Maruson TAC-HV1K Bedienungsanleitung

TACOMA HV SERIES

1K ~ 3KVA

On-Line UPS

USER MANUAL

Maruson Technology Corporation

P.O. Box1986, Walnut, CA91788 USA

Toll Free: 1-888-MARUSON

Website: www.MarusonUSA.com | E-Mail: Info@MarusonUSA.com

(U.S.TrademarkReg. No.3,150,957). Allothertrademarksarethepropertyoftheirrespectiveowners.

Productspecifications are subject to change without notice. Battery backup time is based on half load

and varies with equipment, configuration, battery age, temperature, etc.

CONTENT

1. Safety and EMC Instructions.....................................................1

1.1 Installation.........................................................................................1

1.2 Operation..........................................................................................2

1.3 Maintenance, servicing and faults....................................................3

1.4 Transport...........................................................................................4

1.5 Storage .............................................................................................4

1.6 Standards..........................................................................................5

2. Description of Commonly Used Symbols...................................6

3. Introduction .............................................................................7

4. Panel Description.....................................................................8

5. Connection and Operation ......................................................12

5.1 Inspection: ......................................................................................12

5.2 Connection:.....................................................................................12

5.3 Battery charge: ...............................................................................14

5.4 Turn on the UPS:............................................................................14

5.5 Test function:...................................................................................15

5.6 Turn off the UPS:............................................................................15

5.7Audible alarm mute function:..........................................................16

5.8 Operationprocedure of external battery for long backup time model

(“L” model) ............................................................................................16

6. Operating Mode for All Models ................................................18

6.1 Line mode.......................................................................................18

6.2 Battery mode ..................................................................................19

6.3 Bypass mode..................................................................................21

6.4 NO output mode.............................................................................21

6.5 EPO (Emergency Power Off).........................................................22

6.6 ECO mode (Economy mode).........................................................22

6.7 Converter mode..............................................................................23

6.8Abnormal mode ..............................................................................23

7. Setting by LCD Module...........................................................24

8. Trouble Shooting....................................................................27

9. Maintenance ..........................................................................31

9.1 Operation........................................................................................31

9.2 Storage ...........................................................................................31

9.3 Battery Replace..............................................................................31

10. Technical Data......................................................................32

10.1 Electrical specifications................................................................32

10.2 Operating Environment ................................................................32

10.3Typical backup time (Typical values at 25°C in minutes:)................33

10.4 Dimensions and weights ..............................................................33

11. Communication Port .............................................................34

11.1 USB...............................................................................................34

11.2AS400 Interface (Option)..............................................................34

12. Software...............................................................................35

Appendix: Rear panel.................................................................36

614-06810-02

1. Safety and EMC Instructions

Please read carefully the following user manual and the

safety instructions before installing the unit or using the unit!

1.1 Installation

See installation instructions before connecting to the supply.

Condensation may occur if the UPS is moved directly from a cold

to a warm environment. The UPS must be absolutely dry before

being installed. Please allow an acclimatization time of at least

two hours.

Do not install the UPS near water or in damp environment.

Do not install the UPS where it would be exposed to direct

sunlight or near heat.

Do not connect appliances or items of equipment which would

overload the UPS (e.g. laser printers, etc) to the UPS output.

Place cables in such a way that no one can step on or trip over

them.

Assure to connect withthe earth reliably.

Assure external battery source must be earthed.

Connect the UPS only to an earthed shockproof socket outlet.

The building wiring socket outlet (shockproof socket outlet) must

be easily accessible to close to the UPS.

With the installation of the equipment, the sum of the leakage

current of the UPS and the connected load does not exceed

3.5mA.

Do not block ventilation openings in the UPS’s housing. Ensure

the air vents on the front, side and rear of the UPS are not

blocked. Allow at least 25cm of space on each side.

UPS has provided earthed terminal, in the final installed system

configuration, equipotential earth bonding to the external UPS

battery cabinets.

An appropriate disconnect device as short-circuit backup

protection should be provided in the building wiring installation.

Please see the disconnect device specification in chapter 5.2.

Equipment the powered more than one source.

1.2 Operation

Do not disconnect the mains cable on the UPS or the building

wiring socket (grounded shockproof socket) during operation as

this would remove the ground to the UPS and of all connected

loads.

The UPS features its own, internal current source (batteries). You

may be electric shock when you touch the UPS output sockets or

output terminal block even if the UPS is not connected to the

building wiring socket.

In order to fully disconnect the UPS, first press the OFF button to

turn off the UPS, then disconnect the mains lead.

Ensure that no liquid or other foreignobjects can enter the UPS.

Back View of 3K

Back View of 3KL

Breaker(16A)

USB

EPO

Cooling Fan

Input Socket(16A)

Intelligent Slot

Battery connector

Output Socket

Fuse

Output Terminal

Breaker(20A)

USB

EPO

Cooling Fan

Input Terminal

Intelligent Slot

Battery connector

Output Socket

Fuse

Output Terminal

Appendix: Rear panel

Back View of 1K(L)

Back View of 2K(L)

Breaker

USB

EPO

Cooling Fan

Input Socket

Intelligent Slot

Battery connector

Output Socket

Breaker

USB

EPO

Cooling Fan

Input Socket

Intelligent Slot

Battery connector

Output Socket

Do not remove the enclosure. This system is to be serviced by

qualified service personnel only.

Remove the protective panelonly after disconnecting the terminal

connections.

Use No. 12 AWG (for 2-3K/KLinput wire) , 90¡C copper wire and

4.4 lb-in Torque force when connecting to terminal block.

Use No. 12AWG (for 2K/KL output wire) and No. 8AWG (for

3K/KL output wire), 90¡C copper wire and 12 lb-in Torque force

when connecting to terminal block.

1.3 Maintenance, servicing and faults

The UPS operates with hazardous voltages. Repairs may be

carried out only by qualified maintenance personnel.

Caution - risk of electric shock. Even after the unit is

disconnected from the mains power supply (building wiring

socket), components inside the UPS are still connected to the

battery which are potentially dangerous.

Before carrying out any kind of service and/or maintenance,

disconnect the batteries. Verify that no current is present and no

hazardous voltage exists in the capacitor or BUS capacitor

terminals.

Batteries must be replaced only by qualified personnel.

Caution - risk of electric shock. The battery circuit is not isolated

from the input voltage. Hazardous voltages may occur between

the battery terminals and the ground. Verify that no voltage is

present before servicing!

Batteries have a high short-circuit current and pose a risk of

shock. Take all precautionary measures specified below and

any other measures necessary when working with batteries:

remove all jewellery, wristwatches, rings and other metal

objects

use only tools with insulated grips and handles.

When changing batteries, replace with the same quantity and the

same type of batteries.

Do not attempt to dispose of batteries by burning them. It could

cause explosion.

Do not open or destroy batteries. Effluent electrolyte can cause

injury to the skin and eyes. It may be toxic.

Please replace the fuse only by a fuse of the same type and of

the same amperage inorder to avoid fire hazards.

Do not dismantle the UPS, except the qualified maintenance

personnel.

1.4 Transport

Please transport the UPS only in the original packaging (to

protect against shock and impact).

1.5 Storage

The UPS must be stockpiled in the room where it is ventilated

and dry.

12. Software

Free Software Download – WinPower

WinPower is a brand new UPS monitoring software, which provides

user-friendly interface to monitor and control your UPS. This unique

software provides safely auto shutdown for multi-computer systems while

power failure. With this software, users can monitor and control any UPS

on the same LAN no matter how far from the UPSs.

Installation procedure:

1. Go to the website:

http://www.ups-software-download.com/

2. Choose the operation system you need and follow the instruction

described on the website to download the software.

3. When downloading all required files from the internet, enter the serial

No: 511C1-01220-0100-478DF2A to install the software.

When your computer restarts, the WinPower software will appear as a

greenplug icon located in the system tray, near the clock.

11. Communication Port

The communication port is for the monitoring software. A USB port

and anintelligent slot are provided.

11.1 USB

The USB port is compliance with USB 1.1 protocol.

11.2 AS400 Interface (Option)

Except for the communication protocol as mentioned above, this

series UPS has AS400 card (an optional accessory) for AS400

communication protocol. Please contact your local distributor for

details. The following is the pin assignment and description of DB-9

connector inAS400 card.

Pin #

Description I/O Pin #

Description I/O

1 UPS Fail Output 6 Bypass Output

2 Summary Alarm

Output 7 Battery Low Output

3 GND Input 8 UPS ON Output

4 Remote

Shutdown Input 9 Line Loss Output

5 Common Input

DB-9 Interface of AS400 communication protocol

1.6 Standards

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission.................................:IEC/EN 62040-2 Category C1

Radiated Emission....................................:IEC/EN 62040-2 Category C1

Harmonic Current....................................:IEC/EN 61000-3-2

Voltage Fluctuation and Flicker...............:IEC/EN 61000-3-3

*EMS

ESD........................................................:IEC/EN 61000-4-2 Level 4

RS..........................................................:IEC/EN 61000-4-3 Level 3

EFT.........................................................:IEC/EN 61000-4-4 Level 4

SURGE..................................................:IEC/EN 61000-4-5 Level 4

CS………………………………….....…...:IEC/EN 61000-4-6 Level 3

MS………………………………....……..: IEC/EN 61000-4-8 Level 3

Voltaje Dips………………………...…...: IEC/EN 61000-4-11

Low Frequency Signals..........................:IEC/EN 61000-2-2

2. Description of Commonly Used Symbols

Some or all of the following symbols may be used in this manual. It is

advisable to familiarize yourself with them and understand their

meaning:

10.3 Typical backup time (Typical values at 25°C in minutes:)

Model No. 100 % Load 50 % Load

1K 5 14

2K 9 21

3K 5 15

10.4 Dimensions and weights

Model No. Dimensions W×D×H (mm) Net Weight (kg)

1K 145×400×220 13

1KL 145×400×220 7

2K 192×460×347 31

2KL 192×460×347 13

3K 192×460×347 31

3KL 192×460×347 13

10. Technical Data

10.1 Electrical specifications

INPUT

Model No. TAC-

HV1K

TAC-

HV1KL

TAC-

HV2K

TAC-

HV2KL

TAC-

HV3K TAC-

HV3KL

Phase Single

Frequency (45~55)/(54~66) Hz

Current(A) 5A 7A 9A 14A 14.5A 18A

OUTPUT

Model No. 1K(L) 2K(L) 3K(L)

Power rating

1kVA/0.8kW 2kVA/1.6kW 3kVA/2.4kW

Voltage 200/208/220/230/240×1 2% VAC

Frequency 50/60±0.2Hz (Battery mode)

Wave form sinusoidal

Derating to 90% when the output voltage is adjusted to 208VAC

Derating to 80% when the output voltage is adjusted to 200VAC

BATTERIES

Model No. 1K 2K 3K

Number and type

3×12V 7Ah 8×12V 7Ah 8×12V 7Ah

10.2 Operating Environment

Ambient Temperature 0oC to 45oC

Operating humidity < 95%

Altitude < 1000m

Storage temperature 0oC to 45oC

3. Introduction

This On-Line-Series is an uninterruptible power supply incorporating

double-converter technology. It provides perfect protection specifically

for Novell, Windows NT and UNIX servers.

The double-converter principle eliminates all mains power disturbances.

A rectifier converts the alternating current from the socket outlet to direct

current. This direct current charges the batteries and powers the

inverter. On the basis of this DC voltage, the inverter generates a

sinusoidal AC voltage, which permanently supplies the loads.

Computers and periphery are thus powered entirely by the mains

voltage. In the event of power failure, the maintenance-free batteries

power the inverter.

This manual covers the UPS listed as follows. Please confirm whether it

is the model you intend to purchase by performing a visual inspection of

the Model No. on the rear panel of the UPS.

“L” Model: Extended backup time

Model No. Type Model No. Type

1K 1KL

2K 2KL

3K Standard 3KL

Extended backup

time

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Maruson UPS Handbücher

Maruson

Maruson UltimaPro 33 Series Bedienungsanleitung

Maruson

Maruson Tacoma II Series Bedienungsanleitung

Maruson

Maruson POW-1100A Bedienungsanleitung

Maruson

Maruson POP-420B Bedienungsanleitung

Maruson

Maruson Ultima RT 6K Bedienungsanleitung

Maruson

Maruson PRO-550LCD Bedienungsanleitung

Maruson

Maruson Power Pro 650VA Bedienungsanleitung

Maruson

Maruson 1100 Bedienungsanleitung

Maruson

Maruson PowerPro 550VA Bedienungsanleitung

Maruson

Maruson POF-800A Bedienungsanleitung

Maruson

Maruson ULT-W1K Bedienungsanleitung

Maruson

Maruson Matrix VX33 Series Bedienungsanleitung

Maruson

Maruson SUR-809UPS Bedienungsanleitung

Maruson

Maruson 700 Bedienungsanleitung

Maruson

Maruson PRO- 650LCD Bedienungsanleitung

Maruson

Maruson PRO-400A LCD Bedienungsanleitung

Maruson

Maruson MIC-500A Bedienungsanleitung

Maruson

Maruson POF-800UA Bedienungsanleitung

Maruson

Maruson ULT-1K Bedienungsanleitung

Maruson

Maruson SmartDual Series Bedienungsanleitung

Maruson

Maruson Micro UPS Series Bedienungsanleitung

Maruson

Maruson CP-SV414-360W Bedienungsanleitung

Maruson

Maruson Ultima LiFe RT Series Bedienungsanleitung

Maruson

Maruson TACOMA LV Series Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung