Makita DA330D Handbuch
Models No.
Description
PRODUCT
CONCEPT AND MAIN APPLICATIONS
P 1/ 10
DA330D/ DA331D
10.8V Cordless Angle Drill 10mm (3/8")
Specification
Standard equipment Optional accessories
Note: The standard equipment for the tool
shown above may vary by country.
Battery BL1013*2
Battery BL1014*3
Charger DC10WA*2
Charger DC10WB*3
Battery cover
Chuck key S10 (for DA330D only)
+ Bit 2-50
Plastic carrying case
Models DA330D/ DA331D have been developed
as the first 10.8V Li-ion cordless angle drills.
The compact angle head and its small center height allow easy access to
tight spaces where DC driver drills cannot do it.
The difference between these models are as follows;
DA330D/ equipped with Keyed drill chuck
DA331D/ equipped with Keyless drill chuck
Battery
Specification Model No.
No load speed: min.ˉ¹=rpm
Charging time (approx.): min.
Weight according to
EPTA-Procedure 01/2003*4: kg (lbs)
Capacity: Ah
Type of cell
Voltage: V
0 - 800
Max output: W 135
1.1 (2.4)
Energy capacity: Wh
Li-ion
DA330D DA331D
1.1 (2.5)
*2For all countries except North, Central and South American countries; however, DC10WA is supplied to Argentina.
*3For North, Central and South American countries except Argentina
*4with battery
Dimensions: mm (")
Width (W)
Height (H)
Length (L) 298 (11-3/4)
Model No. DA331D
52 (2-1/16)
77 (3)
310 (12-1/4)
52 (2-1/16)
88 (3-1/2)
DA330D
Driver bits
Socket bits
Drill bits for wood
Drill bits for steel
Battery BL1013*2
Battery BL1014*3
Charger DC10WA*2
Charger DC10WB*3
L
H
W
1.3
14
10.8*2, (10.8/12Vmax*3)
50 with DC10WA*2, (DW10WB*3)
Capacities: mm (") Steel
Wood
10 (3/8)
12 (1/2)
Capacity of drill chuck: mm (")
Drill chuck type
1.5 (1/16) - 10 (3/8) 0.8 (1/32) - 10 (3/8)
Keyed Keyless
Yes (single LED)
Reverse switch
LED job light
Yes
Yes
Yes
Electric brake
Variable speed control by trigger
DA330D
DA331D
L
HW
TECHNICAL INFORMATION
P 2/ 10
Repair
Apply Makita grease N No.2 to the following portions designated with the black triangle to protect parts and product
from unusual abrasion.
[1] NECESSARY REPAIRING TOOLS
CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
Code No. Description Use for
[2] LUBRICATION
Fig. 1
Item No. Description
Teeth portion for smooth engaging with Spiral bevel gear 6
Teeth portion for smooth engaging with Motor’s gear
AmountPortion to lubricate
Bearing plate (for arbor press)1R022
1R029
1R045
1R223
1R224
Bearing setting pipe 23-15.2
Gear extractor (large)
Torque wrench shaft 20-90N·m
Ratchet head 12.7 (for 1R223)
1R231
1R269
1R279
1R291
1R398
1/4” Hex. shank bit for M8
Bearing extractor
Round bar for Arbor 5-50
Retaining ring S and R pliers
Bearing retainer wrench
removing / assembling Spur gear 42 for DA330D
assembling Spur gear 42 for DA331D
removing Spur gear 42
removing / assembling Keyless drill chuck for DA331D
removing Ball Bearings
removing Gear shaft from Spur gear 42 for DA330D
removing Retaining Ring S-12
loosening / fastening Bearing retainer
DA331DDA330D
DC motor
20
20 4 g
2.5 g
a little
Spiral bevel gear 31
20
Lock ring for DA331D Inside where 6 Spur gear 42 contacts4
Spur gear 426
46
6
Spiral bevel gear 6Spiral bevel gear 6
DC motor
P 3/ 10
Fig. 2A
Drill chuck is factory assembled to Spindle to which Spiral bevel gear 31 is mounted. Consequently, it is impossible
to replace Drill chuck singly without removing Spiral bevel gear 31 from the Spindle portion of Drill chuck.
Disassemble Drill chuck section as drawn in Fig. 2A.
Cloth or something soft
1R398
Note in Disassemble:
When removing Bearing retainer 36-43,
turn 1R398 with a screwdriver or something like
with pressing 1R398 firmly.
1. Set the machine to vise with a cloth or something soft
to protect the machine, then remove Bearing retainer
36-43 by turning it clockwise with 1R398.
2. Disassemble Drill chuck section
by tapping the edge of Gear housing
with a plastic hammer.
3. Remove Ball bearing 608ZZ with 1R269, and remove
Retaining ring S-12 with 1R291.
Then, Spiral bevel gear 31 is removed from Drill chuck.
Note: Be careful not to lose Key 4.
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -1A. Drill Chuck and Spiral bevel gear 31 for DA330D
Bearing retainer 36-43
Ball bearing
608ZZ
Retaining
ring S-12
Ball bearing
6806DDW
Pins
3A. If it is difficult to remove Spiral bevel gear 31
by hand, remove the gear with 1R045.
It is possible to remove the gear together with
Spiral bevel gear 31 using with 1R045.
In this case, make sure that three Jaws are
exactly closed before setting 1R045.
4. Spiral bevel gear 31 and Ball bearing 6806DDW
are removed from Drill chuck S-10.
Note: Be careful not to lose Key 4.
Key 4
Spiral bevel
gear 31
Spiral bevel gear 31
three Jaws
Note in Disassemble:
In case three jaws of the drill chuck is not closed
completely, Pins interfere with Ball bearing
6806DDW.
Ball bearing
6806DDW
Drill chuck S-10
DISASSEMBLING
Key 4
Spiral bevel gear 31
P 4/ 10
Fig. 2B
Disassemble Drill chuck section as drawn in Fig. 2B.
(1) Preset the fastening torque of 1R223 to 40 - 45 N·m.
(2) Assemble Drill chuck by reversing the disassembly procedure. (Refer to the illustrations in Fig. 2B)
(1) Disassemble Keyless drill chuck as drawn in Fig. 2B.
(2) Disassemble Bearing retainer 36-43 as drawn in Fig. 3.
1. Assemble the repairing tool by attaching
1R231, 1R224 and Bit adapter to 1R223.
2. Grip 1R231 with Drill chuck, then remove Drill chuck
by turning the repairing tool counterclockwise.
Repair
[3] -1B. Drill Chuck for DA331D (equipped with Keyless Drill Chuck)
[3] -2. Spiral bevel gear 31 for DA331D
1R223
1R224 1R231
Bit adapter
DISASSEMBLING
DISASSEMBLING
ASSEMBLING
Fig. 3
1R398
Cloth or something soft
Bearing retainer 36-43
Assemble Drill chuck section by reversing the disassembly procedure. (Refer to the illustrations in Fig. 2A)
Note in Assembling 1:
Close the three Jaws for easy assembling Ball bearing 6806DDW.
Note in Assembling 2:
Do not forget to mount Key 4 to the groove on Spindle of Drill chuck, and mount Spiral bevel gear 31 to Spindle
while aligning the notch of Spiral bevel gear 31 to Key 4.
ASSEMBLING
[3] DISASSEMBLY/ASSEMBLY
[3] -1A. Drill Chuck and Spiral bevel gear 31 for DA330D (cont.)
1. Set the machine to vise with a cloth or something soft
to protect the machine, then remove Bearing retainer
36-43 by turning it clockwise with 1R398.
Note in Disassemble:
When removing Bearing retainer 36-43,
turn 1R398 with a screwdriver or something like
with pressing 1R398 firmly.
P 5/ 10
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -2. Spiral bevel gear 31 for DA331D (cont.)
DISASSEMBLING
ASSEMBLING
Assemble Spiral bevel gear 31 by reversing the disassembly procedure. (Refer to Figs. 4, 3 and 2B)
Fig. 4
2. Disassemble the gear section
by tapping the edge of Gear
housing with a plastic hammer.
Spindle
Bearing box
Spiral bevel
gear 31
Retaining ring S-12
Key 4
Retaining ring S-12
Ball bearing 608ZZ
3. Bearing box can be removed by hand. Remove Ball bearing 608ZZ
with 1R269, and remove Retaining ring S-12 with 1R291. Then,
Spiral bevel gear 31 is removed by hand. If it is difficult to remove
the gear by hand, remove it with 1R045.
Note: Be careful not to lose Key 4.
(3) Disassemble Gear section as drawn in Fig. 4.
Gear section
P 6/ 10
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -3A. Spiral bevel gear 6 and Spur gear 42 for DA330D
DISASSEMBLING
1. Remove Key holder from
Housing set.
2. Remove Set plates from Housing set
with small slotted screwdriver.
3. Remove Housing R
by unscrewing seven
3x16 Tapping screws.
4. Separate Gear housing section. 5. Remove Spur gear 42 together
with Spiral bevel gear 6 by tapping
Gear housing with a plastic hammer.
Spur gear 42 and
Spiral bevel gear 6
Housing R
(1) Take out Spiral bevel gear 6 and Spur gear 42 as drawn in Fig. 5.
(2) Remove spiral bevel gear 6 as drawn in Fig. 6.
Fig. 5
Fig. 6
Key holder Set plate (2pcs.)
Gear housing
1R022
Ball bearing
696ZZ
1. Insert a set of 1R022 between Spur gear 42 and Ball bearing 608ZZ. Then, push Ball bearing 696ZZ
with Arbor press to seat the bearing on Spur gear 42.
2. Remove Spur gear 42 and Ball bearing 696ZZ using 1R279 and Arbor press. Ball bearing 608ZZ
remains on Spiral bevel gear 6 after this process. The bearing is removed with 1R269.
Ball bearing 608ZZ
1R022
Spur gear 42
Spur gear 42
Spiral bevel gear 6
Ball bearing 696ZZ Ball bearing 608ZZ
1R022
1R279
Spiral bevel gear 6
P 7/ 10
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -3A. Spiral bevel gear 6 and Spur gear 42 for DA330D (cont.)
[3] -3B Spiral bevel gear 6 and Spur gear 42 for DA331D
DISASSEMBLING
(1) Take out Gear housing in the same way as DA330D. (See Fig. 5)
(2) Disassemble Spiral bevel gear 6 and Spur gear 42 as drawn in Fig. 8.
Fig. 8
Fig. 7
3-1. Find out Ring spring’s cut portion
at the grooved portion of Spline,
insert a pricker under Ring spring
at the near point of the cut portion.
3-2. Remove Ring spring with the pricker
as drawn below.
1. Tap the edge of Gear housing
with a plastic hammer
to remove Gear section
from Gear housing.
4. Strike Gear section to work bench to separate
Spiral bevel gear 6 from Spur gear 42.
2. Remove Ball bearing
696ZZ with 1R269.
3. Remove Ring spring 6 with a pricker as drawn right.
Spiral bevel gear 6
Ball bearing 608ZZ
Gear section
ASSEMBLING
Assemble the gear section by reversing the disassembly procedure. (Refer to Figs. 6 and 5)
Note: Spur gear 42 has to be assembled as drawn in Fig. 7.
Stepped side
Assemble Spur gear 42 while facing its stepped side
to Ball bearing 608ZZ.
Ball bearing 608ZZ
Spur gear 42
Lock cam
Pin 3.5
Pin 3.5
Lock ring
5. Gear section can be disassembled as follows.
P 8/ 10
Repair
[3] DISASSEMBLY/ASSEMBLY
[3] -3B Spiral bevel gear 6 and Spur gear 42 for DA331D
[3] -4 F/R Change Lever of Switch
ASSEMBLING
Mount F/R change lever to Switch as drawn in Fig. 11.
(1) Assemble Spiral bevel gear 6 to Spur gear 42 as drawn in Fig. 9.
(2) Assemble Gear section to Gear housing as drawn in Fig. 10.
Fig. 11
Fig. 9
Fig. 10
F/R change lever
Set F/R change lever to Switch with aligning
the cavity portion with the boss of Switch.
Cavity portion
Boss
Switch
1R029
Projection
(both side of Lock ring)
While fitting Projection of Lock ring
to the cut portion of Gear housing,
push Gear section into Gear housing
with 1R029 until it stops.
Cut portion of Gear housing
Cut portion of Gear housing
Spiral bevel gear 6
Ball bearing 608ZZ
Pin 3.5
Spur gear 42
Lock ring
Ball bearing 696ZZ
Lock ring Ring spring 6
ASSEMBLING
Circuit diagram
Wiring diagram
P 9/ 10
Fig. D-1
Fig. D-2
Fig. D-3 Fig. D-4
Wiring to Electrical parts
White
Color index of lead wires' sheath
Switch DC Motor
Black
Terminal
Terminal
Switch
TerminalReceptacle
Receptacle
Connect Receptacle of Lead wire
(black) to minus terminal while facing
its wire connecting portion to
plus terminal side.
Connector
LED Light
circuit
B+
B-
M+
M-
M2
M1
Red
Note: Circuit diagram of Switch and DC motor as drawn below is
the view from Housing set (L) side.
M1
M2
M+
Red mark
M-
Receptacles have to be connected to DC Motor
that Lead wires come to Housing L side when
the motor is mounted to Housing L.
DC Motor
Connect Receptacle of Lead wire
(red) to plus terminal while facing
its wire connecting portion to
minus terminal side.
Connect Receptacles of Lead wires
while facing their wire connecting
portions to DC motor side.
Be careful not to put these Lead wires
on or over Rib A and Boss A.
Wiring diagram
P 10/ 10
Fig. D-5
Fig. D-6
Wiring of Lead wires of LED Light circuit
(before setting Switch)
Wiring in Housing set (L)
(After setting Switch and DC Motor)
Connector
Lead wire holder
Lead wires have to be fixed
with Lead wire holders.
Lead wire holder
Lead wire holder
Boss A
Rib A
Terminal Rib B Rib C
Rib D
LED Light circuit
Set LED Light circuit to
Housing set (L) while
facing Circuit plate to
DC motor side.
Projection
of Adhesive
Circuit plate
DC motor
side
Boss B Red mark
DC Motor
Inflect (+) Terminal of DC motor so that
the terminal can be located between
Boss B and Rib C.
Inflect (-) Terminal of DC motor so that
the terminal can be located between
Rib C and Rib D.
Switch
Put Lead wire (red) between Rib B
and Switch.
Be careful not to put this wire (red)
on or over Rib B.
Put the slag of Lead wire (red) between
Rib C and Switch as drawn above.
Put the slag portion of Lead wires
to this place (about under Switch).
Andere Handbücher für DA330D
6
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Makita Bohren Handbücher
Makita
Makita DDF484RFE Bedienungsanleitung
Makita
Makita HP330D Bedienungsanleitung
Makita
Makita HP2030 Bedienungsanleitung
Makita
Makita DP3002 Bedienungsanleitung
Makita
Makita HP0300 Bedienungsanleitung
Makita
Makita 6207D Bedienungsanleitung
Makita
Makita BDF459 Bedienungsanleitung
Makita
Makita DA330D Handbuch
Makita
Makita DHP484ZJ Bedienungsanleitung
Makita
Makita DA391D Bedienungsanleitung
Makita
Makita BDF460 Bedienungsanleitung
Makita
Makita 8419B Bedienungsanleitung
Makita
Makita DS4012 Handbuch
Makita
Makita HP2050 Bedienungsanleitung
Makita
Makita 6409 Bedienungsanleitung
Makita
Makita DA333D Bedienungsanleitung
Makita
Makita BHP460 Bedienungsanleitung
Makita
Makita 6411 Handbuch
Makita
Makita 6313D Bedienungsanleitung
Makita
Makita 6305 Bedienungsanleitung
