Marmitek VideoControl3 Bedienungsanleitung

VIDEOCONTROL3

20166 / 20061116 • VIDEOCONTROL 3™

USER MANUAL 3

GEBRAUCHSANLEITUNG 11

GUIDE UTILISATEUR 19

MODO DE EMPLEO 27

MANUALE D’ISTRUZIONI 34

GEBRUIKSAANWIJZING 41

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 1

2© MARMITEK

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 2

Safety warnings

• To prevent short circuits, this product should only be used inside and only in dry

spaces. Do not expose the components to rain or moisture. Do not use the

product close to a bath, swimming pool etc.

• Do not expose the components of your systems to extremely high temperatures

or bright light sources.

• Do not open the product: the device contains live parts. The product should only

be repaired or serviced by a qualified repairman

• In case of improper usage or if you have opened, altered and repaired the product

yourself, all guarantees expire. Marmitek does not accept responsibility in the case

of improper usage of the product or when the product is used for purposes other

than specified. Marmitek does not accept responsibility for additional damage

other than covered by the legal product responsibility.

• Adapters: only connect the adapter to the mains after checking whether the

mains voltage is the same as the values on the identification tags.

Never connect an adapter or power cord when it is damaged. In that case,

contact your supplier.

• This product is not a toy. Keep out of reach of children.

Introduction

Congratulations on buying the Marmitek VideoControl3. With the infra-red extender

VideoControl3 you can transmit infra-red signals via the existing COAX network in your

home and control all equipment connected from another room. Example: you have a

satellite receiver in the living room and a second TV in the bedroom, where you would

like to watch the satellite programs. You would like to control the satellite receiver with

3VIDEOCONTROL3TM

ENGLISH

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 3

the remote control, but do not want to go to the living room. The infra-red extender

VideoControl3 transmits the infra-red signals to the equipment via the COAX cable net-

work.

Set content

• 1 VideoControl3 infra-red receiver with 1 IR LED (IR receiver)

• 1 VideoControl3 infra-red transmitter with 3 IR LEDs (IR emitter)

• 2 power adapters

• Coax extension plugs (IEC-F) male and female

• This user manual

How does it work?

The VideoControl3 transmits the signal from your own remote control back to the

other room via the existing antenna cable. The VideoControl3 consists of an infra-red

receiver and an infra-red transmitter. The receiver is connected to the antenna connec-

tion of a TV (e.g. in the bedroom).

The transmitter is connected to the antenna connection of e.g. the satellite receiver.

You can control up to three different devices (e.g. a satellite receiver, a VCR and a

decoder) using the three infra-red LEDS. If desired, you can place multiple infra-red

receivers in different rooms, to control your video equipment from each TV in your

house.

NOTE: The Marmitek VideoControl3 signal is carried via all antenna boxers, splitters

and antenna amplifiers suitable for a return channel.

4© MARMITEK

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 4

5VIDEOCONTROL3TM

ENGLISH

Installing the receiver

• Connect the ‘IN’ side of the VideoControl3 receiver, (with the character Ron the device,

with the IR LED) to the COAX cable near the TV in the room you want to use

the remote control from (e.g. the bedroom).

• Plug the ‘TO TV’ plug of the receiver into the antenna IN of the TV.

• Use the coax extension plug included if necessary.

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 5

6© MARMITEK

• Position the IR LED within range of the remote control, e.g. on the top of the TV.

• Plug the power adapter into the wall socket.

Tip 1

There are two types of antenna plugs in Europe: the IEC plug and the F plug. This last

one causes the least loss of signal and is used in superior installations. Your Marmitek

VideoControl3 also uses an F plug. With the adapters included you can also connect

IEC plugs.

Installation of the transmitter

• Connect the ‘IN’ side of the VideoControl3 transmitter (with the character Ton the

device and with the IR LEDs) to the COAX cable near the satellite receiver or video

recorder in the room the equipment you want to control is situated.

• Connect the ‘TO TV’ plug to the antenna IN of the TV or satellite receiver.

• Use the coax extension plug included if necessary.

• Stick the LEDs on the IR windows of the equipment. This should be done very

carefully and precisely. Test whether the LEDs are in the right

place first (with another person holding them) before you stick them down.

• Plug the power adapter into the wall socket.

ATTENTION: if you connect less than 3 devices, do not remove the other LEDs from

the cable.

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 6

You have now successfully installed the VideoControl3. The red LED on the receiver and

transmitter will light up as soon as you transmit a command with your remote control.

Tip 2

The receiver has a adjustment screw which you use to set the sensitivity of the recep-

tion. If the red LED lights up when it is not being activated via the remote control, the

sensitivity is too high. If the LED does not light up when you are using the remote con-

trol, it is set too low. Use a Phillips screw driver to change the setting.

Tip 3

If you want to control your equipment from multiple rooms, you can purchase extra

receivers (Art. No. 9709 (E), Art. No. 9715 (UK).

7VIDEOCONTROL3TM

ENGLISH

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 7

Frequently asked questions

I have no picture and no sound.

Check whether all the cables are connected properly.

The infra-red doesn’t work.

a. Check whether the infra-red LED is placed on the sensor correctly.

b. Check whether all the cables are connected properly.

c. Check whether the LEDs on the transmitter and receiver flash up if the IR signal is

activated. You can alter the sensitivity of the receiver by setting the adjustment screw,

see tip 2.

d. The infra-red return channel only works if you are using amplifiers, splitters and

antenna boxes that support return channels. This is usually indicated by the term

‘5-30MHz’ or ‘5-68MHz’. Consult your cable store for more information.

e. Make sure the transmitter cannot control the receiver. The LEDs on the transmit-

ters have to be out of view of the LED on the receiver (acoustic feedback).

f. Make sure that, if you use multiple receivers, these do not all receive an IR signal

at the same time.

g. Prevent interference from other IR sources, such as sunlight, energy lamp

and/or plasma screen.

8© MARMITEK

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 8

Technical data

VideoControl3 infra-red transmitter:

Power adapter: 230VAC/50Hz, 12 VDC/100 mA

RF modulation: 10.52 MHz +/- 250 KHz

Sensitivity: <45 dBuV

VHF/UHF damping: 47 MHz - 230 MHz 2 dB (Max.)

470 MHz - 860 MHz 4 dB (Max.)

Dimensions: 49 x 67 x 26 mm (excl. connection plugs)

VideoControl3 infra-red receiver

Power adapter: 230VAC/50Hz, 12 VDC/100 mA

IR receiver: 37 - 45 KHz

Opening angle: +/- 45 degrees

Reception area: Min. 5 m

RF modulation: 10.52 MHz +/- 250 KHz 110 dBuV (Min.)

VHF/UHF damping: 47 MHz - 230 MHz 2 dB (Max.)

470 MHz - 860 MHz 4 dB (Max.)

Dimensions: 49 x 67 x 26 mm (excl. connection plugs)

9VIDEOCONTROL3TM

ENGLISH

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 9

10 © MARMITEK

Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its pack-

aging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be

disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other

electric and electronic equipment via designated collection facilities appointed by the government or local

authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment

and human health. For more detailed information about the disposal of your old equipment, please contact your

local authorities, waste disposal service, or the shop where you purchased the product.

VideoControl3_manual_20125_20060704.qxd 11-12-2006 15:32 Pagina 10

Andere Handbücher für VideoControl3

Inhaltsverzeichnis

Sprachen:

Andere Marmitek Extender Handbücher

Marmitek

Marmitek Invisible Control 6 Bedienungsanleitung

Marmitek

Marmitek GIGAVIDEO 570 Bedienungsanleitung

Marmitek

Marmitek Powermid XS Bedienungsanleitung

Marmitek

Marmitek Invisible Control 6 XTRA Bedienungsanleitung

Marmitek

Marmitek MegaView61 Bedienungsanleitung

Marmitek

Marmitek MegaView 251 Pro Bedienungsanleitung

Marmitek

Marmitek IR Control 10 XTRA Bedienungsanleitung

Marmitek

Marmitek Megaview60 Bedienungsanleitung

Marmitek

Marmitek Powermid XS Bedienungsanleitung

Marmitek

Marmitek GIGAVIEW 820 Bedienungsanleitung

Marmitek

Marmitek GigaVideo 580 Gebrauchsanweisung

Marmitek

Marmitek IR Eye Bedienungsanleitung

Marmitek

Marmitek MegaView 121 Bedienungsanleitung

Marmitek

Marmitek MegaView 76 Bedienungsanleitung

Marmitek

Marmitek Megaview 80 Bedienungsanleitung

Marmitek

Marmitek MegaView 91 Bedienungsanleitung

Marmitek

Marmitek Powermid XL PM10E Bedienungsanleitung

Marmitek

Marmitek Megaview 80 Bedienungsanleitung

Marmitek

Marmitek VideoControl3 Gebrauchsanweisung

Marmitek

Marmitek IR CONTROL 8 Bedienungsanleitung

Marmitek

Marmitek MegaView 63 Bedienungsanleitung

Marmitek

Marmitek IR Control 11 XTRA Bedienungsanleitung

Marmitek

Marmitek GIGAVIEW 745 Bedienungsanleitung

Marmitek

Marmitek GigaView 911 UHD Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung