Martec UNO Series Bedienungsanleitung
UNO 275W Single Lamp Heater Installation Guide
Thanks for choosing our UNO series..
We strongly recommend that you read this manual carefully before installation.
www.martecaustralia.com.au
Model Parameter:
MBHU1LW 275W Single Lamp Heater White
Part List
Qty 1x Single lamp heater
Qty 1x 275W radiant heat lamp
Voltage 220V-240V 50Hz
Rating 275W max
Hole cut-out 145mm(6”)
Dimensions Dia 180mm
Projection below ceiling 25mm
Projection above ceiling 214mm
Specications
NB: The single lamp heater is designed for installation in the ceiling of
toilets and bathrooms. It provides both light and heat. Two or more
heaters may be required for large bathrooms.
•Attractive, ush tting units that scarcely protrude below the
ceiling
• Allows installation where the heat is required; above the
drying area or above the vanity or elsewhere depending on
the bathroom layout
• A semi-gloss white powder-coated rim surrounding the
incandescent mirror reector
Features
Wiring Diagram
Wiring
Remove cover from terminal
block.
Fg.1
Insert active, neutral and
earth wires and tighten the
terminal screws.
Fg.2
Replace cover from terminal
block.
Fg.3
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
WARNING
• Installation of product MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Warranty will be VOID if the unit has been tampered with damaging by accident, short circuited, loaded beyond rating or
damaged otherwise by improper operation.
• The warranty is VOID if product is not installed according to this installation guide.
2 Year In Home Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
How to Install
Step 1. Inspect ceiling cavity to ensure that electrical sub circuit wiring, water pipes and other services as well as ceiling timbers
are well clear of the intended position of the single lamp heater.
(NB: Ensure there is sucient clearance above the terminal block housing for two storey house.)
Step 2. Use template provided to cut a circular hole with a diameter of 145 mm.
Step 3. Remove packaging before installation.
Step 4. Connect cables .
Step 5. Be sure to replace the cover over the terminals.
Step 6. Insert the light bracket into the hole.
Step 7. Loosen the nut and move the bracket supplied to x the light rmly into place. Tighten the nut.
Step 8. Replace the reector cone and the lamp.
Aust/NZ Approval No.
SAA-210966-EA
Dieses Handbuch passt für folgende Modelle
1
Andere Martec Heizung Handbücher
Martec
Martec Thermo Series Bedienungsanleitung
Martec
Martec MBHL 1000W Bedienungsanleitung
Martec
Martec ASPIRE Bedienungsanleitung
Martec
Martec VAPOUR MBHV2000W Bedienungsanleitung
Martec
Martec Phoenix Mini Bedienungsanleitung
Martec
Martec Linear MBHL 1000W Bedienungsanleitung
Martec
Martec MBHL1000W Bedienungsanleitung
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung