Marey ECO110 Bedienungsanleitung
ELECTRIC HEATER
INSTRUCTIONS MANUAL
Keep this manual with you after your unit has been installed,
you may need it for further technical information.
ECO110 MODEL
02 03
INSTALLATION GUIDE
INSTALLATION
RESTRICTIONS
ENERGY SAVING TIPS
OTHER POWER REQUIREMENTS
HOW TO USE
TEMPERATURE CONTROL
QUICK INSTALLATION GUIDE
STEPS TO RESET THE HEATER
CUSTOMER SERVICE
OTHER PRODUCTS
04
04
06
06
07
08
08
09
11
12
13
Congratulations!
You've just purchased a new Marey ECO110 tankless water heater and
will soon begin to enjoy the benefits of “going tankless.”
Takethetimetothoroughlyreadandunderstandthissafetyandinstallation
manualinitsentiretybeforeyouattempttoinstallyournewECO110tankless
water heater, as it contains important safety tips andinstructions.
Pleasecarefullyreadallinstructionsandwarnings. Ifyouneedassistance or
have any questions please contact us at:
Please keep this manual for future reference.
1-512-332-2229
IMPORTANT!
Workingaroundelectricityrequiresproperskillsandknowledge–andshouldnotbe
performedbysomeonewhoisnotfamiliarortrainedinthistrade.Therefore,weHIGHLY
recommend that you solicit the services of a licensed and qualified
“Electrician/Plumber”familiarwithtanklesswaterheaterinstallation.
All electrical work and setting the unit to the wall should be completed before any
electricalwiringconnections.
IMPROPER INSTALLATION CAN CAUSE INJURY OR EVEN DEATH.
I) WALLFIXING
- Turn off the power or running water.
-Mark thepositionofthepointsofthe3screws.Notethatwerecommendleaving6
inchesclearance(free)aroundtheheater,therebyfacilitatingtheproperinstallation
and maintenance.
- The heater must beinstalled vertically and secured with 3 screws using the“drill
hole template” included with this heater.
-Set the heater at the pointswherethescrewsshouldgo,usetheadaptersand
screws provided.(viewphotos)
II) PLUMBING
- Uses tainless steel flexible hose or copper tubing from ½" to enter and leave
the water heater.(Right side water inlet, hot water outlet, left.) When you have
water pipes reduce the manother size to ½".
- Do not use PVC, CPVC or plastic supply lines to connect the unit. A pipe 16"of
copper or stainless steel must be connected to the input and output of the
heater.
- Connect the isolation valve at the entry inlet pipe of the heater and make sure
you install a rubber washer. Do not apply excessive force to tighten connectors.
Be sure to clean the pipes before connecting the heater to the main line, clean
all the impurities of the pipe allowing water to flow for a few minutes, check for
leaks.
Any residue or dirt in the pipes may cause internal damage to the unit. We
recommend installing a sediment filter before the entry of water to the heater.
Hard water or water with high levels of minerals and alkali can cause damage to
this unit. When this is the case, we recommend the use of a (non-salt) water
softening system.
III) ELECTRICITY
- Install a fuse box or switch (“breaker") for exclusive use of the heater. Based
on the power of the model obtained using the cable for your unit according to
the power and model purchased. Find a detailed guide to the power and cable
type used in the table below. Connect the ground, as indicated in the Electrical
Code.
Find a detailed guide to the power and cable type used in the table below.
Connect the ground, as indicated in the Electrical Code.
Once installed the heater, let the water flow through the unit before turning on
electricity.Whenallconnectionsaresatisfactorilypreparedinstalltheheatercover.
With the insulated container off and flow modifier (optional) fully open, the faucet
must be opened fully to get maximum water flow at the exit. This is necessary to
ensure that the water tank is full before turning your energy is an essential step to
protecttheresistance.
Remember:Runthewaterbeforeturningonelectricity.
NOTE:Theelectricalsupplyisnotturnedonuntilallthepipesandtheinstallationis
complete.
These heaters are of the closed type (closed system with no ventilation pressure)
suitable for fitting to the normal input of cold water with a maximum of 150 PSI (10
bar).Theymustbefittedwithapressurevalveadjacenttotheentrance.
Theheater shouldbeinstalledascloseaspossibletothepointofuse,becausethe
distance to be run the hot water temperature affect. If a shower is used for the
heatershouldbeinstalledoutsidetheshowerstall/area.
When installed in a location that could freeze the heater must be isolated and
drained.
MODEL
MAXIMUM AMPERAGE
CABLE
ECO110
44 A
8 AWG
04 05
-DONOTexposetheunittofreezingtemperatures.Donotuseaninputwater
temperatureover90degreesFor32.2degreesCelsius.
-DONOTrestricttheflowofwaterenteringtheunit.
- DO NOT use the unit if water ceases to flow during use. If the outer case or cover
isloose,yourheaterwillnotworkcorrectly.Animproperlysecuredcovercancause
injuryorelectricshock.
-Thisunitisdesignedforindooruseonly.
NEVEROPERATETHISHEATERWITHOUTTHECOVER!
WARNING!
Whenyouturntheunitcangetextremelyhotwater.Takepropersafetyprecautions
toavoidbeinghurtorbeburnedbywater.
- Ensure that all electrical connections are adequately protected to prevent shock,
overheatinganddamage.
- The fuse does not give personal protection against electric shock. Improving
electrical safety: A single ground fault breaker (GFCI), 30-50 Amp (depending on
configuration and requirements) or a residual current device (RCD) must be
installedonthiscircuit.
-Thisunitrequiresasinglecircuit.Otherelectricalequipmentsuchasfans,pumps,
etc.mustbeonseparatecircuits.
-Turnoffthepowerswitchmanuallyorwhenunusedforextendedperiodsoftime.
-Theunitmustbecertifiedbyanelectricianfromthetimetheyinstalledforan
additionalyear.
NOTE:Improperuseorinstallationwillvoidthewarranty.
-Whenpossible,installtheheaterinthemostcentrallocations,nearesttothepoint
ofuse(wherehotwaterisneeded,e.g.,shower,faucets,etc.)
-Adjustheatertemperaturesettings(locatedonthefrontpaneloftheheater)tothe
desiredoutputtemperatureyoudesire.Loweringthepowersettingwillsave
energy,butwillhavealoweroutputwatertemperature.
- We recommend that you install the unit under the sink in main bathrooms or
utility areas. This will allow for lower amperage usage and a reduced heat loss
from longer pipe runs.
- For additional savings, reduce the water flow valve at the inlet of the heater so
the temperature increases.
WARNING! THIS APPLIANCE MUST BE PROPERLY GROUNDED!
1.Theheatershouldonlybeconnectedtoasupply200/240VAC.
2.TheuseofaplugandoutletisNOTRECOMMENDEDforthisunit.
3.Theheatermustbeconnectedtoitsownindependentelectricalcircuit.Itmustbe
connectedtoamaincircuit,SPUR,ORPLUGOUTlightingcircuits.
4. Make sure that your panel The service has a rate of 30/60 ampere main switch
(the intensity depends on the configuration of the temperature used) If necessary,
contact your energy provider for general use or a licensed electrician to check the
servicerequired.
5. The switch must be accessible and clearly identifiable, but out of reach of a
person with a fixed shower. Except for the cable that has a cable of a key switch,
and must be placed so that it is not possible to touch the switch body standing in a
bathorshower.
6. The unit circuit should be separated from other circuits, at least twice the
diameterofthecableduct.
7. It is essential that the conditions of each site are evaluated by a qualified
electriciantodeterminethecorrectcablesizeandpermissiblecircuitlength.
06 07
MODEL
RECOMMENDED
SWITCH
MAXIMUM
AMPERAGE
@240V
POWER
MINIMUM
PRESSURE
TO ACTIVATE
TEMPERATURE
INCREMENT
MAXIMUM
PRESSURE
TO
ACTIVATE
ECO110
50 A
44 A
11 Kw
8 PSI
45 ºF
150 PSI
IMPORTANT!
The size of the switch and wire gauge must meet all local, state, provincial and
national electrical codes in your area - these are just guidelines that apply to most
installations. Some codes require the use of electrical substations for the
installation panel, especially when heater is not mounted within line of sight of the
main electrical panel. Wiring must be sized to maintain a voltage drop of less than
3%underload.
Therearerealdangersinvolvedinimproperinstallationofanyelectricalappliance.
Improper installation will void the warranty of your unit. Failure to follow proper
installationproceduresthereisariskofinjuryordeath.
Local codes "Most counties, cities and states have specific codes governing the
installation of electrical equipment. You need to know the code and permit
requirementsinyourcommunitybeforeinstallingyourtanklesswaterheater.
- Open the hot water tap and the tankless hot water heater will activate, thus
producing hot water. Mix hot with cold water to achieve the desired output
temperature.
- The speed of water passing through the heater unit, which determines the water
temperature in a given environment (for example, slowing the flow of water will
increasethetemperature.Afasterflowwillresultinaloweroutputtemperature.)
- In cooler regions or cooler seasons of the incoming water temperature will cause
a variation in the output temperature. The temperature settings allow for
compensationofseasonalchanges.
1.Usea#8AWGwireforelectricalconnection.
2.CAUTION:Verifythatthecablesaretight.
3.Usetheillustratedcardboardtofacilitatethecentralizationoftheheaterandthen
havetoscuttlethepointsinordertosupportthescrews.
4. Place expansions and screws, remove the card and enter the furnace or central
bodyonthewallusingscrews.Afterhavingplacedthemainbodycheckthisnut.
5.Verifythatthecentralheater.
6.Placebothandsoftheinletandoutletpipes,
IMPORTANT: Use black boards as shown in the illustration to avoid spillage
ofwater.
7.Presswelltosealtheboardcompletelyblack.
8. Use a flexible stainless steel or cooper, this would facilitate the installation and
makeitlighterandsimpler.
9. Open tha water inlet valve of the heater. check for spill any team at both
entrances.Ifthereisanytypeofstroke,pleasecorrectit.
10.Willtherebeanyclosefaucethotwaterside.
11.Placethefrontcoveroftheheater.
12.Makesurethetwoscrewsatthebottomofthebox.
13.Placetheheaterbuttononthetop.
14.Connecttheplugonthereceptacle.
15.At the conclusion of all the steps correctly, you’re ready to enjoy the benefits of
theheater.
For illustrations, see the photos on the next page.
09
08
1.Unplugthepowercordandelectricalcircuitoftheequipment.
2.Unscrewthetwoscrewsthatareatthebottomofthedeck.
3.Removethetemperaturecontrollerbutton.
4.Removethecovercarefully.
5.Openthehotwaterpenandletthewaterrunabout10seconds.
6. Tighten the two buttons are indicated in the illustration (see Figure 6) and press
eachoneuntilitclicks.
10 11
12 13
1-512-332-2229
customerservice@marey.com
GAS PORTABLE
AQUAMATIC POWER GAS
SANTON
ECO110 POWER PAK
Delbrey Street, 211
San Juan, Puerto Rico
00912
Tel. 1-512-332-2229
www.marey.com
Please visit our website to get to know more about other Marey products.
AtMarey,weprideourselvesontheexcellenceofourcustomerservice and support
team.
Pleasefeelfreetocontactusifyouhaveanyquestionsaboutourproducts, warranty
service, or if you need assistance installing a unit. We also strive for continuous
improvement,sowewelcome your comments, feedback and suggestions.
Andere Handbücher für ECO110
4
Inhaltsverzeichnis
Andere Marey Elektrische Heizung Handbücher
