onto

the bike BEFORE aaching the

windshield. Once the shield

brackets are locked in place,

then screw the shield to the

brackets. Aer that you can

remove and install them as a

unit.

Install these rst. Everything

else aaches to these brackets.

Aaching the Lower Deectors:

Set brackets onto aluminum

mounng spools. Rotate

locking tab up as shown.

Fully seat brackets into the

slots on the spools.

Pull up on the locking tab and

rotate between the spools. You

may need to push on the spring

from the inside.

Make sure the locking tab is fully

pushed down between the two spools.

Adjusting the Brackets

The knob screws release the brackets allowing the windshield to slide and tilt. These knob

screws must always be tightened securely before riding. DO NOT attempt to adjust the

brackets while riding! You must come to a complete stop before making adjustments. Also

make sure that you do not set the windshield in such a way that causes your handlebars or

hand guards (if installed) to hit the windshield when turning, or before reaching full lock.

To make height adjustments, loosen the knobs 1 turn and pull up or push down on the

shield so the top edge is at about your chin level as you look straight ahead. Loosen the

knobs 2-3 turns to set the angle at about the middle of the bracket range, tighten the knobs

and go for a ride to test. Do this on a calm day if at all possible; windy days make it hard to

judge the airflow.

Disclaimer

Neither MadStad Engineering nor its owners shall be liable for any damages, consequential or

inconsequential, resulting from the use of our products. Installation of any of our products

constitutes acceptance of these terms.

It is the responsibility of the user to make sure all fasteners are tightened securely, the

windshield is mounted properly and the adjustment knobs are tightened snugly before putting

the motorcycle in motion. MadStad systems ARE NOT intended to be adjusted while the

vehicle is in motion; you must pull over out of the way of traffic and come to a complete stop

before making any changes. The user must never place the windshield in such a position as to

interfere with the safe and complete movement of the handlebars and controls.

Returns and Warranty

If you are not satisfied with your new windshield system you have 30 days to return it. Full

details are available on our web site at www.madstad.com. If purchased from a dealer then

please contact the dealer for their return policy.

MadStad adjustable brackets carry a lifetime warranty against manufacturing defects. This

does not include cosmetic issues nor any parts that inherently wear out or degrade over time

such as rubber and plastic parts. Windshields, deflectors and other similar plastic parts are

warrantied for 1 year against manufacturing defects, not against cosmetic issues or issues

related to normal wear and tear.

MadStad Engineering, Inc.

1451 E. Jefferson St., Brooksville, FL 34601 USA

Phone: 352-848-3646

Email: suppor[email protected]

Thank you for your support, and ride safely!

Andere Handbücher für MadStad

Andere MadStad Engineering Motorradzubehör Handbücher