Magnetrol Solitel Bedienungsanleitung

Installation and Operating Manual

Solitel

Vibrating

Rod Level

Switch

Read this Manual Befo e Installing

This manual provid s information on th Solit l®

Vibrating Rod L v l Switch. It is important that all

instructions ar r ad car fully and follow d in s qu nc .

D tail d instructions ar includ d in th Complete

Installation s ction of this manual.

Conventions Used in this Manual

C rtain conv ntions ar us d in this manual to conv y

sp cific typ s of information. G n ral t chnical mat rial,

support data, and saf ty information ar pr s nt d in

narrativ form. Th following styl s ar us d for not s,

cautions, and warnings.

Notes

Not s contain information that augm nts or clarifi s

an op rating st p. Not s do not normally contain

actions. Th y follow th proc dural st ps to which

th y r f r.

Cautions

Cautions al rt th t chnician to sp cial conditions that

could injur p rsonn l, damag quipm nt, or r duc

a compon nt’s m chanical int grity. Cautions ar also

us d to al rt th t chnician to unsaf practic s or th

n d for sp cial prot ctiv quipm nt or sp cific

mat rials. In this manual, a caution box indicat s a

pot ntially hazardous situation which, if not avoid d,

may r sult in minor or mod rat injury.

Wa nings

Warnings id ntify pot ntially dang rous situations or

s rious hazards. In this manual, a warning indicat s an

immin ntly hazardous situation which, if not avoid d,

could r sult in s rious injury or d ath.

Safety Messages

Th Solit l syst m is rat d by th IEC for us in Cat gory

II, Pollution D gr 2 installations. Follow all standard

industry proc dur s for s rvicing l ctrical and comput r

quipm nt wh n working with or around high voltag .

Always shut off th pow r supply b for touching any

compon nts. Although high voltag is not pr s nt in this

syst m, it may b pr s nt in oth r syst ms.

El ctrical compon nts ar s nsitiv to l ctrostatic

discharg . To pr v nt quipm nt damag , obs rv saf ty

proc dur s wh n working with l ctrostatic s nsitiv

compon nts.

This d vic compli s with Part 15 of th FCC rul s.

Op ration is subj ct to th following two conditions: (1)

This d vic may not caus harmful int rf r nc , and (2)

This d vic must acc pt any int rf r nc r c iv d, includ-

ing int rf r nc that may caus und sirabl op ration.

Low Voltage Di ective

For us in Cat gory II installations. If quipm nt is us d

in a mann r not sp cifi d by manufactur r, prot ction

provid d by quipm nt may b impair d.

WARNING! Explosion hazard. Do not conn ct or

disconn ct quipm nt unl ss pow r has b n switch d off

or th ar a is known to b non-hazardous.

Notice of Copy ight and Limitations

MAGNETROL r s rv s th right to mak chang s to th

product d scrib d in this manual at any tim without

notic . MAGNETROL mak s no warranty with r sp ct

to th accuracy of th information in this manual.

Wa anty

All MAGNETROL l ctronic l v l and flow controls ar

warrant d fr of d f cts in mat rials or workmanship

for ight n months from th dat of original factory

shipm nt.

If r turn d within th warranty p riod; and, upon

factory insp ction of th control, th caus of th

claim is d t rmin d to b cov r d und r th warranty;

th n, MAGNETROL will r pair or r plac th control at

no cost to th purchas r (or own r) oth r than

transportation.

MAGNETROL shall not b liabl for misapplication,

labor claims, dir ct or cons qu ntial damag or xp ns

arising from th installation or us of quipm nt. Th r

ar no oth r warranti s xpr ss d or impli d, xc pt

sp cial writt n warranti s cov ring som MAGNETROL

products.

Quality Assu ance

Th quality assuranc syst m in plac at MAGNETROL

guarant s th high st l v l of quality throughout th

company. MAGNETROL is committ d to providing

full custom r satisfaction both in quality products and

quality s rvic .

Th MAGNETROL quality assuranc syst m is

r gist r d to ISO 9001 affirming its commitm nt to

known int rnational quality standards providing th

strong st assuranc of product/s rvic quality availabl .

1.0 Introduction

Th Solit l®Vibrating Rod L v l Switch provid s r liabl

l v l d t ction of bulk solids and powd rs. This compact,

int gral switch is suitabl for high or low l v l d t ction

in hopp rs and silos. It may also b us d for plugg d

chut d t ction.

Th rugg d, singl -pi c prob is suitabl for us in a

vari ty of powd rs or granular mat rials with a minimum

bulk d nsity of l ss than on pound p r cubic foot.

1.1 Principle of Operation

Th Solit l®rod vibrat s at a 350 Hz fr qu ncy. Wh n

m dia mak s contact with th rod, th vibration is damp-

n d. Th att nuation of th vibration is d t ct d by th

int gral mount l ctronics, changing th status of th r lay.

2.0 Installation

2.1 Unpacking

Unpack th instrum nt car fully. Mak sur all compo-

n nts hav b n r mov d from th packing mat rial.

Insp ct all compon nts for damag , and r port any

conc al d damag to th carri r within 24 hours.

Ch ck th cont nts of th carton, making sur it agr s

with th packing slip and th purchas ord r. V rify that

th mod l numb r imprint d on th nam plat match s

th numb r on th packing slip and th purchas ord r.

R port any discr panci s to th factory. Ch ck and r cord

th s rial numb r for futur r f r nc wh n ord ring parts.

Serial Number

2.2 Mounting

Prior to installation, it is r comm nd d that th unit b

calibrat d using a sampl of th m dia to b m asur d.

Refe to Calib ation, Section 2.5.

IMPORTANT: Handl th instrum nt with gr at car ,

sp cially th prob . Any impact on th prob can damag

th vibration syst m.

56-601 Solitel Vibrating Rod Level Switch

Figure 1

Th SOLITEL switch is mount d to th v ss l using a

11⁄2" NPT thr ad d conn ction.

• Ensur that th tip of th prob is locat d at th d sir d

switching point giving consid ration to th slop angl of

th mat rial.

• Th switch may b install d v rtically or horizontally

(at a downward angl ) as shown in Figur 1 on pag 3.

• Avoid mounting th s nsor in a r c ss wh r buildup

could damp n th vibration. S Figur 2.

• Do not cut or b nd th vibrating rod.

IMPORTANT: A d fl ction plat is r quir d wh n th

prob is xpos d to falling mat rial, collaps d arch, or, in th

cas of a low l v l switch, wh n th drag forc of th mpty-

ing mat rial xc d th sp cifications. Th d fl ctor can b

a baffl plat or angl iron (11⁄2" ×11⁄2" ×1⁄8") locat d 4 to

6 inch s abov th rod. S Figur 3.

Obs rv th sp cifications for b nding forc (F),

torqu (M), and pull forc (F) as indicat d b low:

S Figur 4.

Standard: F = 100 pounds (445 N)

M = 63 foot pounds (85 Nm)

Ext nd d Rigid: M = 63 foot pounds (85 Nm)

Wh n using an xt nd d l ngth v rsion for low l v l

alarm, mount th prob abov th outl t of th v ss l to

avoid th prob b ing dragg d along by th outflowing

mat rial.

2.3 Electrostatic Discharge (ESD)

Handling Procedure

MAGNETROL l ctronic instrum nts ar manufactur d

to th high st quality standards. Th s instrum nts utiliz

l ctronic compon nts which may b damag d by static

l ctricity pr s nt in most work nvironm nts. Th

following st ps ar r comm nd d to r duc th risk of

compon nt failur du to l ctrostatic discharg :

1. Ship and stor circuit boards in anti-static bags. If an

anti-static bag is not availabl , wrap board in aluminum

foil. Do not plac boards on foam packing mat rials.

456-601 Solitel Vibrating Rod Level Switch

Figure 2

Figure 3

VXH VXR VXK

Figure 4

2. Use a grounding wrist strap when installing and

removing circuit boards. A grounded workstation is

also recommended.

3. Handle printed circuit boards only by the edges. Do not

touch components or connector pins.

4. Ensure that all electrical connections are completely made

and none are partial or floating. Ground all equipment to

a good earth ground wiring.

2.4 Wiring

Manually position the housing in the correct direction to

allow for easy wiring. The housing can rotate one full turn.

1. Make sure the power supply is turned off.

2. Unscrew and remove housing cover.

3. Connect power leads to the proper terminals. To simplify

wiring, the terminal strips may be removed from the

module by lifting the front edge of the terminal block.

Refer to Figure 5.

a. 120 VAC – Connect the “hot” wire to terminal marked

L1 and the “neutral” to terminal L2/N. There is no con-

nection to the center terminal.

b. 24 VDC – Connect wires to terminals (+) and (-). There

is no connection to the center terminal.

4. To ensure optimum noise immunity, attach the ground

wire to the green grounding screw inside the housing base.

Caution: On 4 VDC units, the negative terminal of the power

supply is isolated from ground and proper earth grounding

of the power supply shield wire is necessary for noise

immunity.

5. Connect relay terminals. Refer to Figure 6.

6. Set the fail-safe umper as described in the table on page 6.

For alarm applications, it is recommended that the

de-energized status of the relay be used as the alarm status.

This allows detection of power failure as an alarm status.

7. Wiring is complete. Replace the housing cover.

8. Apply power to the unit.

56-601 Solitel Vibrating Rod Level Switch

Figure 6

L1(+) No Connection L2/N(-)

Power

LED

Fail safe jumper

Sensitivity

adjustment

NO CO NC

Relay

Figure 5

2.5 Calibration

Ensur that th fail-saf jump r is install d in th prop r

position as d scrib d in Tabl 1. Th LED will show

r d wh n in alarm condition and gr n wh n in normal

condition. T st th op ration of th switch by holding,

and th n r l asing th vibrating rod; th LED will

chang color.

Th s nsitivity of th switch can b chang d using th

d nsity adjustm nt scr w. Not that this adjustm nt scr w

has 270 d gr s of rotation. Do not rotat past th stops.

NOTE: If the adjustment is too sensitive, the switch may detect

even slight residue of material rather than level.

Prior to installation, it is r comm nd d that th unit b

calibrat d using a sampl of th m dia to b m asur d.

656-601 Solitel Vibrating Rod Level Switch

Power Material Level Fail-Safe Jumper LED Color Relay Coil Relay Terminal

NO to CO NC to CO

6–7 7–8

On High A position Green De-energized Open Closed

B position Red Energized Closed Open

On Low A position Red Energized Closed Open

B position Green De-energized Open Closed

Fail High/Low A/B De-energized Open Closed

3.0 Reference Information

3.1 Troubleshooting

SOLITEL is a simpl and r liabl d vic . How v r, car

must b tak n to avoid impacting or damaging th vibrat-

ing prob .

In th v nt th SOLITEL stops vibrating, th following

proc dur will id ntify if th probl m is with th l ctron-

ic modul or with th s nsor:

Disconn ct th wir s going to th s nsor. (T rminals 3, 4,

and 5). Th following giv s th xp ct d voltag rang

b tw n th s nsors.

If th s voltag r adings ar not obtain d, th l ctronics

ar d f ctiv and n d to b r plac d. If th s voltag s ar

m asur d, th probl m is with th s nsor.

NOTE: The probe and electronics must be matched to ensure

proper operation. Use the following procedure to match

the electronics and the vibrating probe:

1. Conn ct th wir s from th s nsor to t rminals 3, 4, 5.

Th r will b two wir s of th sam color and on wir of

diff r nt color. Th two similar wir s go to t rminals 4 and

5; th singl wir go s to t rminal 3.

2. If th pot ntiom t r is lab l d “d nsity” turn to th low

position – if lab l d “s nsitivity” turn to th high position.

Not this pot ntiom t r has a 270 d gr turn.

3. Apply pow r to th l ctronic modul .

4. Turn th l ctronic modul ov r.

56-601 Solitel Vibrating Rod Level Switch

Terminals Voltage

3 and 4 4 to 6 VDC

3 and 5 0.3 to 1.0 VAC

Figure 7

Front Rear

5. Connect a digital multimeter between points MP5 on the

back of the module and ground connection terminal 3 on

the electronic module) or the body of the vibrating probe.

See Figure 7 on page 7.

6. Adjust potentiometer P2 on the rear of the electronic mod-

ule to obtain a voltage between 0.4 volts and 1.0 volts. The

reading should be as close to 1.0 volt as possible.

7. Grasp the vibrating section of the sensor with your hand.

The vibration should stop and the relay will change state.

8. Remove your hand from the sensor. The relay will

change state.

9. The electronic module and probe are now matched.

3.2 Agency Approvals

3.2.1 CSA

Model Approval

VXX-D1BX-XXX Class I, D v. 2

Groups A, B, C, & D

Class II, D v. 1

Groups E, F, & G

Type 4X

3.3 Replacement Parts

Item Description Part Number

1 Base 004-9189-001

2 Cover 004-9105-001

3 Cover o-r ng 012-2101-345

4 Electron cs module:

110 VAC Z30-9011-001

24 VDC Z30-9011-004

5 Bracket 005-6680-001

6 Probe o-r ng 012-2408-001

7 Snap r ng 010-5138-001

8 Sleeve 004-0111-001

9 Probe Consult Factory

856-601 Sol tel V brat ng Rod Level Sw tch

These un ts have been tested to EN 50081-2

and EN 50082-2 and are n compl ance w th

the EMC D rect ve 89/336/EEC.

These un ts have been evaluated to the

appl cable UL and CSA standards. CSA s

accred ted as a NRTL (Nat onal Recogn zed

Test ng Laboratory) n the Un ted States.

NRTL/C

➁

➀

➂

➃

➄

➅

➆

➇

➈

3.4 Specifications

3.4.1 Performance

Description Specification

Input voltage 110 VAC +10/-15%

24 VDC (±10%)

Powe consumption L ss than or qual to 3 VA

Ope ation f equency 350 Hz

Output elay SPDT 8 amp @ 250 VAC

SPDT 1 amp @ 24 VDC

Time delay 6–10 s conds

(d p nding on d nsity adjustm nt)

P ocess connection 11⁄2" NPT

Housing NEMA 4X

Ope ating p ocess conditions

Standa d -4 to +230 °F

(-20 to +110 °C)

Enhanced pe fo mance -40 to +320 °F

(-40 C to +160 °C)

Ambient elect onics temp. -40 to +140 °F, s chart at l ft

(-40 to +60 °C)

Relative humidity 98%

Maximum p ocess p essu e 360 psig

Minimum Density 50 oz/ft3or 0.05 gm/cm3

Mate ials specifications

Vib ating od 316 stainl ss st l

Rigid extension 316 stainl ss st l

Inse tion length

VXH 8.25 inch s (209 mm)

VXR 10 to 100 inch s (25 to 254 cm)

Maximum mechanical load on p obe

St anded p obe 63 Ft/lbs. (85 Nm)

Extended igid p obe 63 Ft/lbs. (85 Nm)

56-601 Solitel Vibrating Rod Level Switch

-40 F

(-40 C)

-40 F

(-40 C)

140 F

(60 C)

95 F

(35 C)

167 F

(75 C)

320 F

(160 C)

Process Temp.

Ambient Temp.

10 56-601 Solitel Vibrating Rod Level Switch

Standard Length

DIMENSIONAL SPECIFICATIONS inches (mm)

1.73 (44) Dia.

6.34

(161)

Insertion

length

8.25

(209)

3.44 (87)

Rotation clearance

11/2" NPT

process connection

3/4" NPT

Conduit connection

2.75

(69)

4.63

(117) Dia.

3.63

(92)

3/4" NPT

plugged

1.5

(38)

3.4.2 Physical

Extended Rigid Probe

1.73

(44) Dia

6.34

(161)

Insertion

length

11/2" NPT

process connection

3.44 (87)

Rotation

clearance

3/4" NPT

Conduit

connection

2.75 (69)

4.63

(117) Dia.

3.63

(92)

1.5

(38)

3/4" NPT

plugged

Inhaltsverzeichnis

Andere Magnetrol Controller Handbücher

Magnetrol

Magnetrol Tuffy Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung