matev SRM-FB 130 Montageanleitung
matev GmbH
Nürnberger Str. 50
90579 Langenzenn
T +49 (0) 9101 9087 -0
F +49 (0) 9101 9087 -20
www.matev.eu
Version 01/2018
Original Operating Manual
SRM-FB 130 (131_8773)
SRM-FB 140 (131_8774)
SRM-FB 150 (131_8775)
SRM-FB 160 (131_8776)
Content
Page 2
Table of contents
1.1 About this operating manual........................................................................................3
2Safety.........................................................................................................................4
2.1 Intended use...............................................................................................................4
2.2 Qualification of personnel............................................................................................4
2.3 General safety instructions..........................................................................................4
2.4 Special safety instructions...........................................................................................5
3Installation.................................................................................................................6
3.1 Preparations on the snow blade..................................................................................6
3.2 Installation of pressure contol valve ............................................................................8
3.3 Attaching the snow blade on the tractor ......................................................................9
3.4 Adjustments on the snow blade ................................................................................13
4Operation and fault correction...............................................................................16
4.1 Operation..................................................................................................................16
4.2 Faults........................................................................................................................16
4.3 Contact .....................................................................................................................17
5Service.....................................................................................................................18
6Disposal...................................................................................................................20
7Guarantee................................................................................................................20
8Technical data and accessories.............................................................................20
8.1 Technical data...........................................................................................................20
9List of illustrations..................................................................................................21
10 EC Declaration of Conformity ................................................................................22
Safety
Page 3
1.1 About this operating manual
Dear customer!
Thank you for purchasing this implement, we appreciate your trust.
Prior to using this implement for the first time, read this operating manual carefully and
conscientiously all the way through.
Keep this operating manual where it is easily accessible. This will enable you to refer to
important information and handling instructions as needed.
Listings with bullet points are marked as follows:
•Text
•Text
•Text . . .
Handling instructions are marked in the sequence in which they should be executed, as
follows:
1. Text
2. Text
3. Text . . .
This implement is subject to change in the interest of technical progress. All
information, illustrations, and technical specifications represent the latest
status at the time this manual was published. The manufacturer reserves the
right to make changes at any time in the interest of technical progress.
Safety
Page 4
2 Safety
Guidelines and instructions with which you must comply, are summarized in this section.
Personnel who mount, operate and maintain this implement, must have read and under-
stood this operating manual.
2.1 Intended use
The snow blade is an implement for winter service and is used for clearing snow from
roads, paths, and other areas.
All other uses are excluded.
Non-intended use causes:
•Danger of injury to the operator or third parties
•Damage to the tractor and the implements
•Environmental damage
2.2 Qualification of personnel
Only personnel 18 years of age or older, or instructed personnel should install, operate,
and maintain the snow blade. The operator must have read and understood this operat-
ing manual.
2.3 General safety instructions
General safety instructions are explained in this section. These safety instructions are
used in the subsequent sections. In addition to the safety aspect, you will save money
and work time if you follow these safety instructions.
Danger!
Severe injury to the operator or third parties can occur.
Follow the safety instruction.
Attention!
Minor injury to the operator or third parties can
occur. The tractor, the cabin, or the environment can be damaged.
Comply with the safety instruction.
Note!
Important, helpful tips or information for the operator.
Read this note. It facilitates your work.
Safety
Page 5
Attention!
Injuries can occur due to improper operation. The implement can be dam-
aged.
Read the operating manual all the way through.
Comply with the safety instructions.
Attention!
Injuries due to fluid escaping under high pressure.
Comply with the instructions in the operating manual.
Attention!
Danger of crushing due to moving parts.
Never reach into the crushing hazard danger zone, if parts are still moving
or can move.
Comply with the instruction in the operating manual.
2.4 Special safety instructions
Safety instructions are specified in this section that are also affixed as stickers on the im-
plement.
Attention!
Prior to start-up read and comply with the operating manual and the safety
instructions.
Attention!
Prior to performing maintenance and repair tasks, turn off the engine and re-
move the key.
Installation
Page 6
3 Installation
Attention!
Before starting up the implement, read the instructions on safety and han-
dling for operation of the entire implement and connection to the tractor.
3.1 Preparations on the snow blade
The prerequisite for attaching the snow blade is a tractor with front lift and coupling trian-
gle, as well as two coupling sockets for supplemental hydraulics. The following prepara-
tions must be made for connecting the supplemental hydraulics.
1. Remove the two sealing plugs on the hydraulic cylinder of the snow blade.
2. Screw the two angled branch pieces into the hydraulic cylinder and pay attention to
the position of the angle pieces as shown in Fig 2: Alignment of the angled swivel
threaded unions.
3. Screw the reducers into the quick-connect plugs and then screw in both together on
the hydraulic line as shown in Fig. Fig 3: Connection components - tractor side.
Fig 1: Connection components on the hydraulic cylinder of the snow blade
Angled swivel
threaded union
Installation
Page 7
Fig 2: Alignment of the angled swivel threaded unions
Fig 3: Connection components - tractor side
Reducer
Quick-connect
plugs
Installation
Page 8
3.2 Installation of pressure contol valve
The pressure control valve can be installed as an option. Please mount and connect the
hydraulics as in the following pictures.
Fig 4: Install the valve
Fig 5: Connect hydraulic hoses
Fig 6: Connect hydraulic hoses
1
2
1
2
to the tractor
to the tractor
Installation
Page 9
3.3 Attaching the snow blade on the tractor
In order to attach the snow blade onto a tractor, the tractor must be equipped with a front
lift. Below, take up via a coupling triangle is described in more detail:
1. Position the snow blade in such a manner that you can drive to just in front of its
coupling triangle.
2. Then the coupling triangle of the front lift is lowered all the way and is brought under
the triangle of the snow blade by driving the tractor forward. In this process, ensure
that the coupling triangle of the front lift is tilted slightly forward. If it is not possible to
easily drive forward under the triangle of the snow blade, then the height can be set
suitably by adjusting the attachment flange. To do this you must remove the 6
screws and shift the coupling triangle up or down on the attachment flange. The final
step is to retighten the threaded unions.
Fig. 7: Adjusting the coupling triangle
3. Lifting the front power system hooks its coupling triangle in under coupling triangle of
the snow blade.
4. Then the locking pins on the coupling triangle must be inserted and secured via the
spring cotter pin. If this is not possible then the locking part must be readjusted. To
do this both nuts are unscrewed, the locking part is adjusted, the bolt is inserted and
then it is retightened.
Attachment flange
Threaded union
Installation
Page 10
Fig. 8: Locking pin on the coupling triangle
5. Then the two hydraulic hoses, for the angle adjustment of the snow blade must be
fitted onto the coupling sockets of the supplemental hydraulic system.
Fig. 9: Connecting the hydraulic lines on the tractor hydraulic system
Attention!
Both hydraulic connections must be connected on the cylinder in order to
swing the snow blade to the left as well as to the right.
Locking pins
Spring cotter pin
Nut
Andere Handbücher für SRM-FB 130
1
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Andere matev Traktorzubehör Handbücher
matev
matev FPS-FKH-Kioti CX 2510 Bedienungsanleitung
matev
matev FPS-PTO JD 4020 Montageanleitung
matev
matev SCA-130 Bedienungsanleitung
matev
matev FPS-FKH-NH Boomer 35 MJ 2021 Bedienungsanleitung
matev
matev FPS-FZW-Kioti CS 2520 Bedienungsanleitung
matev
matev SRM-SF 140 Montageanleitung
matev
matev FPS-FKH-Kioti CS 2520 Bedienungsanleitung
matev
matev SRM-VP 130 Montageanleitung
matev
matev FPS JD-2036R Bedienungsanleitung
matev
matev FPS-LS J23/27 Montageanleitung
