Mamiya 645 AFD III Bedienungsanleitung
Mamiya 645 AFD Instruction Manual Companion for
Digital Photography
Mamiya 645 AFD Instruction Manual Companion for
Digital Photography
Congratulations on your purchase of the Mamiya 645AFD. To make the transition from film to digital
easier, we are including this digital companion that explains all of the new indicators you will see on the
LCDs of your Mamiya 645AFD. Please read the owner’s manual before reading this companion. Because
the Mamiya 645AFD was made to communicate with digital camera backs, these indicators will inform you
of the status of the communications between your Mamiya 645AFD and digital camera back. If you do not
have a digital back, these indicators will not appear and you do not have to read any further.
There are three basic modes that your Mamiya 645 AFD goes through when taking a digital image. First is
the Normal or pre-capture mode. The camera is in this mode before the shutter is released. While in this
mode the camera virtually acts as if there were a film magazine attached. Shutter speeds and apertures are
displayed on the internal and external LCD displays.
The second mode is after the shutter release button has been pressed. This is the Capture mode. At this
time the Mamiya 645 AFD will start to act very differently when a digital back is attached. There is a whole
new set of indicators that will be displayed on the LCD displays of the camera.
The After Capture mode is the third and final mode. Again, in this mode there are new indicators that will
appear on the camera’s LCD displays. The following will describe these displays and what they signify.
Please note:
All of the following displays are possible. They will be displayed on the Mamiya 645 AFD’s internal and
external LCDs. Some digital backs will not display some or any of the following information. This will
depend on the digital back manufacturer’s design.
Condition #1
This display will appear before the shutter has been released (Normal
mode). At this point the Mamiya 645AFD will act as if there is a film
magazine attached and will display shutter speed and aperture respec-
tively. This indication will not appear under conditions 4b, 5 and 6.
Condition #2
This will appear under normal shooting conditions after the shutter has
been released (Capture mode). CaP db tells us the digital back is in the
process of capturing an image. It will be displayed until the digital
capture is complete except under conditions 4b, 5 and 6.
Condition #3
After the CaP db display these indicators may appear (After Capture
mode). Db-E indicates a digital back exposure warning. The +1.3
confirms the meter reading is +1.3 stops higher than the set exposure
on the camera. It will appear in the Manual and X exposure modes. If
the exposure setting set on the camera does not agree with the expo-
sure determined by the meter, this will be displayed showing the
difference between the two. When this appears, it will blink for three
seconds. It can be cancelled by pressing any button.
Internal LCD External LCD
Condition #4
After CaP db is displayed these indicators may appear (After Capture
mode). It confirms the digital back is storing an image and that there
are certain number of frames left in the memory of the digital back. This
indicator shows the remaining frames left by displaying Stor 88 (where
88 is a number between 99 and 1). This will be displayed when the
frames-to-go is less that 100. This display will blink for 3 seconds and
can be cancelled by pressing any button. Note: Some digital backs will
only display Stor db in this instance. If the db-E and Stor conditions are
both true, the db-E will be displayed for 3 seconds and then Stor will
be displayed for 3 seconds.
Condition #4b
This indicator may appear before the shutter has been released (Normal
mode). This is warning that the storage capacity of the digital back has
been reached. If the shutter release button is pressed at this time the -
no- db indication will blink for 3 seconds.
Condition #5
When the battery of the digital back has been exhausted this indication
will appear. If the shutter release is pressed the -no- db indication (see
condition #7) will be displayed and blink for 3 seconds.
Internal LCD External LCD
Condition #6
When the digital back or host computer is busy, this indicator will be
displayed. If the shutter release is pressed the -no- db indication (see
condition 7) will be displayed and blink for 3 seconds.
Condition #7
If the digital back is connected to the Mamiya 645AFD and the connec-
tion to the host computer is not installed, this will be displayed when
the shutter release is pressed. This will also appear under the previous
three conditions when the shutter release is pressed.
Internal LCD External LCD
MAMIYA AMERICA CORPORATION
8 Westchester Plaza, Elmsford, NY 10523
Phone: (914) 347-3300 · Fax: (914) 347-3309
E-mail: [email protected]
Andere Handbücher für 645 AFD III
2
Inhaltsverzeichnis
Andere Mamiya Digitalkamera Handbücher
Mamiya
Mamiya 645 AF Bedienungsanleitung
Mamiya
Mamiya ZD Bedienungsanleitung
Mamiya
Mamiya 645DF Bedienungsanleitung
Mamiya
Mamiya 645 Bedienungsanleitung
Mamiya
Mamiya 6 Bedienungsanleitung
Mamiya
Mamiya 645 AFD III Bedienungsanleitung
Mamiya
Mamiya RB67 Pro-S Bedienungsanleitung
Mamiya
Mamiya 645 AFD II Bedienungsanleitung
Mamiya
Mamiya PRO 645 Bedienungsanleitung
Mamiya
Mamiya 7 Bedienungsanleitung
Mamiya
Mamiya M645 Super Bedienungsanleitung
Mamiya
Mamiya ZD Back Bedienungsanleitung
Mamiya
Mamiya ZD Bedienungsanleitung
Mamiya
Mamiya DM System Bedienungsanleitung
Mamiya
Mamiya 645DF Bedienungsanleitung
Mamiya
Mamiya 7 II Bedienungsanleitung
Mamiya
Mamiya C3 Bedienungsanleitung
Mamiya
Mamiya 645 AF Bedienungsanleitung
Mamiya
Mamiya M645 1000S Bedienungsanleitung
Mamiya
Mamiya M645 Super Bedienungsanleitung
