Makita EM2600L Bedienungsanleitung
SERVICE MANUAL
EM2600U,EM2600L
ER2600L
[Image: EM2600U] [Image: EM2600L]
[Image: ER2600L]
SPECIFICATIONS
Specifications
Model
EM2600U
EM2600L
Dimensions (mm)(L x W x H)
(without cutting blade)
1770x 610 x 410 1770x 330 x185
Weight (kg)
5
Revolution of cutter head(rpm) 4,000~6,000
Gear ratio
14/19
Clutch
Automatic centrifugal type
Engine
1E33F
Displacement (cm3
) 25.7
Power rating (kw)
0.8
Carburetor All position diaphragm type
Starting system Recoil starter
Ignition system Solid state ignition
Plug
NGK BPMR7A or equivalent
tank (l) 0.6
Fuel Mixed gas (Gasoline: Makita Genuine Two-stroke Engine Oil=50:1)
NOTE:
▪
Specifications are subject to change without notice.
Designation of parts
Disassembly of Nylon Cord Assembly for ER2600L
Unscrew 2 CROSSRECESS BOLT M6X30 (115). Insert the pin to the hole to prevent the Nylon cord assembly from rotating.
Rotate the Nylon cord assembly counter clockwise to take it out. Insert the slotted screw driver and take out the BODY CAP (139).
Now there appears Reel (137) with NYLON LINE PA66, ORANGE 2.6MX2(138), WASHER 39.5X27.2X0.8 (133), SPRING
(134) and WASHER 39.5X27.2X0.8 (135).
Assembly of Nylon Cord Assembly for ER2600L
Place WASHER 39.5X27.2X0.8 (133), SPRING (134), WASHER 39.5X27.2X0.8 (135), REEL (137) with NYLON LINE PA66,
ORANGE, 2.6MX2 (138) and BODY CAP (139). After placing Body cap, make sure that the REEL (137) is bumping up and
down by pushing red circle part of the Reel (137).
115
PIN
139
140
138
137
135
134
133
Disassembly Procedure
Unscrew 2 CROSSRECESS BOLTS M6X30 (115) and SOCKET HEAD BOLT M5X12 (116).
Using 1R311 (Retaining ring pliers with long bent nails), take out the INNER SNAP RING (120).Wrap the paper around
the bearing case (127) as illustrated below. Using water pump pliers, turn the BEARING CASE (127) counter clockwise. In order
to protect the BEARING CASE from the damage, Please use the paper before sandwiching bearing case. Using arbor press, press
fit the red circle part to take out the shaft.
115
116
1R311
127
134
135
137
133
138
137
139
Assembly Procedure
Press fit the shaft into BALL BEARING 608ZT (122) and then insert the shaft with BALL BEARING 608ZT into BEARING
CASE, WASHER 16X8.3X2.2 (128), SPRING WASHER (129) and SPOOL BASE (130).
Using 1R311(Retaining ring pliers with long bent nails), insert the inner snap ring(120).
Insert the bearing case into pipe then fix with SOCKET HEAD BOLT M5X25(126) and CROSSRECESS BOLT M6X30(115).
130
Vise
122
128
129
130
Water Pump Pliers
128
124
129
130
121
127
123
122
Insert the pin to prevent the NYLON CUTTING HEAD ASS'Y(140) from rotating.
DISASSEMBLY & ASSEMBLY PROCEDURES
(Common in EM2600U, EM2600L and ER2600L)
Precautions in Disassembly & Assembly
Disassembly
1.Handle disassembled parts with care, and clean and keep them in order.
2.Clean off mating surfaces of removed packing components.
Assembly
1.Note assembly order (and assembly direction).
2.Replace packing/gaskets as required.
3.Check operation and sound after assembling key parts.
Fig .II-1
115
126
140
Pin
120
Separating/ConnectingEngine and Tool
1. Separation
Loosen the 2 bolts on holder case in order to remove drive
shaft from holder case(Fig .II-1).
2. Connection
1.Fully insert the drive shaft into the holder case
(Approximately 60 mm;2-3/8",). If the inner shaft resists full
insertion of the drive shaft, insert it again after slightly
rotating the drive shaft or the support washer on the gear case
to match the inner shaft with the hole inside the holder case.
2.After making sure that the drive shafts is installed fully and
correctly, tighten the screws M5 X 18 to secure the drive
shaft.
Connection of throttle wire
1.Connect the throttle wire (Fig .II-2)
2.Squeeze the throttle lever to make sure that the throttle
wire moves smoothly.
3.Connect the switch cords to the two cords from the
engine by inserting one into the other.
4.Wrap the waist pad around the drive shaft so that the
hanger will protrude through the slit in the waist pad and
the throttle wire and the cords will also be wrapped under
the waist pad.(Fig.II-3).
Fig .II-2
Fig .II-3
5.Insert the bullet connectors. (Fig. II- 4). Fig .II-3
Fig .II-4
Disassembly & Assembly of Tool
Disassembly Procedure for EM2600U and EM2600L
1.Remove clamp bolt. Take off inner snap ring.
2.Tap surface A with plastic hammer to remove
gear.
3.Take off inner snap ring.
4.Tap surface B with plastic hammer to remove cutter
shaft.
(Assembly Procedure)
Perform in reverse order of disassembly procedure.
CAUTION:
1. Apply grease as required.
2. After assembly, turn cutter shaft to check operation and sound.
A) Gear head
shield
Gear
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Makita Trimmer Handbücher
Makita
Makita EN420MP Bedienungsanleitung
Makita
Makita UM600D Bedienungsanleitung
Makita
Makita 3709 Bedienungsanleitung
Makita
Makita DUH501 Bedienungsanleitung
Makita
Makita EBH252U Benutzerhandbuch
Makita
Makita DUN500W Bedienungsanleitung
Makita
Makita ER2550LH Benutzerhandbuch
Makita
Makita DUR193 Bedienungsanleitung
Makita
Makita DUH507Z Bedienungsanleitung
Makita
Makita GRU05 Bedienungsanleitung
Makita
Makita um4030 Bedienungsanleitung
Makita
Makita EH7500S Bedienungsanleitung
Makita
Makita DUH521 Bedienungsanleitung
Makita
Makita EBH341U Benutzerhandbuch
Makita
Makita DUR141 Bedienungsanleitung
Makita
Makita DUR365U Bedienungsanleitung
Makita
Makita DUR142L Bedienungsanleitung
Makita
Makita DUN461W Bedienungsanleitung
Makita
Makita EM4351UH Benutzerhandbuch
Makita
Makita 3702B Bedienungsanleitung
