Marvin Sliding Door Automatic Control Device Bedienungsanleitung
2022-09-08
19916437
Sliding Door Automatic Control Device
Installation Instructions
ABSTRACT: Use this site prep guide in conjunction with the Sliding Door Automatic Control Site Prep Instruction.
Install the door prior to installing the motor. The following instructions assume the installer has prior product and in-
stallation training before attempting to install the device.
IMPORTANT
The motor and control box are complete units and must not be disassembled in the field.
Table of Contents
Tools Needed .............................................................. 1
Door/Stud/Motor Cavity Prep ...................................... 2
Wiring Prep ................................................................. 3
Install the Pulley Corner Key....................................... 4
Install the Motor .......................................................... 5
Install the Control Box................................................. 7
Connecting Components............................................. 9
Threading the Belt......................................................11
Installing the Optional Closing Ramp ........................ 15
Optional Belt Clips..................................................... 16
Programming............................................................. 17
Reprogramming ........................................................ 18
Tools Needed
• 14 gauge cable crimper
• Wire stripper
• Power drill/driver
• 1 1/4" drill bit
• 7/64" drill bit
• 9/64" Allen Wrench
• 3/32" Allen wrench
• Measuring tape
• Heavy duty shear (for cutting the belt)
• Extended #2 Phillips bit
• Safety glasses
WARNING!
Always practice safety! Wear the appropriate eye, ear, and hand protection, especially when working with power
tools.
2022-09-08 2 Sliding Door Automatic Control Device
19916437 Installation Instructions
Door/Stud/Motor Cavity Prep
There are two options to consider when prepping the
stud cavity to accept the drive belt.
1. Option A: Drill into the stud adjacent to the interior
most track of the door with a 1 1/4" hole saw. See
Figure 1.
Figure 1
2. Option B: Measure the height of your door and cut a
1 1/4" x 2 1/2" deep notch lined up with the belt pass-
through on the corner key. When installation is
complete cover the notch with a steel tie plate. See
Figure 2.
Figure 2 Notched stud
1 1 3/4" on center lined up with the corner key.
1 Steel stud tie
2Notch
2022-09-08 3 Sliding Door Automatic Control Device
19916437 Installation Instructions
Wiring Prep
Wiring Included
The following supplies are included with your motor but may be supplied locally. If CAT5e cables are locally supplied
they MUST be shielded.
• 18" system power cable
• 100’ 14-2 motor power cable (cable crimps
included)
• 100’ and 10’ of red CAT5e "Super Cable"
• 75’ and 10’ of blue CAT5e cable
• 25’ of yellow CAT5e cable
Wiring Diagram
Figure 3
1 Motor
2 Control Box
3 110 volt outlet dedicated 15 amp circuit
4 Power cable from outlet to control box (if recessed, the control box must be hardwired).
5 Sensor 1
6 Sensor 2
7 Interior wall switch
8 Exterior wall switch
9 14-2 Power cable run from control box to motor.
10 Red CAT5e “Super Cable” run from the control box to motor.
11 Blue CAT5e cable ran from the interior and exterior wall switches to the motor or controller. (Can be daisy chained)
12 Yellow CAT5e cables ran from each sensor to the motor.
13 Power cable is supplied
2022-09-08 4 Sliding Door Automatic Control Device
19916437 Installation Instructions
Install the Pulley Corner Key
1. On ultimate MSD only: Remove the cover with a
9/64” Allen wrench. See Figure 4. Remove the bottom
washer, the pulley and top washer and set aside. See
Figure 5. This will give you access to the side screw
holes. Attach the pulley base with two #8 x 3" screws
into the side RO. See Figure 6. Replace the washers,
pulley and cover in the reverse order you removed
them.
Figure 4
Figure 5
Figure 6
2. Make sure the corners are properly shimmed near
the corners to support the corner key pulley fasteners.
3. Fasten the pulley corner key into the head jamb
rough opening with two #8 x 3" screws. provided.See
Figure 7.
Figure 7
1 #8 x 3" screws
2022-09-08 5 Sliding Door Automatic Control Device
19916437 Installation Instructions
Install the Motor
IMPORTANT
Check the door for proper operation before proceeding.
Make the sure the panels are square and operating
smoothly. Make sure you have proper head jamb clear-
ance above the panels for the belt to travel. Make sure
the locking hardware locks and engages properly.
Hint
You will align the motor so it is centered on the lead pan-
el. Mark a centerline in the motor cavity to aid installa-
tion. The front of the motor is the side with one stand-off
at the top of the motor.
1. Install a screw on their centerline within 3" of the stud
and leave the head proud about 3/4"-1".
Figure 8
2. Hang the motor by the slotted hole on the front edge
of the mounting plate. See Figure 9.
Figure 9
3. Pre-drill with a 7/64" drill bit and fasten the four
corners with #8x 3" screws provided
2022-09-08 6 Sliding Door Automatic Control Device
19916437 Installation Instructions
4. Set the motor drive pulley in line with the belt holes
and secure the two set screws with a 3/32" Allen
wrench. Adjust the pulley up or down until aligned. Then
tighten the set screws. This pulley can be adjusted later
to avoid belt rub.
IMPORTANT
Make sure there is clearance below the drive pulley.
(Note the area marked with a red arrow in Figure 10
(next page).
Figure 10 Drive pulley shown with belt attached
1 Set screws (2) are located at 90 degrees from each other
2022-09-08 7 Sliding Door Automatic Control Device
19916437 Installation Instructions
Install the Control Box
The control box can be located within 100’ of the motor.
Use an accessible, well lit location in an A/V closet or
utility room separate from the motor cavity. Mount the
control box chest high in a well lit space.
1. On the front of the control box, make sure the AC and
Battery switches are in the off position. See Figure 11.
Figure 11
2. Mount the box from the side or back using the
installation keyholes on the control box and the
installation screws provided. Use an extended #2
Phillips bit to aid in installation. When mounting on the
back start with the bottom left screw first. Fasten all
screws to securely mount the control box (4 screws for
rear mount, 2 screws for side mount). See Figure 12.
Figure 12 Rear mounting holes. Controller removed for illustra-
tive purposes only.
3. Determine which knockouts to remove to allow
power and CAT5e cables to enter the control box.
IMPORTANT
Make sure you leave some slack in the cables before
connecting to the control box. Make sure there are no
tight bends in any cable.
Figure 13
1 Knockouts
2022-09-08 8 Sliding Door Automatic Control Device
19916437 Installation Instructions
4. Pass the cables through the knockout and connect to
the correct receiver. Make the following connections in
the control box:
• Connect the white14 gauge wire to the A1 port and
the black 14 gauge wire to the A2 port.
• Connect the red CAT5e supercable to the
corresponding connectors from the motor.
• Connect the yellow CAT5e cable to the yellow port
on the motor.
• Connect the blue CAT5e cable to the blue port on
the control box or motor, whichever is more
accessible.
Figure 14 Control Box connections.
5. Remove the battery cover and battery from the
control box. Connect the two loose red battery cables
together to complete the circuit. Replace the battery and
battery cover/nut. See Figure 15 and Figure 16.
Figure 15
Figure 16
1 A1 and A2 ports--14 gauge wires from motor
2 Red CAT5e from motor
3 Blue CAT 5e (can be connected to control box or motor)
1 Battery cover nut
1 Battery cables.
2022-09-08 9 Sliding Door Automatic Control Device
19916437 Installation Instructions
6. Insert the AC power cord into the bottom of the
control box and plug the other end into a standard 110v/
15 amp dedicated circuit.
ATTENTION
The next step on hard wiring should only be done by a
licensed electrician.
7. Optional Hardwire: Remove the two screws from
the power port on the control box to access internal
wiring.
Connecting Components
1. Attach the blue female cable crimp connectors to the
14-2 cable from the control box. See Figure 17.
Figure 17
2. Control Box to Motor: the red Super Cable
connects to the corresponding port on the motor. Red
and black female leads from the motor to the black and
white male leads from the control box. See Figure 18.
Figure 18
3. Wall Switches: Connect the blue CAT5e from the
"out" port on the wall switch to the corresponding wall
switch port on the motor or control box. Additional wall
switches can be added to the “in” port on the wall switch
(daisy chain).
Figure 19
1 Ensure a solid crimp
1 Wall switch "out" port.
2022-09-08 10 Sliding Door Automatic Control Device
19916437 Installation Instructions
4. Sensors: connect the yellow CAT5e to the
corresponding sensor port on the motor. See Figure 19
and Figure 20.
Figure 20
5. Use double sided tape to attach to the sensor to the
head jamb cover. The sensor eye will fit through the
hole in the cover. See Figure 21.
Figure 21 Inset shows sensor eye through head jamb cover
1 Wall switch port on the motor
2 Sensor ports on the motor
1 Sensor through head jamb cover
Inhaltsverzeichnis
