Maestro MR 850 Bedienungsanleitung

Model/Модель: MR 850

091

Сerticated in Ukraine

Виріб сертифіковано в Україні

Owners manual. Electric Meat Grinder

Bedienungsanleitung. Elektrischer Fleischwolf

Instrukcji obsługi. Elektryczny maszynki do mielenia mięsa

Manualul proprietarului. Masina de tocat carne electrica

Руководство по эксплуатации. Электрическая мясорубка

Керівництво з експлуатації. Електрична м’ясорубка

Pictures/ Paveikslai/ Rysunki/ Figuri/ Рисунки/ Малюнки

Description of the appliance..............................................................4

Gerät......................................................................................................12

Konstrukcja urządzenia........................................................................21

Structura produsului..............................................................................30

Устройство прибора..............................................................................38

Складприладу......................................................................................46

12 10 9 8

11 13

Dear customer, we thank you for purchase of goods!

Functionality, design and conformity to the quality standards guarantee to you reliability

and convenience in use of this device.

Please read and comply with these original instructions prior to the initial operation of your

appliance and store them for later use of subsequent owners.

The Meat Grinder is intended only for the preparation of beverages in living (home) conditions.

Under condition of observance of user regulations and a specialpurpose designation,

a parts of appliance do not contain unhealthy substances.

TECHNICAL SPECIFICATIONS

Model: MR-850

Electrical supply:

Alternating current- AC;

Rated voltage 220-240V;

Max locked power: 220-240V, ~50 Hz, 1500W;

Rated power : 220-240V, ~50 Hz, 500W;

Protective class II

Protection class IPX0

This appliance is equipped with a thermostat system.This system will automatically cut o the

power supply to the appliance in case of overheating

Description of the appliance

Picture1| page 2

1. ON/OFF switch

2. Body

3. Fasten button

4.Tube inlet

5. Food pusher

6. Hopper plate

7. HeadTube

8. Snake

Safety instructions

When using your appliance, basic safety precautions should always be followed,

including the following:

- DO NOT leave the appliance unnecessarily plugged in. Disconnect the plug from the mains when the

appliance is not being used.

- Always turn o the switch (time controller) and take electrical connector out of socket before cleaning

and storage.

- DO NOT use the power cord or the appliance in order to pull the plug out of the socket.

- Only plug the appliance into an outlet with an earthed (ground) contact.

- In the interest of safety, regular periodic close checks should be carried out on the supply cord to ensure

no damage is evident.

Should there be any signs that the cord is damaged in the slightest degree, the entire appliance should be

returned be authorized service engineer.

-If your device was brought from cold to warm room, do not switch it on within 2 hours to prevent

damage due to condensation on internal parts

-This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

- Do not operate the appliance if damaged, after an appliance malfunctions or it has been damaged in any

manner, return to at authorized service engineer for repair.

- DO NOT let children or untrained persons use the appliance without supervision.

- Keep the power cord away from the hot and sharp surfaces.The power cord should not touch the top

9. Cutting blade

10. Cutting plate (ne)

11. Cutting plate (medium)

12. Fixing ring

13. Sausage

14. Kebbe

15. Shredder attachment

part and the back wall of the oven during its operation.

- Do not let the cord hang over the edge of a table or counter or touch hot surfaces.

- Не бросайте прибор.

- DO NOT leave the appliance exposed to the weather (rain, sun, etc.).

Actions in extreme situations:

- If a device tumbled into water, immediately, unplug the device, not touching to the device or water.

- In case of appearance from appliance of smoke, sparkling, strong smell of a burn isolation,

immediately stop use the device, unplug the device, appeal to the nearest service center.

ATTENTION!

- Never use your nger or an objection to push ingredients down the feed tube while the appliance is

running. Only the pusher is to be used for this purpose.

- Do not touch moving parts during the operation

- Always disconnect appliance before cleaning, assembling,

disassembling, loading and unloading products. Perform assembly and disassembly only after full stop

of moving

parts.

Do not use the appliance if the mains cord, the plug or other parts are damaged

In case of failure to observe the rules a danger of serious damages may arise!

Never use any accessories of parts from other manufacture .Your guarantee will become invalid if such

accessories or parts have been used.

-THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY. DO NOT USETHE APPLIANCE FOR ANYTHING OTHER

THAN INTENDED USE.

Do not use it for commercial purpose.

Preparation for work

- Remove all wrap materials and stickers

- Make sure that all the parts of appliance don’t have damages.

-Thoroughly clean the parts that will come into contact with food before you use the appliance for the

rst time.

We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

- Switch the appliance o before detaching and install any accessory.

Wait until moving parts have stopped running before you remove the parts of the appliance.

ASSEMBLING

- Press the fasten button hold the head and insert it into the inlet(when inserting please pay

attention the head must be slanted as per arrow indicated on the top, see g.2.1,then move the head

anticlockwise so that the head being fastened tightly (g.2.2)

g.2.2

- Place the snake into the head, long end rst, and turn to feed the screw slightly until it is set into the

motor housing (g. 2.3)

- Place the cutting blade onto the snake shaft with the blade facing the front as illustrated (g.2.4).

If it is not tted properly, meat will not be grinded.

- Place the desired cutting plate next to the cutting blade, tting protrusions in the slot (g.2.5)

- Support or press the center of the cutting plate with one nger then screw the xing ring tight with

another hand (g.2.6). Do not over tighten.

g.2.3 g.2.4

g.2.5 g.2.6

- Place the hopper plate on the head and x it into position.

- Locate the unit on a rm place.

-The air passage at the bottom and the side of the motor housing should be kept free and not blocked.

Mincers are fed with sinewless, boneless and fatless beef that has been cut into pieces approximately

20 mm x 20 mm x 60 mm. Pushers are pressed with a force of 5N against the meat. Do not use the

appliance for more than 5 minutes consecutively. Leave the appliance to cool for 10 minutes before using

again.

Mincer

- Insert the worm shaft into the cutter housing, the plastic end rst.

- Place the cutter unit onto the worm shaft. (The cutting edges should be at the front)

Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) onto

the worm shaft. (Make sure the notch of the grinding disc t onto the projections of the mincer head.)

Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened.

- Attach the cutter housing to the motor unit.

Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle and sinews as much as

possible. (Never use frozen meat!)

Put the meat in the tray. Use the pusher to gently push the meat into the cutter hosing. (For steak tartare

, mince the meat with the medium grinding disc twice.)

If the appliance is locked, please press Reversal button(REV).The meat locked in cutter housing is

untrodden, so the appliance can renew its usual condition.

Meat left behind in the cutter housing may be removed from the inside of the appliance by passing a

slice of bread through the cutter housing.

Making kebbe

Insert the worm shaft into the cutter housing, the plastic end rst.

Place the cone in the cutter housing.

Place the former on the cutter housing and screw the ring on the cutter housing.

Place the tray on the upright part of the cutter housing.

Now the appliance is ready for making kebbe.

Feed the prepared kebbe mixture through the kebbe maker. Cut the continuous hollow cylinder into the

desired lengths and user as required.

Kebbe is a traditional Middle Eastern dish made primarily of lamp and bulgur wheat which are minced

together to form a paste the mixture is extruded through the kebbe maker and cut into short lengths .

The tubes can then be stued with a minced meat mixture, the ends pinched together and then deep

fried.

Making sausages

- Mince the meat Insert the worm shaft into the cutter housing , the plastic end rst.

- Place the separator in the cutter housing.

- Place the sausage horn on the cutter housing and screw the ring on the cutter housing.

- (Make sure the notches of the separator t onto the projections of the mincer head.)

- Attach the cutter housing to the motor unit.

- Place the tray on the upright part of the cutter housing.

- Now the appliance is ready for making sausages.

- Put the ingredients in the tray. Use the pusher to gently push the meat into the cutter housing.

- Put the sausage skin in lukewarm water for 10 minutes.Then slide the wet skin onto the

sausage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets stuck onto the

sausage horn, wet it with some water. (g.3)

g.3

Shredder

- Press the fasten button, hold the plastic cutter housing and insert it into the tube

inlet (when inserting please pay attention the plastic cutter housing must be slanted as per arrow

indicated), then move the plastic cutter housing anticlockwise until it is fastened tightly, and release the

fasten button.

- Place the shredder drum into the plastic cutter housing, then move the shredder clockwise so

that it being properly fastened.

- Place the pusher on the upright part of the plastic cutter housing, and use the pusher to gently

push the vegetable into the plastic cutter housing.

- Now the appliance is ready for cutting. (g.4)

CLEANING AND MAINTENANCE

ATTENTION!

- Before you clean the appliance, switch the appliance o and remove the plug from the socket

- Never immerse the motor unit in the water or any other liquid, nor rinse it under the tap. Use only a

moist cloth to clean the motor unit.

- Never immerse the appliance or part of it in water.

- Do not use any strong or abrasive solvent, sponge or cream cleaner. Do not put in the dishwasher.

Press the release button and turn the whole cutter housing in the direction of the arrow.Remove the

pusher and the tray.

Unscrew the screw ring and remove all parts of the cutter housing. Do not clean the parts in the

dishwasher!

g.4

Wash all parts that have come into contact with meat in hot soapy water. Clean them immediately

after use. Rinse them with clear hot water and dry them immediately.

We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

Storage

- Switch o the appliance and let it completely cool before storage.

-Wipe and dry the appliance before storage.

- Store the appliance in a cool, dry and clean place beyond the access of children and people with limited

physical and mental abilities

Environmental protection

Old appliances contain valuable materials that can be recycled.

Please arrange for the proper recycling of old appliances. Please dispose your old appliances using

appropriate collection systems.

Subject to technical modications!

Inhaltsverzeichnis

Sprachen:

Andere Maestro Fleischwolf Handbücher

Maestro

Maestro MR853 Bedienungsanleitung

Beliebte Fleischwolf Handbücher anderer Marken

Klarstein

Klarstein Mett Max Bedienungsanleitung

Grizzly

Grizzly H7778 Bedienungsanleitung

Hobart

Hobart 4822 Bedienungsanleitung

Tasin

Tasin TS-108 Bedienungsanleitung

Adler Europe

Adler Europe AD 48 Bedienungsanleitung

camry

camry CR 4802 Bedienungsanleitung

Bake Max

Bake Max BMMG001 Bedienungsanleitung

Lumme

Lumme LU-MG2113A Bedienungsanleitung

Weston

Weston 35-3201 Bedienungsanleitung

Lumme

Lumme LU-2101 Bedienungsanleitung

GoWISE USA

GoWISE USA GW88012 Bedienungsanleitung

MPM

MPM MMM-07M Bedienungsanleitung

Weston

Weston 82-0101-W Bedienungsanleitung

BIRO

BIRO 3334SS Service-Handbuch

HOFFEN

HOFFEN MG-0440 Bedienungsanleitung

Scarlett

Scarlett SC-MG45M18 Bedienungsanleitung

Adcraft

Adcraft MG-1 Bedienungsanleitung

Johnson

Johnson tomit Bedienungsanleitung