MARTINDALE CM57 Bedienungsanleitung

CM57 TRMS AC SMART

CLAMP MULTIMETER

INSTRUCTION

MANUAL

CM57 instruct rev1.indd 2 11/11/2015 13:59:34

ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING

Thank you for buying one of our products. For safety and a full understanding

of its benefits please read this manual before use. Technical support is

available from 01923 441717 and support@martindale-electric.co.uk

CONTENTS

1 Safety Information 1

1.1 Meaning of Symbols and Markings 1

1.2 Precautions 2

2 Introduction 4

2.1 Inspection 4

2.2 Description 4

2.3 Accessories 5

2.4 Battery Installation 5

3 Operation 6

3.1 General 6

3.2 Low Battery Indication 6

3.3 Description of Clamp Meter Elements 6

3.4 Description of Press Buttons 7

3.5 Description of LCD Symbols 7

3.6 Auto Power Off 7

3.7 Backlight 8

3.8 Display Hold 8

3.9 Use of the TL16 Test Leads 8

3.10 AC Current Measurements 8

3.11 Voltage Measurements 9

3.12 Frequency Measurements 9

3.13 Resistance Measurements and Continuity Testing 10

3.14 Capacitance Measurements 10

3.15 Diode Testing 11

3.16 Use as a Non-contact Voltage Detector 11

4 Maintenance 12

4.1 Battery Replacement 12

4.2 Test Lead Replacement 13

4.3 Calibration 13

4.4 Cleaning 13

4.5 Repair & Service 14

4.6 Storage Conditions 14

5 Warranty 15

Measurement Categories 16

Specifications

CM57 instruct rev1.indd 3 11/11/2015 13:59:35

1. SAFETY INFORMATION: Always read before proceeding.

REMEMBER: SAFETY IS NO ACCIDENT

These instructions contain both information and warnings that are necessary

for the safe operation and maintenance of this product. It is recommended

that you read the instructions carefully and ensure that the contents are

fully understood. Failure to understand and to comply with the warnings and

instructions can result in serious injury, damage or even death.

Particular attention should be paid to the Warnings, Precautions and Technical

Speciﬁcations.

Please keep these instructions for future reference. Updated instructions and

product information are available at: www.martindale-electric.co.uk

1.1 Meaning of Symbols and Markings

Caution - risk of danger & refer to instructions

Caution - risk of electric shock

Equipment protected by double or reinforced insulation

(Class II)

Application around and removal from hazardous live

conductors is permitted.

CAT II (Measurement Category II) is applicable to test and measuring

equipment connected directly to utilization points (socket outlets

and similar points) of the low-voltage MAINS installation.

CAT III (Measurement Category III) is applicable to test and measuring

equipment connected to the distribution part of the building’s low-

voltage MAINS installation.

CAT IV (Measurement Category IV) is applicable to test and measuring

equipment connected at the source of the building’s low-voltage

MAINS installation.

CM57 instruct rev1.indd 6 11/11/2015 13:59:36

For further information on measurement categories see page 16 or visit

www.martindale-electric.co.uk/measurement_categories.php

Equipment complies with relevant EU Directives

End of life disposal of this equipment should be in

accordance with relevant EU Directives

1.2 Precautions

This product has been designed with your safety in mind, but

please pay attention to the following warnings and cautions before

use.

Warnings

In order to avoid the danger of electrical shock, it is important that

proper safety measures are taken when working with voltages

exceeding 30V AC rms, 42V AC peak or 60V DC.

Where applicable other safety measures such as the use of

protective gloves, goggles etc. should be employed.

The clamp meter must only be used by a skilled and competent

person who is familiar with the relevant regulations, the safety risks

involved and the consequent normal safe working practices, and

under the conditions and for the purposes for which it has been

constructed and specified.

Before each use the clamp meter and any associated test leads

and accessories should be examined for damage, cracks, cuts or

scratches. Do not use if damaged in any way.

CM57 instruct rev1.indd 7 11/11/2015 13:59:36

Make sure the clamp meter and test leads are dry, clean and free

from dust, grease and moisture while in use to avoid the danger

from electric shock due to surface leakage.

Always test this unit on an appropriate proving device or a known

good voltage source before and after using it to determine if a

hazardous voltage exists in a circuit to be tested. Do not use the

unit if it does not function correctly during proving.

Measuring/testing for a voltage/current that exceeds the specified

limits of the unit may damage the unit and may expose the operator

to a shock hazard. Always check the unit’s specified limits before

use.

As a clamp meter or multimeter the unit must only be used on

CAT III and CAT II installations up to 600V to earth, and within the

operating temperature and humidity range specified.

If the removable probe tip caps are not fitted to the probes of the

test leads, their measurement category becomes CAT II 1000V,

and they must not be used on CAT III or CAT IV installations to

avoid the risk of shorting high energy circuits and arc flash.

When this unit is used in combination with test leads, the

measurement category of the combination is the lower

measurement category of either this unit or the test leads used.

Likewise if test lead accessories such as crocodile clips are also

used, the measurement category will be the lowest measurement

category in that combination.

Do not use if the battery compartment cover is not fitted.

CM57 instruct rev1.indd 10 11/11/2015 13:59:37

When using test leads, always keep your fingers behind the finger

guard on the test lead probe.

When positioning the clamp jaws around a hazardous live conductor

always keep your fingers behind the clamp safety protection barrier.

When making current measurements using the clamps, disconnect

the test leads from the clamp meter terminals.

Cautions

Avoid severe mechanical shock or vibration and extreme temperature.

When using test leads avoid excessive stresses to the cable entry

points at the probe and 4mm plug connector.

To avoid possible corrosion from leaking batteries, remove the

batteries when the unit is not in use for an extended period.

2. INTRODUCTION

2.1 Inspection

Examine the shipping carton for any sign of damage. Inspect the

unit and any accessories for damage. If there is any damage then

consult your distributor immediately.

2.2 Description

The Martindale CM57 has a SMART function that automatically

detects if AC or DC voltage is being measured when set to the

voltage function. The SMART function also automatically determines

if resistance or capacitance is being measured or if a diode is being

tested.

CM57 instruct rev1.indd 11 11/11/2015 13:59:37

The Martindale CM55 has the following measurement functions:

True rms AC current to 600A

True rms AC voltage to 600V

DC voltage to 600V

Resistance to 6M:

Capacitance to 600μF

Frequency to 100kHz

Continuity with audible indication

Diode testing

Further functions are:

Non-contact voltage detector

Display hold

Auto power off

Auto ranging

Display backlight

2.3 Accessories

The CM57 comes with the following accessories:

Carrying case

Set of TL16 test leads

2 x 1.5V AAA batteries

Instructions

2.4 Battery Installation

Refer to section 4.1 (Battery Replacement) for the battery

installation instructions.

CM57 instruct rev1.indd 14 11/11/2015 13:59:38

3. OPERATION

3.1 General

If the clamp meter displays OL then the measurement limits of the

range have been exceeded.

3.2 Low Battery Indication

If the symbol is displayed, the batteries need replacing as

measurement accuracy can no longer be guaranteed (see section

4.1 Battery Replacement).

3.3 Description of Clamp Meter Elements

Clamp current sensing jaws

NCV sensing area

Clamp safety protection barrier

Clamp trigger

Rotary function selector switch

Backlight button

Frequency selector button

Hold button

9 Liquid crystal display

10 COM input terminal

11 Positive input terminal

Figure 1

CM57 instruct rev1.indd 15 11/11/2015 13:59:38

3.4 Description of Press Buttons

Selects backlight

Selects frequency measurement

HOLD

Selects display hold

3.5 Description of LCD Symbols

Auto power off is activated

HDisplay hold is activated

Diode test function is selected

Continuity function is selected

SMART SMART function is active

Indicates AC measurement

Indicates DC measurement

A, V, :, k:, M:,

Hz, nF, μF Units of measurement being displayed

Indicates >30V present between terminals

Indicates low battery

3.6 Auto Power Off

If the clamp meter is inactive for a period of 10 minutes it will

automatically power off.

If any button is pressed after the clamp meter has automatically

powered off, the clamp meter will turn back on.

CM57 instruct rev1.indd 18 11/11/2015 13:59:39

To disable the auto power off function hold the or Hz button at

the same time as turning the rotary switch from OFF to any position.

The symbol will no longer be displayed on the LCD.

3.7 Backlight

Press the button to turn on the backlight. Press again to turn the

backlight off.

The backlight will automatically turn off after 30 seconds to con-

serve the battery.

3.8 Display Hold

To hold a displayed value, press the HOLD button. The LCD will

display HOLD.

Press again to exit display hold.

3.9 Use of the TL16 Test Leads

Before use, always check the continuity of the test leads.

Where access to test points may require extended probe tips, the

probe tip caps may be removed by gently pulling them forward until

they unclip from the probe body.

CAT III 1000V

CAT IV 600V

CAT II 1000V ONLY

DO NOT USE ON

CAT III or CAT IV

installations

3.10 AC Current Measurements

Set the rotary switch to the Aposition.

CM57 instruct rev1.indd 19 11/11/2015 13:59:39

Taking all necessary safety precautions, press the clamp meter trig-

ger to open the clamp jaws, position the jaws around the conductor

to be measured, and release the trigger to close the jaws.

Position the clamp meter so the conductor is central within the

clamp jaws.

Read the measured ac current from the display.

Note. Clamping around more than one conductor will result in an

incorrect measurement.

3.11 Voltage Measurements

Connect the black test lead to the COM terminal and the red test lead

to the terminal.

Set the rotary switch to the Vposition. The LCD will display

SMART.

The smart function will automatically detect if an AC or DC voltage

is present at the terminals.

Taking all necessary safety precautions connect the test leads

to the circuit being measured and read the measured AC or DC

voltage from the display.

3.12 Frequency Measurements

When measuring AC current or AC voltage, the frequency of the

current or voltage can be measured by pressing the Hz button. The

LCD will display kHz.

To revert back to current or voltage measurement, press the Hz

button again.

CM57 instruct rev1.indd 22 11/11/2015 13:59:40

3.13 Resistance Measurements and Continuity Testing

Connect the black test lead to the COM terminal and the red test lead

to the terminal.

Set the rotary switch to the :position. The LCD will

display SMART.

Taking all necessary safety precautions connect the test leads to

the circuit being measured or tested.

The smart function will automatically detect if resistance is present

at the terminals.

Read the measured resistance from the display.

If the resistance is d30:, the buzzer will sound continuously.

3.14 Capacitance Measurements

Be sure the capacitor being tested is completely discharged

before connecting the test leads.

Connect the black test lead to the COM terminal and the red test lead

to the terminal.

Set the rotary switch to the :position. The LCD will

display SMART.

Taking all necessary safety precautions connect the test leads to

the circuit being measured.

The smart function will automatically detect if capacitance is

present at the terminals.

Read the measured capacitance from the display.

CM57 instruct rev1.indd 23 11/11/2015 13:59:40

3.15 Diode Testing

If the diode to be tested is in circuit, be sure the circuit power is

switched off.

Connect the black test lead to the COM terminal and the red test

lead to the terminal.

Set the rotary switch to the :position. The LCD will

display SMART.

Taking all necessary safety precautions connect the test leads to

the diode being tested.

The smart function will automatically detect if a diode is present at

the terminals.

If the diode is good a forward bias will give a display reading of

around 0.6 V (silicon diode) and a reverse bias will give a display

of OL. If the diode is shorted or open circuit the display will indicate

approx. 0V or OL respectively for both forward and reverse bias.

3.16 Use as a Non-contact Voltage Detector

Non-contact voltage detector testing is not suitable to

determine if a circuit is not hazardous live. A double pole

voltage test should always be used for that purpose.

Before and after each use, the non-contact voltage detector func-

tion must be proven using a suitable proving device or a known

good voltage source. Do not use if the unit fails to operate correct-

ly during proving.

Set the rotary switch to the NCV position. The LCD will display EF.

CM57 instruct rev1.indd 24 11/11/2015 13:59:40

Position the area of the clamp jaw marked NCV between the

marks toward the conductor to be tested for the presence of a live

voltage.

As the source of a live voltage is approached the buzzer will sound

intermittently and “-” will be displayed on the LCD.

Depending on the voltage level, the closer the proximity of the unit

to the voltage source, the more rapidly the buzzer sounds, until it

become continuous. The display will change from “-” to “- - - -” one

step at a time.

4. MAINTENANCE

4.1 Battery Replacement

To avoid shock or injury, disconnect the clamp meter from

any external circuits and remove the test leads before

proceeding.

Referring to figure 2, the battery compartment is underneath the

unit and can be accessed by removing the screw and lifting off the

cover.

Figure 2

CM57 instruct rev1.indd 21 11/11/2015 13:59:40

Fit 2 new 1.5V, AAA alkaline batteries (IEC LR03, NEDA 24A)

observing correct polarity.

Replace the battery compartment cover and screw.

Note: Do not mix old and new batteries.

4.2 Test Lead Replacement

If the test leads become damaged they should be replaced.

The replacement test leads must have the same (or better)

overvoltage category rating as the TL16 test leads supplied.

4.3 Calibration

To maintain the integrity of measurements made using your

instrument, Martindale Electric recommends that it is returned

at least once a year to an approved Calibration Laboratory for

recalibration and certification.

Martindale Electric is pleased to offer you this service.

Please contact our Service Department for details.

Email: [email protected]

Tel: 01923 650660

4.4 Cleaning

To reduce the risk of surface leakage, this instrument must be

kept in a clean condition.

Prior to cleaning, ensure that the instrument is disconnected

from any voltage source.

If contamination is found, clean with a damp soft cloth and if

necessary a mild detergent or alcohol. Do not use abrasives,

CM57 instruct rev1.indd 20 11/11/2015 13:59:39

abrasive solvents, or detergents which can cause damage to the

unit. If a mild detergent is used, the unit should subsequently be

thoroughly cleaned with a water dampened soft cloth. After cleaning,

dry and allow to remain in a dry environment for 2 hours before use.

4.5 Repair & Service

There are no user serviceable parts in this unit other than those that

may be described in section 4. Return to Martindale Electric if faulty.

Our service department will quote promptly to repair any fault that

occurs outside the guarantee period.

Before the unit is returned, please ensure that you have checked the

unit, batteries, leads and for poor connections.

4.6 Storage Conditions

The instrument should be kept in warm dry conditions away from

direct sources of heat or sunlight, and in such a manner as to

preserve the working life of the unit. It is strongly advised that the

unit is not kept in a tool box where other tools may damage it.

CM57 instruct rev1.indd 17 11/11/2015 13:59:39

5. WARRANTY AND LIMITATION OF LIABILITY

This Martindale product is warranted to be free from defects in material

and workmanship under normal use and service. The warranty period

is 2 years and begins on the date of receipt by the end user. This

warranty extends only to the original buyer or end-user customer,

and does not apply to fuses, disposable batteries, test leads or to any

product which, in Martindale’s reasonable opinion, has been misused,

altered, neglected, contaminated, or damaged by accident or abnormal

conditions of operation, handling or storage.

Martindale authorised resellers shall extend this warranty on new and

unused products to end-user customers only but have no authority to

extend a greater or different warranty on behalf of Martindale.

Martindale’s warranty obligation is limited, at Martindale’s option, to refund

of the purchase price, free of charge repair, or replacement of a defective

product which is returned to Martindale within the warranty period.

This warranty is the buyer’s sole and exclusive remedy and is in lieu

of all other warranties, expressed or implied, including but not limited

to any implied warranty of merchantability or fitness for a particular

purpose. Martindale shall not be liable for any special, indirect, incidental

or consequential damages or losses, including loss of data, arising from

any cause or theory.

Since some jurisdictions do not allow limitation of the term of an implied

warranty, or exclusion or limitation of incidental or consequential

damages, the limitations and exclusions of this warranty may not apply

to every buyer. If any part of any provision of this warranty is held invalid

or unenforceable by a court or other decision-maker of competent

jurisdiction, such holding will not affect the validity or enforceability of

any other provision or other part of that provision.

Nothing in this statement reduces your statutory rights.

CM57 instruct rev1.indd 16 11/11/2015 13:59:39

CM57 instruct rev1.indd 13 11/11/2015 13:59:38

Specification

CM57

AC Smart Clamp Multimeter

ELECTRICAL

All specified accuracies are at 23°C ± 5°C, <80% RH for 1 year.

Temperature coefficient: Add 0.1 x (specified accuracy) per °C. (0°C to 18°C,

28°C to 40°C).

All accuracies below are expressed as ± (percentage of reading + digits)

DC Voltage

Range Resolution Input

impedance Accuracy

6V 0.001V

10M:1.0% + 360V 0.01V

600V 0.1V

Overload protection: 660V DC or AC rms

AC Voltage

Range Resolution Input

impedance

Accuracy

(50 to 400Hz)

6V 0.001V

10 M:1.2% + 560V 0.01V

600V 0.1V

CM57 instruct rev1.indd 12 11/11/2015 13:59:37

Minimum AC voltage measurement: 0.3V rms

Crest factor: <1.8

Overload protection: 660V DC or AC rms

AC Current

Range Resolution

Accuracy

(50 to 60Hz) (60 to 400Hz)

60A 0.01A

1.9% + 5 3.0% + 5

600A 0.1A

Crest factor: <1.8

Overload protection: 660A DC or AC rms

Resistance

Range Resolution Open circuit

voltage

Accuracy

600:0.1:

-1.5V DC

1.2% + 3

6k:0.001k:

60k:0.01k:

600k:0.1k:

6M0.001M

Overload protection: 450V DC or AC rms

Continuity

Open circuit voltage Audible indication

-1.5V DC d30:

Overload protection: 450V DC or AC rms

Specification

CM57

AC Smart Clamp Multimeter

CM57 instruct rev1.indd 9 11/11/2015 13:59:36

Frequency

Measurement

function Range Resolution

Sensitivity Accuracy

AC current

6kHz

0.001kHz

3A rms

0.2% + 2

10kHz

0.01kHz

5A rms

AC voltage

6kHz

0.001kHz

5V rms60kHz

0.01kHz

100kHz

0.1kHz

Capacitance

Range Resolution Max. test

voltage

Accuracy

6nF 0.001nF

-1.5V DC

3.0% + 30

60nF 0.01nF

3.0% + 10

600nF 0.1nF

6μF 0.001μF

60μF 0.01μF

600μF 0.1μF

Minimum capacitance measurement: 0.3nF

Overload protection: 450V DC or AC rms

Non-Contact Voltage Indicator

Range: 90V to 600V (50Hz to 60Hz).

Specification

CM57

AC Smart Clamp Multimeter

CM57 instruct rev1.indd 8 11/11/2015 13:59:36

Diode Test

Resolution Max test current Test voltage

1mV <1mA <1.2V

Overload protection: 450V DC or AC rms

GENERAL

Display: Liquid crystal display with maximum reading 5999

Sample rate 2 times/sec

Polarity: automatic, positive implied, ‘-‘ for negative polarity

indication

Overrange: (OL) is displayed

Power: 2 x 1.5V, AAA alkaline batteries (IEC LR03, NEDA 24A)

Battery life (alkaline): 160 hours typical

Low battery indication: symbol is displayed

Auto power off: after 10 minutes

Jaw opening capability: 25.4mm

Dimensions: 203 x 75 x 32mm

Weight: 270g approx, including batteries

Includes: carrying case, set of TL16 test leads, 2 x 1.5V AAA batteries,

instructions

ENVIRONMENTAL

Temperature & Humidity

(Operating): 0°C to 40°C <80% R.H., non-condensing

(Storage): -10°C to 60°C < 70% R.H., batteries removed

Altitude: up to 2000m

Pollution degree: 2

SAFETY

Conforms to: BS EN 61010-1, BS EN 61010-2-032, CAT III 600V

Class II, double insulation

Specification

CM57

AC Smart Clamp Multimeter

CM57 instruct rev1.indd 5 11/11/2015 13:59:36

EMC

Conforms to BS EN 61326-1

SPECIFICATION FOR TL16 TEST LEADS

Maximum voltage: 1000V AC/DC

Maximum current: 10A continuous

Connector: 4mm banana plug with fixed shroud

Environmental

Temperature (Operating & Storage): 0°C to 40°C

Altitude: up to 2000m

Pollution degree 2

Safety

Conforms to BS EN 61010-031, CAT IV 600V, CAT III 1000V, 10A (Probe tip

covers fitted)

CAT II 1000V, 10A (Probe tip covers

removed)

Class II, double insulation

Specification

CM57

AC Smart Clamp Multimeter

CM57 instruct rev1.indd 4 11/11/2015 13:59:35

17th Edition Testers

Accessories

 Calibration Equipment

Continuity Testers

Electricians’ Kits

Environmental Products

Full Calibration & Repair Service

Fuse Finders

Digital Clamp Meters

Digital Multimeters

Labels

Microwave Leakage Detectors

Motor Maintenance Equipment

Multifunction Testers

Non-trip Loop Testers

Pat Testers & Accessories

Phase Rotation Testers

Proving Units

Socket Testers

Thermometers & Probes

Test Leads

Voltage Indicators

Specialist Metrohm Testers (4 & 5kV)

Specialist Drummond Testers

Check out what else you can get from Martindale:

Registered in England No. 3387451. Rev1 LITCM57

CM57 instruct rev1.indd 1 11/11/2015 13:59:18

Martindale Electric Company Limited

Metrohm House, Imperial Park, Imperial Way,

Watford, Hertfordshire, WD24 4PP, UK

Tel: +44 (0)1923 441717 Fax: +44 (0)1923 446900

E-mail:[email protected]

Website: www.martindale-electric.co.uk

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MARTINDALE Multimeter Handbücher

MARTINDALE

MARTINDALE VERITEST 2240 Bedienungsanleitung

MARTINDALE

MARTINDALE MM34 Bedienungsanleitung

MARTINDALE

MARTINDALE AM5 Bedienungsanleitung

MARTINDALE

MARTINDALE MM47 Bedienungsanleitung

MARTINDALE

MARTINDALE MM45 Bedienungsanleitung

MARTINDALE

MARTINDALE MM35 Bedienungsanleitung

MARTINDALE

MARTINDALE MM65 Bedienungsanleitung

MARTINDALE

MARTINDALE MM42 Bedienungsanleitung

MARTINDALE

MARTINDALE MM68 Bedienungsanleitung

MARTINDALE

MARTINDALE MM39 Bedienungsanleitung

MARTINDALE

MARTINDALE MM84 Bedienungsanleitung

MARTINDALE

MARTINDALE CM56 Bedienungsanleitung

MARTINDALE

MARTINDALE MM44 Bedienungsanleitung

MARTINDALE

MARTINDALE MM64 Bedienungsanleitung

MARTINDALE

MARTINDALE MM94 Bedienungsanleitung

MARTINDALE

MARTINDALE MM37 Bedienungsanleitung

MARTINDALE

MARTINDALE MM84 Bedienungsanleitung

MARTINDALE

MARTINDALE CM54 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung