Martin CX-2 Bedienungsanleitung

CX-2

user manual

P/N 35000080

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Parts key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Lamp installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AC power connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

DIP-switch settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Data connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Basic service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

reproduced, in any form or by any means, without

permission in writing from Martin Professional A/S,

Denmark.

Printed in Denmark.

P/N 35000080, Rev. B

CX-2 user manual Introduction 3

NTRODUCTION

Thank you for selecting the Martin CX-2. The CX-2 is an automated profile

spotlight designed for a 250 watt halogen source. It provides separate color and

gobo/effect wheels, continuous electronic dimming, adjustable focus, strobe

effects, and multiple control options.

CX-2 SAFETY INFORMATION

Warning! This product is for professional use only. It is not for

household use.

This product presents risks of lethal or severe injury due to fire and heat, electric

shock, and falls. Read this manual before powering or installing the fixture,

follow the safety precautions listed below and observe all warnings in this manual

and printed on the fixture. If you have questions about how to operate the fixture

safely, please contact your Martin dealer or call the Martin 24-hour service

hotline at +45 70 200 201.

To protect yourself and others from electric shock

• Disconnect the fixture from AC power before removing or installing the lamp,

fuses, or any part, and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual to a qualified technician.

• Never operate the fixture with missing or damaged lenses and/or covers.

4 Introduction CX-2 user manual

To protect yourself and others from burns and fire

• Never attempt to bypass the thermostatic switch or fuses. Always replace

defective fuses with ones of the specified type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at least 0.1

meters (4 inches) away from the fixture. Keep flammable materials well away

from the fixture.

• Replace the lamp if it becomes defective or worn out. When replacing the lamp,

allow the fixture to cool for at least 5 minutes before opening the fixture or

removing the lamp. Protect your hands and eyes with gloves and safety glasses.

• Do not illuminate surfaces within 0.3 meters (12 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Never place filters or other materials over the lens.

• The exterior of the fixture can reach temperatures up to 65° C (149° F). Allow the

fixture to cool for at least 5 minutes before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

To protect yourself and others from injury due to falls

• When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

UNPACKING

The packing material is carefully designed to protect the fixture during shipment -

always use it to transport the fixture.

The CX-2 comes with:

• 1 3-meter, 3-wire IEC power cable

• 1 user manual

CX-2 user manual Parts key 5

ARTS

KEY

1 focus lens

2 cover locks

3 air vent

4 safety cable holes

5 mounting bracket

6 air vents

7 AC input & main

fuse

8 DIP-switch

9 data output

10 data input

11 swivel locks

12 cooling fan

6 Lamp installation CX-2 user manual

AMP

INSTALLATION

The CX-2 uses a 24V, 250W ELC halogen lamp. Two models are available, an

economical 300 hour lamp from Philips and a high-output 50 hour lamp from

Osram. Installing any other lamp may damage the fixture.

Allow the lamp to cool for at least 5 minutes before packing and moving the

fixture. To avoid possible damage, remove the lamp when shipping the fixture.

To install a lamp in the CX-2

Warning! Always disconnect the

fixture from AC power

and allow the fixture to

cool for 5 minutes

before installing a new

lamp.

1 Disconnect the fixture from

AC power. If replacing a hot

lamp, allow it to cool for 5

minutes before removing the

cover. The lamp cools faster

with the cover in place.

2 Release the 4 cover locks by

turning them a quarter-turn

counterclockwise. Lift the cover straight off.

3 To remove the lamp, grasp it by the reflector and pull it out of the holder. Pull

the socket straight back off the metal pins. Do not pull the wires.

4 Push the socket fully onto the pins of the new lamp.

5 Gently push the lamp into the holder until it snaps into place.

6 Replace the top cover. To lock the 4 cover locks, turn them a half to a quarter

turn clockwise until you feel them click.

Do not overtighten

CX-2 user manual AC power connection 7

POWER

CONNECTION

Warning! For protection from dangerous electric shock, the fixture must

be grounded (earthed). The AC mains supply shall have

overload and ground-fault protection.

Important! Check voltage setting before applying power. Do not connect

the CX-2 to an electrical dimmer system: doing so can damage

the electronics.

Before use verify that the fixture’s power supply is correctly tapped for the local

AC voltage. The default voltage setting is printed on the serial number label near

the AC input. The “EU” version may be set to 230 or 245 V AC and the “US”

version may be set to 110 or 120 V AC. Use the setting that is closest to the local

supply voltage.

To change the voltage setting

1 Disconnect the fixture from AC power.

Release the 4 cover locks by turning

them a quarter-turn counterclockwise.

Lift the cover straight off.

2 Locate and disconnect plug PL124 on

the back edge of the printed circuit

board. It has red, yellow, and blue

wires.

3 To select 230 V AC (EU version) or 110

V AC (US version), flip and move the

plug

so that the

red

wire connects

to the

top

pin.

4 To select 245 V AC (EU version) or 120

V AC (US version), flip and move the

plug

down

so that the

red

wire

connects to the

bottom

pin.

5 Replace the top cover before applying

power.

red

Setting for

110 V (US) / 230 V (EU)

Setting for

120 V (US) / 245 V (EU)

8 AC power connection CX-2 user manual

To install a plug on the mains lead

The fixture’s mains lead must be fitted with a grounding-type cord cap that

fits your power distribution cable or outlet. Consult a qualified electrician if

you have any doubts about proper installation.

Important! Verify that the feed cables are undamaged and rated for the

current requirements of all connected devices before use.

• Following the cord cap manufacturer’s instructions, connect the yellow and

green wire to ground (earth), the brown wire to live, and the blue wire to

neutral. The table below shows some pin identification schemes.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

CX-2 user manual Installation 9

NSTALLATION

The CX-2 can be fastened directly to a suitable surface or to a rigging clamp by

means of its adjustable mounting bracket.

Do not lay the fixture flat on its mounting bracket

arms or position it so that there is less than 10 cm

(4 in.) clearance around the fan and air vents.

For maximum lamp life, do not place the fixture

directly on or beside a speaker cabinet or other

source of strong vibrations.

To rig the CX-2

Warning! Always use a secure means of secondary attachment. Block

access below the work area before proceeding.

1 Verify that the clamp (not included) is undamaged and can bear at least 10

times the fixture’s weight. Bolt the clamp securely to the bracket with a grade

8.8 (minimum) M12 bolt and lock nut, or as recommended by the clamp

manufacturer, through the 13 mm hole in the center of the mounting bracket.

2 If permanently installing the fixture, verify that the hardware (not included)

and mounting surface can bear at least 10 times the fixture’s weight. The four

6.2 mm holes and/or the 13 mm hole in the mounting bracket may be used.

3 Verify that the structure can support at least 10 times the weight of all

installed fixtures, clamps, cables, auxiliary equipment, etc.

4 Working from a stable platform, clamp or fasten the fixture to the structure.

5 Install a safety cable that can hold at least 10 times the weight of the fixture

through/over the support and through a hole in one of the aluminum arms.

6 Loosen the swivel locks and tilt the fixture to the desired angle. Turn the

swivel locks clockwise to tighten. If a swivel lock does not tighten fully, pull

the handle out, turn it counterclockwise, and retighten. Repeat as necessary.

7 Verify that the fixture is located at least 0.3 meters (12 in.) away from the

surface to be illuminated and at least 0.1 meters (4 in.) from any combustible

materials. Verify that the clearance around the fan and air vents is at least 0.1

meters (4 in.). Verify that there are no flammable materials nearby.

10 DIP-switch settings CX-2 user manual

DIP-

SWITCH

SETTINGS

This section describes how to select the DMX address and special settings using

the DIP-switch on the end panel.

Important! Disconnect the fixture from AC power before changing the

DIP-switch setting. Changes take effect after the fixture has

been turned off and back on.

DMX ADDRESS SELECTION

If the CX-2 is to be used with a DMX protocol controller, then the DIP-switch

must be set to a DMX control address. The address, also known as the start

channel, is the first channel used to receive instructions from the controller. The

CX-2 uses 4 channels for full DMX operation. For independent control, each

fixture must be assigned its own address and non-overlapping control channels.

Two CX-2s may share the same address only if they are to respond identically:

they will receive the same instructions and individual control will not be possible.

To set the DMX address

1 Select an address for the fixture on your controller.

2 Look up the DIP-switch setting for the address on page 11.

3 Disconnect the fixture from AC power.

4 Set pins 1 through 9 to the ON (1) or OFF (0) position as listed in the table.

5 Set pin 10 to the OFF position.

6 Set pin 11 to the OFF position for full 4-channel DMX operation or to the ON

position for 1-channel DMX operation.

Inhaltsverzeichnis

Andere Martin Scheinwerfer Handbücher

Martin

Martin MAC III PERFORMANCE Bedienungsanleitung

Martin

Martin MAC III PERFORMANCE Bedienungsanleitung

Martin

Martin MAC III AirFX Bedienungsanleitung

Martin

Martin MAC 500 Bedienungsanleitung

Martin

Martin Mania SCX600 Bedienungsanleitung

Martin

Martin MAC Quantum Profile Einrichtungshandbuch

Martin

Martin MX-4 Bedienungsanleitung

Martin

Martin MX-1 Bedienungsanleitung

Martin

Martin MAC Encore Performance Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Bedienungsanleitung

LIVARNO home

LIVARNO home 375304 2101 Originalbetriebsanleitung

Cameo

Cameo CLQS40WW Bedienungsanleitung

Leviton

Leviton Ellipsoid 5/50 Bedienungsanleitung

Monacor

Monacor img Stage Line PARL-56PDX/CR Bedienungsanleitung

Vector

Vector SL3AKV Bedienungsanleitung

Quantum

Quantum Q262 Betriebshandbuch

Philips

Philips Vari-lite VL3015LT Bedienungsanleitung

EUROSPOT

EUROSPOT C51 Bedienungsanleitung

DTS

DTS MINI BRICK ARC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Handbuch

ACME

ACME LED-MS350B Bedienungsanleitung

EuroLite

EuroLite Akku flat light 1 Bedienungsanleitung

Commercial Electric

Commercial Electric SPTM-1401 Bedienungsanleitung

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Bedienungsanleitung

Teknik

Teknik FLEXI Bedienungsanleitung

Craftsman

Craftsman CMXLSB10 Bedienungsanleitung

EuroLite

EuroLite LED SLS-144 UV Floor Spot Bedienungsanleitung