Marshall Electronics NCB-2010 Bedienungsanleitung

Marshall Electronic

s, Inc.

1910 East Maple Ave.

El Segundo, CA 90245

Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688

www.LCDRacks.com

•

[email protected]

2010

Marshall Electronics

NCB-2010

Network Control Box for IMD Monitors

Operating Instructions

This Page Intentionally left blank

Specifications (continued)

Dimensions

Warranty

Marshall Electronics warranties to the first consumer that this NCB-2010 Network Control Box will, under normal use, be

free from defects in workmanship and materials, when received in its original container, for a period of one year from the

purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the

warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to

honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not

apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or modifications in design or

construction void this warranty. It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the

periphery of the display active viewing area. Marshall Electronics reserves the option to refuse service for display pixel

failure if deemed unobtrusive to effective use of the monitor by our technicians. No sales personnel of the seller or any

other person is authorized to make any warranties other than those described above, or to extend the duration of any

warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve

products and product features, specifications may change without notice.

Specifications

■CONTROL INPUT

Connector

1 x RJ12 (Modular 6P6C)

Physical Layer

RS-485 / 422

Data Protocols

Image Video:

Start Bits 1

Data Bits 7

Parity Even

Stop Bits 1

Baud Rate 38400

TSL v3.1/v4.0 Protocol:

Start Bits 1

Data Bits 8

Parity Even

Stop Bits 1

Baud Rate 38400

Pinout

■MONITOR OUTPUTS

Connectors

4 x RJ12 (Modular 6P6C)

Physical Layer

RS-422 / 485

Data Protocol

MEI

Start Bits 1

Data Bits 8

Parity None

Stop Bits 1

Baud Rate 57600

Pinout

■NETWORK CONNECTION

Connector

1 x RJ45 (Modular 8P8C)

Physical Layer

10BASE-T or 100BASE-T Ethernet

Data Protocol

TCP/IP

■ELECTRICAL

Power Consumption 3.0A @ 12VDC (36 W)

Voltage Requirement 12 VDC

V-PS12-5V-1 Power Supply:

Input 100V-240V, 1.5A, 50-60Hz

Output 12VDC, 5A, 60W Max

■MECHANICAL

Dimensions (w x h x d): See Dimensions Specifications

Rack Height: 1RU

Weight: 5 lbs

Operating Temperature 32°F to 104°F (0°C to 40 °C)

Storage Temperature -4°F to120°F (-20°C to 50°C)

RoHs Do not dispose. Return to

Manufacturer or Authorized

Recycle Facility.

Pin No. Signal

1 N/C

2 Ground

3 Rx+

4 Rx-

5 Ground

6 N/C

Pin No. Signal

1 Rx-

2 Ground

3 Tx+

4 Tx-

5 Ground

6 Rx+

This Page Intentionally left blank

Contents

Product Overview.........................................................................................................................................................................................................................................5

Features ......................................................................................................................................................................................................................................................5

Installation and Power-On ............................................................................................................................................................................................................................6

Unpacking....................................................................................................................................................................................................................6

Rack Installation...........................................................................................................................................................................................................6

Power-On Procedure....................................................................................................................................................................................................6

Front and Rear Panel Features ......................................................................................................................................................................................................................7

Power LED and Rocker Switch ....................................................................................................................................................................................7

RX / TX / READY LED .................................................................................................................................................................................................7

RS-485/422 Ports.........................................................................................................................................................................................................7

RS-485 / 422 Port 5 .....................................................................................................................................................................................................7

Host Port...................................................................................................................................................................................................................... 7

Ethernet.......................................................................................................................................................................................................................7

Console........................................................................................................................................................................................................................7

Power Input..................................................................................................................................................................................................................7

Connecting to the NCB-2010....................................................................................................................................................................................................................8

Overview......................................................................................................................................................................................................................8

Connecting the NCB-2010 to a Single Computer..........................................................................................................................................................8

Changing the IP Address of the NCB-2010 ................................................................................................................................................................................................11

Procedure..................................................................................................................................................................................................................11

Connectingthe NCB-2010 to an Local Area Network.................................................................................................................................................13

System Configuration .................................................................................................................................................................................................................................14

Basic Remote Control of IMD Monitors.......................................................................................................................................................................14

Wiring Diagram.....................................................................................................................................................................................................14

Monitor Configuration............................................................................................................................................................................................14

Remote Control with Image Video Pass-Through.......................................................................................................................................................15

Remote Control with TSL Pass-Through....................................................................................................................................................................16

Web Interface..............................................................................................................................................................................................................................................17

Web Interface Menu..............................................................................................................................................................................................17

Target Monitor ......................................................................................................................................................................................................17

Protocol Pass-Through Status ..............................................................................................................................................................................18

Display.......................................................................................................................................................................................................................18

Key & Image Enhancement ..................................................................................................................................................................................18

Window Settings...................................................................................................................................................................................................19

Debug Mode......................................................................................................................................................................................................... 19

Waveform Mode ...................................................................................................................................................................................................20

OSD...........................................................................................................................................................................................................................20

OSD Settings........................................................................................................................................................................................................21

IMD Settings......................................................................................................................................................................................................... 21

Tally Settings........................................................................................................................................................................................................ 22

Tools..........................................................................................................................................................................................................................22

Keypad.................................................................................................................................................................................................................22

Ping......................................................................................................................................................................................................................23

Presets.................................................................................................................................................................................................................23

System Logs.........................................................................................................................................................................................................24

Status.........................................................................................................................................................................................................................24

Network Control Box Info......................................................................................................................................................................................24

Device Info............................................................................................................................................................................................................25

Network................................................................................................................................................................................................................26

Help...........................................................................................................................................................................................................................27

Contact Information...............................................................................................................................................................................................27

Table ofWeb Interface Commands............................................................................................................................................................................28

Specifications..............................................................................................................................................................................................................................................30

Warranty.....................................................................................................................................................................................................................................................31

CCMonitor Off, On

OSD IMDState Off, On

Set IMD Intensity 0-100

Send IMD Alignment Left, Center, Right

IMD Send IMD Color Red, Green,

Yellow/Amber

Send IMD String 1-16 characters

Send IMD Name 1-16 characters

Get IMD Name

Show IMD, Show IMD

Name, Show IMD Address

Tally01 [Left] Off, Red, Green,

Yellow/Amber

Tally Tally01 [Text] Off, Red, Green,

Yellow/Amber

Tally01 [Right] Off, Red, Green,

Yellow/Amber

Menu, Select, ↑, ↓, F1, F2,

Power

Keypad Color, Brightness, Contrast +, - , Default

Channel 1 / SDI 1,

Channel 2 / SDI 2,

Channel 3, Channel 4,

Quad / Layout, DVI

Tools Ping Healthy, Warning,

Critical

Presets Load

User1, User2,

User3, User4,

User5, User6,

Factory

Save User1, User2,

User3, User4,

User5, User6

Log

Web version This will change

with updated

firmware releases

System Firmware version This will change with

updated firmware

releases

Hardware version NCB01-2003-B1

Change Current ID Name

Get Version X Software, Keypad,

FPGA1, FPGA2

Get Software Version

Get Protocol Version

Status Device Get Keypad Version

Get Model Number

Protocol Standby, System

Reset

Set Power State Off, On

MAC Address

IP Address

Network Broadcast Address

Netmask

Gateway

Table of Web Interface Commands

Brightness Get, set

Contrast Get, set

Color Get, set

ColorTemp 55k, 65k, 93k,

Linear, User1,

User2

Image Red Offset Get, set

Red Gain Get, set

Blue Offset Get, set

Blue Gain Get, set

Green Offset Get, set

Green Gain Get, set

Analog Phase Get, set

Display 4:3, Scaled 4:3, 16:9,

Centered 16:9

Set Window Layout Single, Quad,

HPOP3, VPOP3

Set Source SDI, DVI

Window 1, Window

2, Window 3,

Window 4,

Set Window Source Channel 1, Channel

2, Channel 3,

Channel 4

Window Set Framelock

Set Marker

Off, 95%, 93%,

90%, 88%, 80%,

1.85:1, 2.35:1, 4:3,

14:9, 13:9

Set Center Off, On

Set Background Transparent, 50%

Gray, Black

Set Curtain Color White, Black, Blue,

Red, Green

Reset Test Mode

SetBlueOnly Off, On

Debug Monochrome Off, On

Set Waveform Mode

YUV Overlay, YUV

Parade, RGB

Overlay, RGB

Parade

Set Waveform Scale Off, Millivolts, %IRE,

Auto

Waveform Color Off, On

Waveform Limits Off, On

Min / Max 0000-1023

Line Mode Off, On

Set Line Number 0000-0000

Set Vectorscope

Targets Off, 75%, 100%

Set Overlay osition Off, Bottom, Top

Waveform

Set Overlay

Transparency 000-100

Config (Baud Rate) 38400, 57600,

115200

Set Protocol Image Video, TSL

Pass-Through On, Off

Read Protocol Type,

Protocol Status

StatusDisplay Off, On

Timecode Off, LTC, VITC

Main AudioMonitor Off, On

Product Overview

The NCB-2010 Network Control box is a comprehensive remote control solution for Marshall’s IMD (In-Monitor Display)

line of monitors. The NCB-2010 offers complete control of each monitor's menu settings and adjustments such as

contrast, color, curtain color, aspect ratio, and more. The NCB-2010 can control up to 255 monitors individually by ID#, or

up to 512 monitors simultaneously on a global scale. The NCB-2010 also enables the use of third party UMD controllers

such as Image Video or TSL, while maintaining remote control of the monitor’s settings and adjustments. The NCB-2010

is operated with a web interface via a standard TCP/IP network connection. No special application or additional software

is needed other than a standard web browser.

Features

■Full Remote Control

The NCB-2010 offers complete control of all monitor settings and adjustments, such as brightness, color, contrast,

aspect ratio, screen markers, curtain color, IMD text, etc.

■Control Entire Video Walls or Individual Monitors

The NCB-2010 can send global commands to affect all monitors in a video wall, or individual commands to affect

single monitors identified by ID#.

■Support for Third Party UMD Protocols

The NCB-2010 accepts and transmits Image Video or TSL v.3.1 and v4.0 protocol commands, while maintaining full

remote control of the monitors settings and adjustments.

■No Additional Software Needed

As the NCB-2010 is operated with a built-in web interface via a standard TCP/IP network, no special application or

additional software is needed other than a standard web browser.

Installation and Power-On

■Unpacking

Carefully unpack the NCB-2010 and verify that the following items are included:

• NCB-2010 Network Control Box

• V-PS12-5V-1 Power Supply with 2-Pin Twist Lock Connector

• Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,

immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,

call +1 (310) 333-0606.

■Rack Installation

The NCB-2010 can be mounted in any standard EIA 19” equipment rack. If additional equipment is installed directly

above and below the NCB-2010 in a rack, adequate ventilation of the rack is required to prevent overheating.

■Power-On Procedure

Plug the V-PS12-5V-1 power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist lock

connector to the back of the unit. Using the Power switch on the front of the unit, turn the NCB-2010 to the ‘ON’

position.

Allow the NCB-2010 to boot properly before attempting to access the Web Interface. During booting, the

READY LED will remain lit. On completion of the boot process, the READY light will blink.

READY

Help

The Help section contains Contact Information for Marshall Electronics, Inc.

Contact Information

The Contact Information page is shown below:

Please contact Marshall Electronics with any questions, comments or concerns.

Network

The Network Settings page is shown below:

oMAC Address –Indicates the MAC Address of your NCB-2010. This cannot be changed.

oIP Address – This field shows the current IP Address of the NCB-2010. You can change this by typing the

desired IP address in the text field and pressing Set below the Gateway field. You will be prompted to begin a

new instance of the NCB-2010 Web Interface with the new IP Address. Please consult your IT department for

information on valid IP address ranges on your network before you change this.

oBroadcast Address – This field shows the current Broadcast Address of the NCB-2010. You can change this by

typing the desired Broadcast address in the text field and pressing Set below the Gateway field. Please consult

your IT department for information on valid Broadcast addresses ranges on your network before you change this.

oNetmask – This field shows the current Netmask used by the NCB-2010. You can change this by typing the

desired Netmask in the text field and pressing Set below the Netmask field. Please consult your IT department

for information on selecting an appropriate Netmask.

oGateway – This field shows the current Gateway used by the NCB-2010. You can change this by typing the

desired Gateway in the text field and pressing Set below the Gateway field. Please consult your IT department

for information on selecting an appropriate Gateway.

Front and Rear Panel Features

POWER LED and Rocker Switch

The POWER LED indicates whether the NCB-2010

is in the ON or OFF state. The rocker switch

controls the power state of the NCB-2010. The

rocker switch is protected in order to avoid

accidental tripping of the switch.

RX – TX – READY LEDs

The Wall / Host RX and TX LEDs indicate whether

data is being received (RX) or transmitted (TX) by

the NCB-2010. The Wall RX / TX LEDs indicate that

information is being received and transmitted to IMD

equipped monitors. The Host RX LED indicates that

the NCB-2010 is receiving and transmitting

information. During the boot process, the READY

LED will remain lit. When the NCB-2010 is ready to

operate, the READY LED will blink.

RS-485 / 422 Port 1-4

The RS-485 / 422 ports send MEI protocol

commands to Marshall’s IMD line of monitors. Up to

128 screens can be connected to each port. These

ports also pass Image Video or TSL v3.1/v4.0

protocol commands from the RS-485 / 422 Port 5,

embedded in the MEI protocol.

RS-485 / 422 Port 5

The RS-485 / 422 port 5 is a Control Input that

receives Image Video or TSL v3.1 or v4.0 protocol

commands from an external controller. These

commands are then embedded in MEI protocol and

sent to the IMD monitors.

USB Peripheral Port

Use the USB peripheral ports to connect a USB

Mouse and USB keyboard to the NCB-2010 system

while in Console / Debugging mode.

Ethernet

The Ethernet port is an RJ-45 network interface used

to connected the NCB-2010 to a standard TCP/IP

network. The NCB-2010 is operated via an

embedded web interface

Console

The Console port is used for debugging purposes.

Please contact Marshall Electronics for instructions

on how to use this port.

Power Input

Connect the 12VDC input to the 2-Pin twist lock

power input connector. Note that the NCB-2010 takes

about 3 minutes to start up after power on, before the

unit is functional.

IMPORTANT: If using a power source other than the

included power supply, be sure that the polarity of

the DC input is correct:

USB Peripheral Ports

Use the USB peripheral ports to connect a USB

Mouse and USB keyboard to the NCB-2010 system

while in Console / Debugging mode. This is also a

bootable USB port when used with a USB Memory

Stick containing NCB-2010 Firmware.

READY

Connecting to the NCB-2010

Overview

The NCB-2010 can be operated by any computer with a web browser, via a TCP/IP network connection. No additional

software is needed. The NCB-2010 may be connected directly to a single computer, or connected to a local area network

and accessed by multiple computers. The NCB-2010 is shipped with the default IP address 10.0.0.254.

The following procedures describe the two ways to connect to the NCB-2010.

Connecting the NCB-2010 to a Single Computer

To use the NCB-2010 for the first time, you will most likely need to connect the NCB-2010 directly to a single computer.

After this connection is made, you can change the unit’s IP address to be suitable for your network.

1. Connect the NCB-2010 to a Windows-based computer using a cross-over ethernet cable.

2. Supply power to the NCB-2010 with the included power supply. Set the rocker switch on the front of the unit to

ON (

3. In Windows, open the Network Connections control panel. (Start > Control Panel > Network Connections)

4. A Local Area Connection should be listed. Right-Click on Local Area Connection, and select Properties.

5. Scroll down the list in the Local Area Connection Properties, click on Internet Protocol (TCP/IP), and click the

Properties button. Before making any changes to your Internet Protocol properties, contact your IT

department for guidance.

6. The computer attached, either directly or indirectly, to the NCB-2010 will have to be setup with an IP Address

10.0.0.xxx, where xxx could be any number from 2 to 253 and Subnet mask 255.255.255.0, as shown in the

image below:

7. If your IP address is not obtained automatically, please note down your settings before making any changes.

Contact your IT department for assistance.

oHardware version – Provides the current Hardware version of the NCB-2010.

Device Info

The Device Info page is shown below:

The Message Box shows the current status of commands being sent and acknowledged, as well as any error messages.

oChange Current ID Name –Allows you to set a name to a particular monitor ID on the NCB-2010 target monitor

pull down menu by typing a name in the text field. Only one ID Name can be changed at one time. The monitor

selected in the target monitor pull down menu will be changed when the Set button is pressed.

oGet Version X – Retrieves the Software, Keypad, FPGA1 or FPGA2 versions of the monitor ID selected in the

target monitor pull down menu. This information can only be retrieved from one monitor at a time. If your monitor

does not have a second FPGA, the NCB-2010 will respond with an error.

oGet Protocol Version – Retrieve the Protocol version of the monitor ID selected in the target monitor pull down

menu. This section applies to the Marshall Electronics protocol version embedded in your Marshall Electronics

monitor.

oGet Keypad Version – Retrieve the Keypad version of the monitor ID selected in the target monitor pull down

menu.

oGet Model Number – Retrieve the monitor Model number of the monitor ID selected in the target monitor pull

down menu.

oProtocol Standby – This sets the monitor selected in the target monitor pull down menu on Protocol Standby, or

RS-422 Ignore mode. This will render your Marshall Electronics monitor unable to respond to any RS-485 / 422

command. A message will appear on your monitor screen indicating Protocol Standby. The monitor must be

physically reset in order to return normal operation.

oSystem Reset – Resets the monitor selected in the target monitor pull down menu.

oSet Power State – Sets the Power state, Off or On, of the monitor selected in the target monitor pull down menu.

System Logs

The System Logs page is shown below:

The System Logs page is a log of all Status and Error messages displayed by the NCB-2010 for the currently active

Web Interface Page. The Log is cleared from the Web Interface after the end of each session. Although the log is

cleared in the Web Interface, a permanent log is kept on board the NCB-2010’s memory. This permanent log can be

accessed for troubleshooting purposes.

Status

The Status section of the NCB-2010 Web Interface Menu allows you to retrieve information about the software and

hardware versions of the NCB-2010,

Network Control Box Info

The Network Control Box Info page, labeled System in the Web Interface Menu, is shown below:

The message boxes are populated automatically at the startup of the Web Interface. The message boxes show you the

following information:

oWeb version –Provides the current Web version of the NCB-2010.

oProtocol version – Provides the current implementation of the MEI Protocol in use on the NCB-2010.

oFirmware version – Provides the current Firmware version of the NCB-2010.

Connecting to the NCB-2010 (continued)

Connecting the NCB-2010 to a Single Computer (continued)

8. Click OK in the Internet Protocol (TCP/IP) Properties window, and then click Close in the Local Area

Connection Properties window.

9. Open any web browser application (Internet Explorer, Firefox, etc.)

10. Enter the NCB-2010 Web Interface address. In the default case, it is http://10.0.0.254/. Make sure the

READY LED is blinking on the NCB-2010 before attempting to access the web interface.

11. Please check that you have the Shockwave Flash Player plug-in (Version 10.0 or above) in order to use this

webpage. You may see the following prompt when accessing from your web browser:

12. Click OK after the system has requested settings, as shown below:

13. If all system settings are loaded correctly, the following dialog will appear. Click OK.

14. If successfully connected, the web interface of the NCB-2010 will be shown in the browser windows as shown

below.

*Note: After you have successfully connected to the NCB-2010, you may want to configure your NCB-2010 to work off of

a network. The next section will detail how to change your IP Address to facilitate connecting your NCB-2010 to a

Local Area Network.

Before you can connect to the NCB-2010 via a Local Area Network, the settings made to your computer’s Local Area

Connection properties for direct connection from your PC to the NCB-2010 may need to be undone. Please contact your

IT department if your normal Local Area Connection settings need to be recalled.

oKeypad Commands (Menu, Select, ↑, ↓, F1, F2, F3, F4, Power) – These commands simulate pressing keypad

buttons on a monitor. The entire on-screen menu can be navigated using these commands alone.

oColor, Brightness and Contrast (+, - , Default) – Use these commands to manually increment or decrement the

value of the corresponding control by 1 unit. Use the Default button to set these values to their default value.

oChannel 1/ SDI 1, Channel 2 / SDI 2, Channel 3, Channel 4, Quad / Layout, DVI – Use these settings to select

a particular channel to view in full-screen mode, or the Quad button to return to toggle between different Layouts.

Use the DVI button to toggle your Channel 4 between a regular input or the DVI-I input on your QV monitor, or to

select the DVI input on the DLW monitors. Please check the Operating Instructions of your monitor to determine

if you have access to all of these settings.

Ping Device

The Ping Device page is shown below:

oPing (Healthy, Warning, Critical) – Test a command and response with a monitor.

Presets

The Presets page is shown below:

Use the buttons shown above to load and save presets in each monitor. Note that these controls affect the presets in

each monitor only. There are no presets in the NCB-2010 itself.

oLoad (Load presets User1 – User6, or Factory Default Settings)

oSave (Save the current settings on each monitor to presets User1 – User6)

Inhaltsverzeichnis

Andere Marshall Electronics Steuereinheit Handbücher

Marshall Electronics

Marshall Electronics CV-RCP-100 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung