Makita BTD200 Handbuch

Models No.

Description

PRODUCT

TECHNICAL INFORMATION

CONCEPTION AND MAIN APPLICATIONS

Specification

Optional accessories

P 1 / 4

Dimensions : mm ( " )

Width ( W )

Height ( H )

Length ( L )

86 (3-3/8)

277 (10-7/8)

232 (9-1/8)

No load speed

(min-1=rpm)

Voltage (V)

Capacities

Impact per minute

(min-1=bpm)

Driving shank : mm ( " )

Net weight: kg (lbs)

D/C 24 V

Wood screws

Self tapping screws

High speed

Low speed

High speed

Low speed

0 - 2,000

0 - 1,600

0 - 3,000

0 - 2,500

6.35 ( 1/4 ) Hex

* 2.9 (6.3 lbs)

* 2.9 (6.3 lbs) : including the weight of battery 2417 / 1.7Ah.

Hex screws

6 mm (1/4)

* Philips bits 2-34, 2-65, 2-82, 2-110, 2-150, 2-250, 3-45, 3-65, 3-110

* Socket bit 8-55, 3/8"-55,

* Bit piece

* Shoulder strap

* Battery B2417, B2430

* Charger DC24SA

Model No. No.

B2417

Battery

Type Charger

Q'ty

BTD200SH

BTD200SF Ni-MH 1.7 1 pc. DC24SA

B2430 3.0 1 pc.

BTD200

Cordless Impact Driver

BTD200 is equipped with newly developed 24 V Ni-MH battery.

The method of speed change is electric 2 speed + variable speed change.

The max. fastening torque of 200 N.m (2,040Kgf.cm / 1,770in.lbs)

is suitable especially for tightening the wood screws of long size.

The variation of this model is as listed blow.

Charging time

with DC24SA

Model BTD200SH

Model BTD200SF

** approx. 30 minutes

** approx. 60 minutes

** approx. 30 minutes / ** approx. 60 minutes : The figures left mentioned may be change depending

on the conditions of battery, room temperature, charger,

etc.

Repair P 2 / 4

<1> Disassembling housing R and L

Take off bumper from housing with hand.

Dismount hammer case from housing by taking off

4 hex socket head bolts M5x35, and disassemble

housing R and L as illustrated in Fig. 1.

<2> Disassembling bit holder section

Take off ring spring 12 from the groove on anvil.

Then flat washer 4, compression spring 14 and sleeve

can be removed from anvil by pulling them in the

direction of the arrow in Fig.2.

Anvil can be separated from hammer case after

disassembling sleeve section.

Hex socket

head bolts M5x35

Hammer case

Housing R

Housing L

Fig. 1

Bumper

Ring

spring 12 Flat

washer 4

Compression

spring 14

Sleeve Anvil

Steel ball 4.0 x 2pcs.

Hammer case

Pull out in this direction

Fig. 2

<3> Apply 0.5g of MAKITA grease N No.2 on the

cylindric part of anvil, when inserting it into

hammer case.

Apply MAKITA grease N No.2

Fig. 3

<4> Disassembling hammer section

(1) Grip the hammer section with large gear extracter No.1R045

as illustrated in Fig. 4.

Press spindle to hammer by turning the handle clock-wise

until it stops.

Anvil

Fig. 4

1R165 Ring spring

setting tool B

Flat plate Turn the handle

clock-wise

Spindle

Hamer

Compression spring 14

No.1R045

Large gear extracter

Ball bearing 6002LLB

Repair P 3 / 4

(2)Adjust the opening for steel ball inserting, to the cam groove top of spindle

as illustrated in Fig. 5.

Spindle

Cam groove top

of spindle

Opening for steel

ball inserting

Steel ball 5.6 x 2pcs.

Steel ball 4 x 25pcs.

Hammer

(3)Take off 2 steel balls 5.6 with magnetic bar or tweezers from spindle.

(4)Loosen the handle of 1R045 turning it anti-clockwise

and remove hammer from spindle.

(5)When assembling, adjust the "opening for steel ball inserting", to the "cam groove top" of spindle

and insert steel ball 4 into hammer as illustrated in Fig. 5.

< Note > Set the hammer as illustrated in Fig.5A,

when removing it from spindle.

Otherwise steel balls 4

will fall off hammer.

Ball bearing

6002LLB

1R165 Ring spring

setting tool B

Fig. 5

Fig. 5A

(6) Apply MAKITA grease N No.2 in small volume to the position marked with black triangle mark.

See Fig. 6.

(1) Spindle

(3) Steel ball 5.6 x 2

(2) Steel ball 4 x 25pcs. Hammer

(4) Spur gear 24

Fig. 6

Bottom view of spindle

Apply MAKITA grease N No.2 in small volume

into the hole of spindle.

Circuit diagram

Wiring diagram

P 4 / 4

Terminal

Speed Change

Switch

FET

Bruch Holder

Brush Holder

M2 M1

Red

Black White

Black

Orange

Brush holder lead wire

(Black)

Brush holder lead wire

(Red)

Speed change switch

Lead wire of speed change

switch (white) must not be

loosen in this area.

Fix lead wire of speed change

switch (white) with lead holder.

Lead wires of speed change

switch (black and white)

must not be loosen in this area.

Fix the following lead wires

with lead holder.

1 Switch lead wire (Orange) to be

connected to terminal

2 Switch lead wire (Black) to be

connected to terminal

3 Lead wires of speed change switch

(Black and White)

The above lead wires have to be fixed

with lead holder as illustrated in the

following Fig.

Switch side

Terminal side

12 3

Lead

holder

Terminal

Andere Handbücher für BTD200

Andere Makita Impact Driver Handbücher

Makita

Makita TW1000 Bedienungsanleitung

Makita

Makita BTP130 Bedienungsanleitung

Makita

Makita TD022D Bedienungsanleitung

Makita

Makita DTW1001 Bedienungsanleitung

Makita

Makita DTD137 Bedienungsanleitung

Makita

Makita XT328M Bedienungsanleitung

Makita

Makita 6905B Kurzanleitung

Makita

Makita 6905B Bedienungsanleitung

Makita

Makita TW0350 Handbuch

Makita

Makita LT02Z Bedienungsanleitung

Makita

Makita TD090D Bedienungsanleitung

Makita

Makita BTP131RFE Bedienungsanleitung

Makita

Makita TD021 Bedienungsanleitung

Makita

Makita BTD129 Bedienungsanleitung

Makita

Makita TD090D Bedienungsanleitung

Makita

Makita TD0101 Bedienungsanleitung

Makita

Makita tw0250 Handbuch

Makita

Makita DTD156ZJ Bedienungsanleitung

Makita

Makita 6704D Bedienungsanleitung

Makita

Makita TW1000 Bedienungsanleitung

Makita

Makita TD126D Bedienungsanleitung

Makita

Makita DTD155Y1J Bedienungsanleitung

Makita

Makita TW141DWME Bedienungsanleitung

Makita

Makita TD110D Bedienungsanleitung

Beliebte Impact Driver Handbücher anderer Marken

stayer

stayer IW500D Bedienungsanleitung

Milwaukee

Milwaukee M12 FID Bedienungsanleitung

Grizzly

Grizzly H6140 Bedienungsanleitung

Ozito

Ozito LID-3000 Bedienungsanleitung

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Bedienungsanleitung

Greenlee

Greenlee HW3 Bedienungsanleitung

Sthor

Sthor 57091 Bedienungsanleitung

Hilti

Hilti SIW 2-A12 Bedienungsanleitung

Ryobi

Ryobi R18IW3 Bedienungsanleitung

Parkside

Parkside PDSSA 20-Li A1 Bedienungsanleitung

Flex

Flex FX1471 Bedienungsanleitung

SATA

SATA 51075C Technisches Handbuch

Cembre

Cembre NR-11P Bedienungsanleitung

DeWalt

DeWalt XR Li-ion DCF902 Bedienungsanleitung

Stanley

Stanley FATMAX SBI810 Bedienungsanleitung

Sealey

Sealey CP650LIHV Bedienungsanleitung

Sunex Tools

Sunex Tools SX505A-8 Bedienungsanleitung

Facom

Facom NJ.1400F 826558 Bedienungsanleitung