Mantis 7945 Bedienungsanleitung

P/N 430100, Rev A

IMPORTANT NOTE:

Read the Safety Rules &

Warnings before you use

your Mantis tiller

QUICK ASSEMBLY SHEET

Model 7945

Tiller/Cultivator

QUICK ASSEMBLY SHEET

Model: 7945 Tools Needed: Two 7/16” wrenches

Tighten Hardware Tine Installation

Honda engine shown. Engine type depends on the model of the tiller.

Attach the Upper Throttle

Handle onto the Right Lower

Handle. Fasten together using

the Knob T12 and Carriage Bolt

T42. Place an Acorn Nut T13

on the end of the Carriage Bolt.

Repeat this process for the Left

Upper Handle.

Upper Handles

Step 3

Slide the tines onto the

axle shafts. The “D-

shaped” hole goes on the

outside. Secure each tine

to the axle by inserting a

Tine Retaining Pin T41.

Step 7

Tighten all Lock Nuts, Cap

Screws, and Bolts firmly and

securely using two 7/16”

wrenches.

Note: Do not over-tighten the

Acorn Nuts.

Step 6

Throttle Clip

Use the Clip T9 to secure

the Throttle Cable and

wire in place on the Right

Lower Handle.

Step 4

Lower Handles

Slide two (2) T11 Bolts through the holes

of one Handle Clamp and then through

the holes of the Left Lower Handle.

Position the bolts so that one bolt is in

front and one bolt is behind the

recessed channels of the transmission

housing. Slide the Right Lower Handle

and the second Handle Clamp onto the

bolts. Finger tighten the Nuts T14.

Step 1

Slide the Carrying Handle

over both Lower Handles.

Slide it down towards the

engine. It will rest about

four to six inches above the

engine.

Step 2

Carry Handle

Hardware

T15

T42

T13

T12

T14

T41

T11

T15 - ¼-20 x 1.125” Cap Screws

T42 - ¼-20 x 2.25” Carriage Bolts

T13 - Acorn Nut

T41 - Tine Retaining Pins

T11 - ¼-20 x 3” Hex Bolt

T14- ¼-20 two-way Lock Nut

T9- Throttle clip

T7- Clamp

T12- Knob

Line up the Handle Brace with

the holes on the Upper Handles.

Insert Cap Screws T15 through

the holes in the Handle Brace and

through the holes on the Upper

Handles. Secure with a Lock Nut

T14.

Handle Brace

Step 5

Andere Handbücher für 7945

Inhaltsverzeichnis

Andere Mantis Pinne Handbücher

Mantis

Mantis Tiller/Cultivator Bedienungsanleitung

Mantis

Mantis 7234 Programmierhandbuch

Mantis

Mantis Tiller/Cultivator Bedienungsanleitung

Mantis

Mantis DELUXE 7264 Bedienungsanleitung

Mantis

Mantis Tiller/Cultivator Bedienungsanleitung

Mantis

Mantis 7567 Programmierhandbuch

Mantis

Mantis 3450-02 Bedienungsanleitung

Mantis

Mantis 7263 Bedienungsanleitung

Mantis

Mantis Mantis-20 Benutzerhandbuch

Mantis

Mantis Tiller Bedienungsanleitung

Mantis

Mantis 7940 Produkthandbuch

Mantis

Mantis Tiller/Cultivator Bedienungsanleitung

Mantis

Mantis 8222 Bedienungsanleitung

Mantis

Mantis SV-5C/2 Bedienungsanleitung

Mantis

Mantis 7234 Bedienungsanleitung

Mantis

Mantis 7920 Bedienungsanleitung

Mantis

Mantis 7222 Bedienungsanleitung

Mantis

Mantis 7234 DELUXE Bedienungsanleitung

Mantis

Mantis ElectricTiller Bedienungsanleitung

Mantis

Mantis 7566 Programmierhandbuch

Mantis

Mantis ElectricTiller Bedienungsanleitung

Mantis

Mantis Tiller/Cultivator Bedienungsanleitung

Mantis

Mantis Tiller/Cultivator Bedienungsanleitung

Mantis

Mantis SV-5C/2 Bedienungsanleitung

Beliebte Pinne Handbücher anderer Marken

MTD

MTD 410R Bedienungsanleitung

Craftsman

Craftsman 247.29931 Bedienungsanleitung

MTD

MTD FRT Series Bedienungsanleitung

Craftsman

Craftsman 917.298353 Bedienungsanleitung

Troy-Bilt

Troy-Bilt Colt FT Bedienungsanleitung

Ryobi

Ryobi 510r Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

YAT

YAT YT5601-01 Wartungshandbuch

Craftsman

Craftsman 917.296010 Bedienungsanleitung

Troy-Bilt

Troy-Bilt OEM-290-260 Bedienungsanleitung

Scheppach

Scheppach MTP560 Montageanleitung

GARDEN WAY

GARDEN WAY 12194 Bedienungsanleitung

Classen

Classen STAND-AER SA-25 Montage- und Wartungsanleitung

Craftsman

Craftsman 850 Series Bedienungsanleitung

DR PILOT 2 Kurzanleitung

Altrad

Altrad ATIKA BH 1400 N Leitfaden

WIL-RICH

WIL-RICH 2500 Bedienungsanleitung

Viking

Viking HB 685 Bedienungsanleitung