Master Water Conditioning MP-MCA Series Bedienungsanleitung

January 2019

MP-MCA RESIDENTIAL

ANION UNITS

Installation and Operation Manual

www.masterwater.com

Installation and Operating Instructions for

MCA CONTROL VALVE

Top Mount Anion Resin Unit

Model #:

____ MP-MCAD-30T 1.0 CF Dealkalizer

____ MP-MCAD-45T 1.5 CF Dealkalizer

____ MP-MCAD-60T 2.0 CF Dealkalizer

____ MP-MCAN-30T CS Crawl Space Nitrate Removal

____ MP-MCAN-30T 1 CF Nitrate Removal

____ MP-MCAN-45T 1.5 CF Nitrate Removal

____ MP-MCAN-60T 2.0 CF Nitrate Removal

____ MP-MCAT-30T 1.0 CF Tannin Removal

____ MP-MCAT-45T 1.5 CF Tannin Removal

____ MP-MCAT-60T 2.0 CF Tannin Removal

____ MP-MCAU-30T 1 CF Uranium Removal

____ MP-MCAU-45T 1.5 CF Uranium Removal

____ MP-MCAU-60T 2.0 CF Uranium Removal

Shipping Carton Description / unit:

# of

cartons

Contents

Description

Mineral tank

Distributor pipe installed

Brine tank

*NOTE: MCA valve is shipped in brine tank.

MP MCA control

valve

MP MCA timer and backwash flow control

and bypass with tail piece kit

NOTE: THIS ANION UNIT IS NOT INTENDED TO BE USED FOR TREATING

WATER THAT IS MICROBIOLOGICALLY UNSAFE OR OF UNKNOWN QUALITY

WITHOUT ADEQUATE DISINFECTION WHETHER BEFORE OR AFTER THE SYSTEM

Anion Unit Positioning:

1. Place Anion unit in desired position, far enough from walls and

other obstructions to allow for servicing the unit.

2. Place the Anion unit within reasonable access to a grounded

115V/60 HZ circuit and a legal drain line connection.

MP-MCA Control Valve:

1. When facing the front of the MP-MCA timer, the inlet connection

is located on the right and the outlet connection is on the left.

The control valve's inlet and outlet connections are either 1”

copper or PVC equipped with split ring and nut.

Front View Top View

2. Turn the control valve upside down and ensure that the control

valve distributor o’ring is in place. Use silicone lubricant on the

o'ring.

**DO NOT USE PETROLEUM!**

**USE ONLY SILICONE **

3. Connect the D1255-03 strainer onto the control valve.

4. Place the control valve onto the distributor pipe and into the tank

opening.

5. Thread the control valve hand tight . Do not overtighten.

5. Locate the bypass valve assembly that is packaged with the

control valve. The bypass valve has two red handles that

indicate flow direction, two threaded connections for the tail

piece kit and two o’ring seal connections with nuts for the control

valve. Align the insert connection ends with o’ring seals and

nuts to the inlet and outlet connections of the control valve.

Hand tighten the nuts. DO NOT OVERTIGHTEN THE NUT!

Control Valve

6. Locate the tail piece kit that is packaged with the control valve.

Align a tail piece assembly to the bypass valve threaded inlet and

Outlet until the nut can be tightened. Hand tighten because

excessive tightening will damage the assembly. REPEAT THE

PROCEDURE FOR THE OUTLET CONNECTION.

Service and Drain Piping:

1. Pipe water combination unit into the service lines .The inlet and

outlet connections of the control valve are located on the back of

the valve body. As you face the timer the inlet is on the right and

the outlet is on the left. Always follow local plumbing codes when

installing our water treatment equipment.

2. If sweat fittings are used, be sure soldering is done in such a

manner as not to allow heat to reach the control valve or bypass.

(If Schedule 80 PVC is used make sure to follow the proper

primer and solvent instructions.)

3. The drain line connection is 5/8” OD or ¾” npt and is located on

the top left of the valve as you face the timer. It is recommended

you install a ¾” union on the drain line for servicing if not using

5/8 OD. The drain line must be of adequate size to allow for full

regeneration flow.

Control Valve

Bypass Valve

Tail piece assembly

•The control valve drain connection is 3/4" npt.

•Never decrease the drain piping size to below the

drain connection size.

•Maximum drain line length is 30 feet with proper

sloping the entire length.

•Maximum drain line height is 6 feet above the

control valve.

•The drain line must be piped to an open air gap

(See Figure above)

•Always follow local plumbing codes.

UNDER NO CIRCUMSTANCES SHOULD THERE BE A DIRECT

CONNECTION WITH SANITARY SEWAGE FACILITIES.

DRAIN LINE

CONNECTION

MASTER

Water Conditioning Corp.

Well Tank

NOTE: All Master Water Conditioners must be

installed after the well tank or water meter if its

public water supply.

Master Water

Conditioner

Brine tank

Air Gap Drain

Overflow

fitting to

floor drain

gravity

Untreated

Treated

Model #

Service

GPM

Backwash

GPM

Salt Required

per regeneration

Salt

Storage

Height

Diameter

MP-MCAN-30T CS

5-7.5

1.3

15 lbs.

300 lbs.

30.0”

10.0"

MP-MCAN-30T

5-7.5

1.3

15 lbs.

300 lbs.

48.0"

10.0"

MP-MCAN-45T

7.5-11.25

1.3

22.5 lbs.

400 lbs.

62.0”

12.0”

MP-MCAN-60T

10-15

1.7

30 lbs.

400 lbs.

56.0”

16.0”

MP-MCAU-30T

1.3

15 lbs.

300 lbs.

48.0"

10.0"

MP-MCAU-45T

1.3

22.5 lbs.

400 lbs.

62.0”

12.0”

MP-MCAU-60T

1.7

30 lbs.

400 lbs.

56.0”

16.0”

Electrical Requirements:

Always follow all local electrical codes when installing our water

treatment equipment.

1. Provide an 115v/60Hz properly grounded dedicated electrical

outlet. (It’s very important that the polarity be correct)

Avoid using outlets that are switch controlled.

2. Maximum amperage required is 5 amps.

3. Make sure the electrical service provides power 24 hours per day.

We recommend installing a surge protector to protect unit from

power surges, which are not covered by warranty.

Brine Tank:

1. The brine tank should be located directly beside the water Anion

unit mineral tank.

2. Connect the 3/8" poly tubing to the 3/8” black elbow quick-connect

fitting located on the top left side of the MCA control valve.

3. Place 2 gallons of water directly into the brine tank.

See Figure Below.

The brine tank is equipped with a shutoff valve, the float height

was preset at the factory.

3/8”BRINE LINE

CONNECTION

Filling Anion unit with Water:

1. Connect the MP-MCA control valve transformer into the electrical

outlet provided.

2. Press and hold the REGEN button until the drive motor starts.

When the drive motor stops, the display will read “BACKWASH”

position.

3. Open the inlet ball valve a ¼ turn of its full open position to allow

water to enter the Anion unit mineral tank slowly. The water is

going to enter the tank from the bottom of the distributor pipe and

leave the tank from the top. This will slowly purge all the air from

the tank.

IF WATER ENTERS THE TANK TOO FAST, ALL THE CATION

RESIN WILL BE FLUSHED TO DRAIN DURING START UP.

4. When only water is running to the drain, open the inlet and outlet

ball valves fully.

5. Press the REGEN again until the drive motor starts. When the

drive motor stops, the display will read “BRINE” position.

6. Press and hold the REGEN button until the drive motor starts.

When the drive motor stops, the display will read “RINSE” position.

The fast rinse position will rinse the combination unit tank.

7. The control valve will automatically advance to the brine refill

position where the brine tank will fill with the proper amount of

water. The display will read “FILL”.

NOTE: THE TIMER WILL AUTOMATICALLY ADVANCE TO THE

SERVICE POSITION AND THE DISPLAY WILL READ THE

CAPACITY REMAINING, IN GALLONS.

MP-MCA Control Valve Timer Settings:

Note: The control valve is set at the factory. You only need to set

the time of day , hardness and regeneration time if required, which is

preset at 2 am.

Time of Day Setting

1) Press the CLOCK button. The screen will show the Time of

Day and the hours will be blinking.

2) To change the hour, use the UP and DOWN arrows to set the

Hour.

3) To change the Minutes, press CLOCK, use the UP and

DOWN arrows to set the Minutes

4) Press the CLOCK button.

Hardness Setting (the factory default is 10)

1) Press the NEXT and UP arrow simultaneously for 3 seconds.

The screen will show the Hardness as grains per gallon in

blinking numbers.

2) To change the number, use the UP or DOWN arrows.

3) Press the NEXT button.

Note: 1 ppm tannin = 1 gpg of hardness.

5 ppm of Nitrate = 1 gpg of hardness.

5 ppm of Uranium = 1 gpg of hardness.

Regeneration Day Override Setting (the factory default is 7)

1) The screen will show the Regeneration Day Override in

blinking numbers.

2) To change the number, use the UP or DOWN arrows.

3) Press the NEXT button.

Time of Regeneration Setting (the factory default is 2 AM)

1) The screen will show the Time of Regeneration in blinking

numbers.

2) If Regeneration time change is desired, use the UP and

DOWN arrows to set the Hour.

3) To change the Minutes, press NEXT, use the UP and DOWN

arrows to set the Minutes

4) Press the NEXT button.

NOTE: SALT SETTING AND CAPACITY ARE PRESET AT THE

FACTORY.

Final Check:

1. Fill the brine tank with Solar Salt and the Res-Up Feeders with

Res-Up (one quart is provided).

2. Make sure the drain line connection meets all plumbing codes and

that the drain line size can handle the backwash flow rate of the

Tannin unit.

3. Make sure the Inlet and Outlet on the bypass valve are open.

4. Make sure the control valve timer is plugged into an electrical

outlet with power 24 hours per day.

5. Check all piping for leaks.

IMPORTANT NOTE:

The treated water alkalinity level will be slightly reduced by the

Anion unit which decreases the pH level of the water.

You should consider installing pH control after this unit; it could be

an acid neutralizer or chemical feed system.

We include a mixing valve to assist in blending treated and untreated

water to achieve the water quality desired and simultaneously

increase the alkalinity and pH. The mixing valve may have to remain

closed because of the severity of the water condition. In that case, if

pH is too low, then treatment would be required.

Dieses Handbuch passt für folgende Modelle

Andere Master Water Conditioning Wasserfiltersystem Handbücher

Master Water Conditioning

Master Water Conditioning PURO PRO 1800 SC Series Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning MP-NS-30T Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning Alliance MP-MCA Series Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning MBA-AN-10/13 Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning Clarifier MCA Series Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning MBA Series Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning SIMPLUS 744 Bedienungsanleitung

Master Water Conditioning

Master Water Conditioning FES-30T Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung