Mantion WIDOOR Bedienungsanleitung
INSTALLATION INSTRUCTIONS
DOOR MOTOR
WIDOOR
VERSION 3-02 EN
2, rue des Métiers
21110 –Genlis
Tel.: (33) 03 80 37 85 71
http://www.mantion-smt.fr
2
GUARANTEE - IMPORTANT SAFETY INSTRUCTIONS.
These instructions must be followed in the interest of personal safety; Keep these
instructions.
This motorization is exclusively designed for opening and closing sliding internal doors. It must not
be used for any purpose other than that specified in these instructions. The manufacturer or
supplier shall not be liable for any damage resulting from improper use thereof. The user alone
shall be solely liable and assume any risks arising from improper use of the product.
This door motor must be installed by persons fully aware of the hazards involved with electric
currents, and having all qualifications to work on domestic installations in accordance with good
practice.
Follow all these instructions because faulty installation can cause injuries.
The assembly steps must be followed, as must the operating instructions, and safety rules must
always be heeded.
Before installing the door motor, check that both the driven part and the supplied motor are in
good mechanical condition; and that the structure has the necessary load-bearing capacity for our
product in its entirety.
The electrical installation must be done according to prevailing national standards. The power
supply must be compatible with our product (voltage and frequency as specified on the product)
Do not connect the device without first checking that the control circuit is disconnected from the
power supply.
Check the installation frequently to detect any signs of wear and tear or damage. Do not use the
device if it needs repairing or adjusting.
Always disconnect the power supply when cleaning or carrying out any maintenance or servicing
tasks on the product.
Never modify or fit any additional parts to the device that may compromise safety without
MANTION SMT's written permission.
The user alone is solely and entirely responsible for any breach of these safety rules, and any
damage resulting therefrom.
The product must be stored indoors in a dry place at a temperature of between 0 °C and +50 °C.
When fitting it, the installation engineer must heed accident prevention instructions and the
standards in force in the country.
Do not immerse the gear motor in water or splash it.
Do not dispose of it in fire or bring it into contact with flame or any heat source.
Do not use household products or chemicals to clean it.
Do not dispose of the packaging in the environment; treat waste according to the standards in
force in the country.
Keep products, devices and documentation out of reach of children.
Do not let children play with the fixed control devices. Keep remote controls out of reach of
children.
This product may be used by children over the age of 8 and by persons with reduced physical,
sensory or mental capabilities, or inexperienced persons, if they are properly supervised, or they have
been given proper instructions on the safe use of the product, and possible risks have been removed.
3
Children must not play with the product. Cleaning and maintenance must not be carried out by
children, without supervision.
The manufacturer or supplier shall not be liable for any damage resulting from any other use of the
product. If replacing the product, only use MANTION SMT or MANTION SMT-approved products.
Terms of the guarantee
MANTION SMT products come with a 5 (five) year guarantee from the date of delivery.
The guarantee is limited, as decided by MANTION SMT, either to replacement or to repair of
products that MANTION SMT recognizes as faulty, with the proviso that:
1. Subject to MANTION SMT's written permission to return the products, the said products are
returned to MANTION SMT forthwith with the details of the fault and a copy of the
installation engineer or dealer's bill stating the date of installation.
2. The products have been stored, installed, maintained and used in accordance with
MANTION SMT's instructions and specifications.
The guarantee is strictly limited to the provisions of this clause, and any other guarantee or
liability, including loss of profits or damage directly or indirectly resulting from the sale or use of the
products, is excluded.
MANTION SMT shall in any event only be liable for the motorization. The guarantee does not
apply in case of overvoltage or short-circuiting resulting for instance from connection errors,
weather conditions such as lightning, etc. The guarantee does not cover normal wear.
4
Summary:
1. Technical characteristics...........................................................................................................5
2. Kit contents................................................................................................................................7
3. Installation diagram ...................................................................................................................7
4. Pre-installation checking............................................................................................................8
5. Motor installation .......................................................................................................................9
5.1. Gear motor establishment............................................................................................................................ 9
5.2. Belt fixing on the door (not included).........................................................................................................10
5.3. Free pulley installation (not included) ........................................................................................................ 10
6. Electrical connection................................................................................................................11
6.1. External accessories connection ................................................................................................................. 12
6.2. Peripherals connections.............................................................................................................................. 13
6.3. Power supply connection (terminal C1)...................................................................................................... 14
7. Protection cover installation.....................................................................................................16
8. Operating modes.....................................................................................................................17
8.1. Switches settings......................................................................................................................................... 17
8.2. Closing modes ............................................................................................................................................. 17
9. Bringing into service................................................................................................................18
10. Parameters settings.............................................................................................................19
10.1. Peering a smartphone............................................................................................................................. 19
10.2. Disabling all smartphones .......................................................................................................................19
10.3. Adjustable parameters via mobile application .......................................................................................19
11. Wireless setup instructions (Radio product only) .................................................................20
11.1. Radio specifications.................................................................................................................................20
11.2. Peering a switch or a remote control (transmitter)................................................................................ 20
11.3. Disabling a switch or a remote control (transmitter) .............................................................................21
11.4. Disabling all transmitters (switches, remote control, etc.)..................................................................... 21
11.5. Other informations .................................................................................................................................21
12. Further information...............................................................................................................22
12.1. LED color code......................................................................................................................................... 22
12.2. Restart after power outage.....................................................................................................................22
12.3. Obstacle detection .................................................................................................................................. 22
13. Diagnostic aid.......................................................................................................................23
5
1. Technical characteristics
This product is used for opening and closing automatically sliding doors (one or two doors). It is
designed for domestic or professional use.
General informations
Reference
K0000256 –Wire control
K0000266 –Radio control
Designation
Sliding door motorization
Technology
Belt transmission
Connectivity
Radio (433,92 MHz) / Bluetooth (BLE4.1)
Size
L= 150 mm, T= 45 mm, H= 205 mm
Maximum weight per door
10 –80 kg or 10 –50 kg for double doors
Max speed
350 mm/s *
Max distance
6 m
Frequency of use
500 cycles per day (maximal recommended)
Guarantee
5 years
* Measure is given for indicative purpose, using a 50kg door.
Electrical
Power Supply
80 –264 VAC
Frequency
47 –63 Hz
Nominal Power
65 W
Current max
1,5 A at 115 VAC / 1 A at 230 VAC
Isolation class
Class II
Protection
Internal fuse 2,5 AT
Recommended power cable
3G0,75 mm² for a maximum length of 20 m
Environment
Protection rating
IP 20
Operating temperature
+5 °C < T < +40 °C
Options
Command
Wired: push button or radar
Radio: transmitter 433 MHz
Command and parameter
setting
Smartphone application (Android or IOS)
Lock output
Allow to plug a locker (24 VDC, 500 mA max.)
Safety input
Allow to plug a safety input
6
Setting Parameters
Max opening speed
50 mm/s –350 mm/s *
Max closing speed
50 mm/s –200 mm/s *
End opening speed
End closing speed
Increase or decrease the speed at the end position
Deceleration at the opening
Adjust the deceleration according to the weight of the
door
Timer before closing the door
0 s –60 s
* Measure is given for indicative purpose, using a 50kg door.
Normative / directive compliance
Equipment safety
EN60335-1, EN60335-2
People security
Obstacle detection
impact force < requirement of the standard EN16005
EMC
EN61000-6-1, EN61000-6-2, EN61000-6-3, EN61000-6-4
ROHS Directive
2002/95/C
7
2. Kit contents
Motorization
Screws and
adhesive band
Electrical
terminal
Protection
cover
3. Installation diagram
Recommended components (not included):
x 4
Fixing bracket
Free pulley
Stoppers x 2
Belt
Track
8
4. Pre-installation checking
Operating reserve: 150 mm in width and 45 mm for thickness.
Do not use locking stoppers.
150 mm min
70 to 77 mm
45 mm min
Porte
9
5. Motor installation
5.1. Gear motor establishment
In the track, slide the nuts fixing the system.
Tighten the two M6 screws.
Note: if the motorization is between walls, put adhesive bands.
Nuts x 2
M6 screws
10
5.2. Belt fixing on the door (not included)
5.3. Free pulley installation (not included)
Inhaltsverzeichnis
