Makita UML2OOD Bedienungsanleitung

Battery Cartridge 7000

120

(4-3/4")

MODEL UMl2OOD

120

(4-314")

MODEL

UMlZOODW

With Fast Charger

Model DC7100 Fast charger

INSTRUCTION MANUAL

input

Charging

time

Voltage

SPEC

CAT

Dimensions Net

weight

output

Model UM1200D

Effective cutting width

No load speed

Dimensions

Net weight

lbsl

361

126

773

I14 114"

30 318")

120

14 314

13,000

Rimin

A.C. only

145

0.7

lHr

)50Hz-60Hz

P:V

314"

3-118"

2-318")

5lbsl

Manufacturer

reserves

the

right

to change

specifications

without

notice.

Note:

Specifications

may

differ

from

country

country.

IMPORTANT

SAFETY INSTRUCTIONS

(For

All Tools)

WARNING:

WHEN USING ELECTRICTOOLS, BASIC SAFE-

TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO

SONAL INJURY, INCLUDING THE FOLLOWING:

REDUCE THE

RISK

OF FIRE, ELECTRIC SHOCK, AND PER-

READ ALL INSTRUCTIONS.

Be aware that this appliance is always in an operating condition, because

does not have to be plugged into an electrical outlet.

Avoid Dangerous Environment

Don't use or leave appliances in damp

or wet locations.

Don't Use

Rain.

Keep Children and Pets Away

All visitors should be kept at a distance

from work area.

Dress Properly

Do notwear looseclothingorjewelry. They can be caught

in moving parts. Use of rubber gloves and substantial footwear is recom-

mended when working outdoors. Do not wear slippers, sandals, etc.

Use Right Appliance

not use appliance for any job except that for

which

is intended.

Avoid Unintentional Starting

Don't carry appliance with finger on switch.

Be sure switch is off when inserting battery cartridge into the appliance.

Don't grasp the exposed cutting blades or cutting edges when picking up

or holding the appliance.

Don't Force Appliance

will do the job better and with less likelihood

of a risk of injury at the rate for which

was designed.

IO.

Don't Overreach

Keep proper footing and balance at all times.

11.

Store Idle Appliances Indoors

When not in use, appliances should be

stored indoors

dry, high or locked-up place

out of reach of children.

12.

Maintain Appliance With Care

Keep cutting edge sharp and clean for

best performance and to reduce the risk of injury. Follow instructions for

lubricating and changing accessories.

IMPORTANT SAFETY INSTRUCTIONS

Length of Cord (Feet)

AWG Size of Cord

SAVE

THESE

INSTRUCTIONS

This

manual

25 50 100 150

18 18 18 16

not operate charger with damaged cord or plug

replace them im-

mediately.

IO.

Donotoperate charger if

has receiveda sharp blow, beendropped, or other-

wise damaged

any way; take

to a qualified serviceman.

11.

Do not disassemble charger or battery cartridge; take

to a qualified

serviceman when service

repair is required. Incorrect reassembly may

result

a risk of electric shock or fire.

12.

To reduce risk of electric shock, unplugcharger from outlet before attempt-

ingany maintenance or cleaning. Turningoff controls will notreduce this risk.

ADDITIONAL SAFETY RULES

FOR CHARGER

BATTERY CARTRIDGE

not charge Battery Cartridge when temperature is BELOW 10°C (5OOF)

not attempt tousea step-up transformer, an enginegenerator or DC power

not allow anything to cover or clog the charger vents.

not short the battery cartridge:

or ABOVE 4OoC (104OF).

receptacle.

not touch the terminals with any conductive material.

(2)

Avoidstoring battery cartridge ina container withother metalobjects such

(3)

not expose battery cartridge to water or rain.

as nails, coins, etc.

A battery short can cause a largecurrentflow, overheating, possible burns

and even a breakdown.

not store the tool and Battery Cartridge in locations where the tempera-

not incinerate the Battery Cartridge even if

is severely damaged or is

ture may reach or exceed 5OoC (122OF).

completely worn out. The battery cartridge can explode in a fire.

ADDITIONAL SAFETY RULES

FOR CORDLESS GRASS

TRIMMER

1. Keep guards in place and

working order.

Keep hands and feet away from cutting area. The blade coasts for several

seconds after the tool has been turned off.

Always use eye protection.

This tool is for cutting grass or weeds only.

not use

for other purposes.

prevent personal injury or damagetothe tool, removerocks, wire and large

Stop the tool immediately

you notice anything abnormal.

you find cracks

sticks from the work area before cutting.

or damage

the blade, replace

immediately.

SAVE THESE INSTRUCTIONS.

ASSEMBLY

CAUTION

Always be sure that the battery cartridge

Remove the wing bolt from the motor

housing. Insert the shaft into the motor

housing, align the hole in the shaft with

the hole in the motor housing. Replace

the wing bolt and tighten

securely.

.Remove the wing bolt from the grip.

Insert the shaft into the grip, align the

hole in the shaft with the hole in the

grip. Replace the wing bolt and tighten

securely.

.Slide the guard ring on the safety guard

into the position shown in the figure and

push the safety guard into the slot in the

motor housing.

removed beforeassembling the trimmer.

Wing

bolt

Fig.

Safety

guard

Fig.

Installing or removing battery cartridge

Always switch off the tool before insertion or removal of the battery cartridge.

.To remove the battery cartridge, pull out

the

set

plate on the bottom of the tool

and grasp both sides of the cartridge

while withdrawing

from the barrel.

.To insert the battery cartridge, align the

tongue on the battery cartridge with the

groove in the housing and slip

into

place. Snap the

set

plate back intoplace.

Be sure to close the

set

plate fully before

usingthe tool.

notuse force when insertingthe battery cartridge.

Ifthe cartridge does notslide ineasily,

notbeing insertedcorrectly.

Charging

.Plug the

fast

charger into your power

source. Insert the battery cartridge

that the plus and minus terminals on the

battery cartridge are on the same sides

their respective markings on the fast

charger. insert cartridge fully into the

port

that

rests on the charger port

floor.

Fig.

CAUTION

.Your new battery cartridge

notcharged. You will need tocharge

before use.

If you try to charge

cartridge from

just-operatedtool, sometimesthe charginglight

will not come on after you insert

cartridge from

just operatedtool.

Let

the cartridge

cool off for

while. Then re-insert

and try tocharge

once more.

If youwish tocharge two battery cartridges, allow

minutes betweenchargings on the

fast charger.

Installing or removing blade

CAUTION

Always be sure that the battery cartridge

removedbefore installingor removingblade.

Insert the blade into the groove in the

blade holder untilthe blade

held by the

two

protrusionson the blade holder.

Fig.

CAUTION

Always be sure that the blade

installed properly beforeoperation.

the

remove the blade, bend both ends of

blade up until

will slip

and over

protrusions.Then pull the blade out.

CAUTION

Replace the used blade before

worn

down too far, or you will have difficulty

in bending the ends up to remove

it.

this happens, insert

new blade between

the used blade and the blade holder, hold

the both blades and pull them out.

Fig.

Switch action

.To prevent the trigger from being acci-

dentally pulled,

lock-off lever

pro-

vided

safety feature.

To start the tool, slide the lock-out lever

in the direction of the arrow and pull the

trigger.

Release

the trigger tostop.

Lock-off

lever

CAUTION

Before insertingthe battery cartridge into

the tool, always check to

see

that the

trigger switch actuates properly and re-

turns to the

"OFF"

position when re-

leased.

Fig.

Operation

.Hold the tool firmly without the blade

making any contact. Then turn the tool

on and gently move the tool back and

forth in the area to be cut, keeping the

blade parallel with the ground and

the

desired cutting height. When cutting

tall

grass or heavy weeds, proceed slowly. If

you

attempt to cut too much

time,

the blade may

get

tangled with weeds,

causing the motor to stop. When this

happens, turn the tool off immediately

and remove the grass or weeds from the

blade.Then resume operation.

Fig.

When cutting grass or weeds adjacent to

walls, curbing, etc., move the tool slowly

and smoothly along the curb with the tip

of the blade contacting the curb very

lightly. This may cause the curb to be

scratchedslightly or may cause premature

blade wear. However,

the

tool itself will

not be adversely affected.

Blade

Ground'

Fig.

CAUTION

Forcingthe tool may shortenthe operating time per battery charge.

If the tool

operatedcontinuously until the battery cartridge has discharged, allow the

tool to rest for

minutes before proceedingwith

fresh battery.

NOTE

You can expect upto

minutes running time on

single charge.

MA1NTENANCE

CAUTION

Always be sure that the tool

switched off and the battery cartridge

removed before

attempting to perform inspection.or maintenance.

Cleaning blade and blade holder

*After operation, clean off the blade and

the blade holder with

soft brush. Failure

to clean off the blade holder may cause

difficulty ininstallingthe blade.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance of

adjustment should be performed by Makita Authorized or Factory Service Centers,

always using Makita replacement parts.

ACCESSORIES

CAUTION

These accessories or attachments are recommended for use with your Makita tool specified in this

manual. The use

any other accessories or attachments might present

risk of injury to persons.

The accessoriesor attachments should be used only inthe proper and intended manner.

Makita Battery cartridge 7000

Part No. 632003-2

Blade

(20per pkg.)

Part No. 792374-0

Fastcharger (Model DC7100)

Battery holster

Holster holds extra battery.

Part No.823033-3C

Fast charger

Model DC7012

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Makita Trimmer Handbücher

Makita

Makita RBC420 Benutzerhandbuch

Makita

Makita DUH483 Bedienungsanleitung

Makita

Makita DUN461W Bedienungsanleitung

Makita

Makita EN5550SH Bedienungsanleitung

Makita

Makita 3709 Bedienungsanleitung

Makita

Makita DUR366L Bedienungsanleitung

Makita

Makita DUR141 Bedienungsanleitung

Makita

Makita UR140D Bedienungsanleitung

Makita

Makita UH004G Bedienungsanleitung

Makita

Makita DUH481 Bedienungsanleitung

Makita

Makita DUR190U Bedienungsanleitung

Makita

Makita DUH481 Bedienungsanleitung

Makita

Makita MT370 Bedienungsanleitung

Makita

Makita EM4351UH Benutzerhandbuch

Makita

Makita UH4570 Bedienungsanleitung

Makita

Makita DUR365U Bedienungsanleitung

Makita

Makita DUR182U Bedienungsanleitung

Makita

Makita BUR142U Bedienungsanleitung

Makita

Makita UR100D Bedienungsanleitung

Makita

Makita DUH481 Bedienungsanleitung

Makita

Makita RT0700C Bedienungsanleitung

Makita

Makita RST210 Bedienungsanleitung

Makita

Makita BBC300LRDE Bedienungsanleitung

Makita

Makita DRT50ZJX2 Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung

Efco

Efco STARK 38 Handbuch

Fieldmann

Fieldmann FZS 1001-A Bedienungsanleitung