MakeKit MD2 Dronekit Bedienungsanleitung
1
Teacher and student guide
MD2 Dronekit
Start by studying the safety information on the next page. Propellers
can cause damage and must therefore be distributed at the end.
Paper propellers are used temporarily to test that the motors are
going in the right direction.
2
Construction plan:
There are four main areas, which should be done in this order:
assembly, electrical connections, programming and flying. !
You are welcome to delegate the four tasks to different students,
who are each given their own main responsibility, which they can
later roll on (especially the flight).!
Once the drone is built and the electrical connection is made, check
the following before getting the battery:!
Layout, page 8. Silver motor in the right place. Two different colors
of propeller protectors, one at the front and another at the rear.
(Color may vary).!
Wiring diagram, page 15. It is especially important not to switch
between + and - between ESC (speed controllers) and power
distribution boards, as well as not to change the battery measuring
cable and speaker cable.!
Charge the batteries. Put the battery in the
enclosed charging bag. All lights should be
green before charging is complete after 1-2
hours.!
Insert 4 AA batteries into the radio. We
recommend rechargeable batteries for the sake
of the environment.!
The drone flies for 11-13 minutes on one battery.!
Reset the drone's control card by selecting
“factory reset” which is located at the very
bottom of the menu.!
•When they have finished programming, you or students
(other than those who have programmed) should check the
following:!
•The paper propellers should rotate straight in accordance
with the layout, page 8.!
•Review receiver test, page 18. Check that the movements of
the connectors are correctly reflected on the screen. Throttle
= gas, left stick down = 0, up = about 100!
•Yaw (rudder) = side rotation, left stick to the right / left results
in “rudder left / right” +/- about 100!
•Pitch (elevator), right stick forwards or backwards, +/-
approx. 100!
•Roll (aileron), right stitch to the side, +/- approx. 100!
•Check that all wires and components are attached correctly
and that no wires or antenna can be cut by the propellers.!
•Once this has been checked, you can distribute the
propellers. It is important to distinguish between up and
down, as well as right- and left-rotating propellers. See page
9. Make students aware of the dangers associated with
propellers.!
Flight:
The pilot and the rest of the team take the drone to a suitable
flight area. Gym or other open space indoors is the safest and
is unregulated by FAA and aviation authorities. Avoid third
persons entering the flight area and especially smalle children
must be kept at a safe distance. Low ceiling height can also be
an advantage as you can not crash from a great height.!
Outdoors, large grass pitches are the best place to fly as it is
open, and the surface is soft and damages the drone less in the
event of a crash. Provide the required safety distance to
outsiders. Check local rules regarding flight outdoors.
Tools:
1.5mm Allen or Torx. Star puller medium size. Scissors if you
want to cut out paper propellers.!
To the teacher
PROPELL
BATTERI
ARMERING
When the drone is armed* and the propellers are
mounted.!
you must have at least 2 meters safety distance to
the nearest person.!
*Arming: The drone is activated and the propellers
can spin. Characteristics: Red light on control card,
it says "ARMED" in the display.!
The drone battery (LiPo), can develop heat and toxic
fumes if it is severely damaged. It the batteri suddenly
inflates or starts to extract smoke, get the battery outside
the premises, and away from people as quickly as
possible. !
Have a plan for this in advance.
Rule 1:
Rule 2:
3
Propeller hazard
The propellers rotate at up to 28,000 rpm. minute.
Show respect for the forces and damage potential of
the propellers when the drone has battery connected.!
Keep the required safety distance when the drone is
armed.
Aviation rules
When flying outdoors, make sure to follow local drone
rules. Keep a safe distance so as not to endanger other
people.
It is not recommended to fly this drone higher than the
roof of the nearest building and no more than 30
meters away from yourself. This will help you retain
control of the drone.
Safety
Deleliste - Ramme
Bottom plate Motor holders,
4x
Nylonnuts,
4x
Nylonskruer,
4 stk
Velcros, 4x o-rings:
8x
Top plate
Protection hoops
upper / lower part
Landing legs Battery strap
Arm pieces,
type A and B, 4 of each
Avstandsstykker,
8 stk
4
Deleliste - Elektronikk
1 x
3 cell LiPo-battery
2+2 1806 2300 kv
brusless motors, CW and
CCW type
1x Power distribution board 1 stk KK2 flight controller
4 servo cables
2+2 propeller, CW
and CCW type
(+4 spares)
1 stk fire proof LiPo
Charging bag
Piezo-speaker with cable
1 stk
Radio with receiver
5
4 x regulators
(ESC)
Receiver
6
Assembly
As assembly manager, your job is to make sure that all the parts are assembled together in
the right way. Use the attached drawings and get a couple of free hands from your team
members.!
You are responsible for all assembly except connection of wires, which is left to a
knowledgeable electrician when your job is done.!
What you need to do:!
•Get the necessary tools: Medium-sized Phillips screwdriver, 1.5mm Allen key, scissors!
•Follow the construction instructions. You will receive parts from the component manager as
you need them. Bring helpers with you, then it might go faster.
7
Layout Sort
motorhode
Black
motor
Silver
motor
Nose
direction
Control board to be
mounted this way!
Clock wise rotating
propeller
Counter clock wise
rotating propeller
Make sure:
You must have two identical colors
on the front of the propeller
protectors, and another color on the
back.!
This is to make the flight easier for
the pilot.!
You must place the black and silver
motor as shown in the picture. The
engines must go their separate ways.!
You must place the top plate as
shown in this picture. The control
board must be placed in the direction
shown here.!
The direction of the nose on the
drone is then to the north.!
Finally, you must mount the right
propeller in the right place. See next
page.
8
Clock wise rotating
propeller
Counter clock wise
rotating propeller
Black
motor
Silver
motor
Mounting the propeller
We recommend saving this part until everything else is mounted.
Always make sure that the battery is disconnected before mounting
the propeller!
Also, make sure that you have tested and adjusted the direction of
rotation so that they are correct.
Unscrew the bolts on top of the engine and place the propeller on the
screw.
Tighten the bolts again. They can be screwed with your fingers and
should not sit particularly hard. They tighten themselves during flight.
Silver motor head should be screwed the opposite way of black motor
head.
9
We have two types of propellers, right and left rotating. (Regardless of
color)
Right-rotating is marked R, eg 5030R. Install the propellers according
to the overview above.
The writing on the propellers is going up towards the sky.
5030R 5030 5030R 5030
Clockwise (CW)
Counter clockwise (CCW)
Counter clockwise (CCW)
Clockwise (CW)
Motors and arms
4
Temporarily thread a small rubber ring onto the
motor plate (1). Click the engine plate with armrest
type a and b (2) and the landing legs (3). Finally,
tighten the rubber ring (4).
Repeat for all four arms.
1
3
2
2
Senter plate
2
3
4
5
1
6
Tools: Star puller
Parts:
1 top plate
4 nylon screws
8 spacers
4 nylon nuts
1 control card
1 power distribution board
Note the location of the top plate,
with the holder for the receiver
located on the left (1) and the
holder for the buzzer (2).
Also note the location of the
power distribution board, with the
battery cable facing south (3)
and the thinner battery
measuring cable facing north
(not shown)
Screw the 8 spacers above and
below the top plate (4), fasten
the power distribution board with
4 nuts (5), and finally the control
board with 4 screws (6).
1
2
3
Tools: 1.5mm Allen wrench
Parts: 4 engine plates, 4 engines, 4 propeller
protectors, 8 arm pieces (two variants), 4 landing legs,
16 pcs 10mm m2 screws, 4 o-rings
Screw in all four engine screws through the engine
plate (1), the propeller guard (2) into the engine (3).
NOTE! The screws must pass through both the
engine plate and the propeller guard!
x4
x4
10
Inhaltsverzeichnis
Andere MakeKit Lehrmittel Handbücher
Beliebte Lehrmittel Handbücher anderer Marken
fischertechnik
fischertechnik STEM Coding Pro Bedienungsanleitung
Experia
Experia IRiS Light Wand Bedienungsanleitung
Pitsco Education
Pitsco Education FLO Bedienungsanleitung
Sphero
Sphero RVR RV01 Bedienungsanleitung
Limbs & Things
Limbs & Things 60905 Bedienungsanleitung
JP
JP TURN Connect T101 Bedienungsanleitung
TruCorp
TruCorp AirSim Advance Bedienungsanleitung
LeapFrog
LeapFrog Mr. Pencil's Scribble, Write & Read Bedienungsanleitung
ScienTECH
ScienTECH 2261 Bedienungsanleitung
Rompa
Rompa 20019 Bedienungsanleitung
Duinotech
Duinotech XC4322 Bedienungsanleitung
Enabling Devices
Enabling Devices Spinning Light Show Bedienungsanleitung