Matrix COSEC VEGA CPM MIFARE SMART Bedienungsanleitung

COSEC VEGA CPM MIFARE SMART

TABLE OF CONTENT

IMPORTANT SAFETY INSTRUCTIONS…………………..…Page No.3

GENERAL……………………………………………………………… Page No.4

SPECIFICATION…………………………………………………….. Page No.5

Pin Description………………………………………….…………..Page No.5

INSTALLATION ………………………………………………....…Page No.6

ANTENNA………………………………………………..…………… Page No.8

OPERATION ………………………………………………………… Page No.8

FCC REGISTRATION INFORMATION……………………… Page No.9

IMPORTANT SAFETY INSTRUCTIONS

When using your COSEC CPM MIFARE SMART Reader, basic safety precautions should always be

followed to reduce the risk of fire, electrical shock, and injury to persons. In addition, the following

should also be followed:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use mild

soap.

4. Do not use this product near water, such as bath-tub, wash bowl, kitchen sink, laundry tub, in a wet

basement, or swimming pool.

5. This product should be operated only from the type of power source indicated on the marking label in

the end/host product. If you are not sure of the type of power supplied to your installation site, consult

your dealer or local power company.

6. Never push objects of any kind into this product or through the cabinet slots as they may touch

voltage points or short out parts that could result in fire or electric shock. Never spill liquid of any kind

on the product.

7. To reduce the risk of electric shock, do not disassemble this product by yourself, but take it to

qualified service whenever service or repair is required. Opening or removing the covers may expose

you to dangerous voltages or other risks. Also, incorrect reassembly can cause electric shock when the

unit is subsequently used.

8. Unplug this product from the Direct Current (DC) power source and refer to qualified service

Personnel under these conditions:

a. When the power supply cord or plug is damaged or frayed.

b. If liquid has been spilled on the product.

c. If the product does not operate normally after following the operating instructions in this manual.

Adjust only those controls that are covered by the operating instructions in this manual. Improper

adjustment of other controls that are not covered by this manual may damage the unit and will often

require extensive work by a qualified technician to restore normal operation.

d. If the product exhibits a distinct change in performance.

GENERAL

The MATRIX COSEC CPM MIFARE SMART MODULE is an elegant looking reader which can be mounted to

metal door frame (mullion) or any flat wall surface. MATRIX COSEC CPM MIFARE SMART MODULE

Reader uses an electronic module in epoxy potting that ensures successful operation even in harsh

environments.

The COSEC VEGA CPM MIFARE SMART MODULE design eliminates using external amplifiers, filters,

antenna driver and even micro-controller. Approximately 6K flash memory is free for custom specific

applications.

The reading distance varies according to antenna size. The practical read range is between 2-8

centimeters. Typically read range is 5cm.

SPECIFICATION

Model

COSEC VEGA CPM MIFARE SMART

Write/Read Range

2-8 cm

Power/Current

5 - 5.5VDC (12VDC adapter through host

product)

Working Frequency

13.56 MHz

Operating Temperature

-40 to 85°C

Dimension in mm

71.4 x 43.4

Weight

20 g

Pin Definition

Table 1 shows the general pin attributes of COSEC CPM MIFARE SMART

Symbol

Type

Description

TDO / OUT0

test data output for boundary scan interface / general purpose output 0

TDI / OUT1

I/O

test data input boundary scan interface / general purpose output 1

TMS / OUT2

I/O

test mode select boundary scan interface / general purpose output 2

TCK / OUT3

I/O

test clock boundary scan interface / general purpose output 3

SIGIN /OUT7

I/O

Contactless communication interface output. / general purpose output 7

SIGOUT

Contactless communication interface input.

DVDD

PWR

digital power supply buffer [1]

VDD

PWR

power supply

AVDD

PWR

analog power supply buffer [1]

AUX1

auxiliary outputs: Pin is used for analog test signal

AUX2

auxiliary outputs: Pin is used for analog test signal

RXP

Receiver input pin for the received RF signal.

RXN

Receiver input pin for the received RF signal.

VMID

PWR

internal receiver reference voltage [1]

TX2

transmitter 2: delivers the modulated 13.56 MHz carrier

TVSS

PWR

transmitter ground, supplies the output stage of TX1, TX2

TX1

transmitter 1: delivers the modulated 13.56 MHz carrier

TVDD

PWR

transmitter voltage supply

XTAL1

Crystal oscillator input: Input to the inverting amplifier of the oscillator. This pin

isalso the input for an externally generated clock (fosc = 27.12 MHz)

XTAL2

crystal oscillator output: output of the inverting amplifier of the oscillator

PDOWN

Power Down (RESET)

CLKOUT /

OUT6

clock output / general purpose output 6

SCL

Serial Clock line

SDA

I/O

Serial Data Line

PVDD

PWR

pad power supply

IFSEL0 / OUT4

host interface selection 0 / general purpose output 4

IFSEL1 / OUT5

host interface selection 1 / general purpose output 5

IF0

I/O

interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

IF1

I/O

interface pin, multifunction pin: Can be assigned to host interface SPI, I2C, I2C-L

IF2

I/O

interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

IF3

I/O

interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

Table1. Pin description...continued

Symbol

Type

Description

IRQ

interrupt request: output to signal an interrupt event

VSS

PWR

ground and heat sink connection

[1] This pin is used for connection of a buffer capacitor. Connection of a supply voltage might damage the device

INSTALLATION

Insert the RF reader module “COSEC VEGA CPM MIFARE SMART”, matching the connector pins on the

module with those provided on the card reader slot.

1. Remove the back cover of your device by removing all screws as shown in Figure.

2. Hold the Card Personality Module with the smooth surface towards you, and the narrower end

facing down as shown in Figure.

3. Lower the module in this position into the CPM slot as shown in Fiure.

4. Press the free end of the module inwards with your fingertips to lock it in place as shown in

figure.

5. Replace the back cover as shown in fugure.

ANTENNA

COSEC VEGA CPM MIFARE SMART Antennas are PCB based with different dimensions and having around

2µH +/- 2% µH inductance.

The module supports for different Matrix make antennas, the intentional radiator (COSEC VEGA CPM

MIFARE SMART) may be operated with the antenna with which it is authorized.

Supports following antenna:

OPERATION

Matrix COSEC CPM MIFARE SMART is the wireless non-contact use of radio-frequency electromagnetic

fields, for the purposes of identifying and tracking tags attached to objects.

The reader continuously emits RF carrier signals, and keeps observing the received RF signals for data.

The presence of a tag modulates the RF field, and the same is detected by the reader.

The passive tag absorbs a small portion of the energy emitted by the reader, and starts sending

Modulated information when sufficient energy is acquired from the RF field generated by the reader.

The reader demodulates the signals received from the tag antenna, and decodes the same for further

processing.

This MIFARE SMART reader works with 13.56 MHz tags in credit card size shape cards. When you

approach an RFID Tag close enough (2-8 cm) to the reader's coil, the reader will read the 10-digit unique

ID of the Tag and transmit it as ASCII characters through the serial output with 2400 bits per second.

The circuit in the buzzer in end product/Door controller beeps when a Tag is read successfully.

Matrix COSEC MIFARE SMART Module support 13.56MHz Frequency.

FCC REGISTRATION INFORMATION

2.2 list of applicable FCC rules

This device complies with part 15.225 of the FCC rules.

2.3 Summarize the specific operation use conditions

This module can be used in household electrical appliances as well as lighting equipment’s.

The input voltage to the module should be nominally 5.0 to 5.5V d.c.,

The ambient temperature of the module should not exceed 80˚C.

The antenna is not field replaceable. If the antenna needs to be change, the certification should be re-

applied.

2.4 Limited module procedures

This module doesn't have shielding cover, which belongs to a Limited module and is applied to

a fixed host; the name of the host is COSEC VEGA. Please refer to the INSTALLATION chapter

(Page No.6 and 7) for details.

2.5 Trace Antenna

Not applicable

2.6 RF exposure consideration

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 5cm between the radiator &

your body.

2.7 Antenna

Module only contains one PCB antenna. No additional external connectors.

2.8 Label and compliance information

FCC on the final system must be labeled with “Contains FCC ID: 2ADHNCOSEC02”.

2.10 Addition testing, Part 15 subpart B disclaimer

The final host/module combination need to be evaluated against the FCC Part 15B criteria for

unintentional radiators in order to be properly authorized for operation as a Part 15 digital device

The host integrator installing this module into their product must ensure that the final composite

product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules,

including the transmitter operation and should refer to guidance in KDB 996369.

Frequencyspectrumtobeinvestigated

For host products with certified modular transmitter, the frequency range of investigation of the

composite system is specified by rule in Sections 15.33(a)(1) through (a)(3), or the range applicable to

the digital device, as shown in Section 15.33(b)(1), whichever is the higher frequency range of

investigation.

To OEM Installer:

1. FCC on the final system must be labeled with “Contains FCC ID: 2ADHNCOSEC02”.

2. In the user manual, final system integrator must ensure that there is instruction provided in the user

Manual to install or remove the transmitter module.

3. Transmitter module must be installed used in strict accordance with the Manufacturer’s instructions

as described in the user documentation that comes with the product.

The user manual of the final host system must contain the following statements:

This device complies with Part 15 of the FCC rules. Operation is subject to following

Two conditions: 1. this device may not cause harmful interference and

2. This device must accept any interference received including interference that may cause undesired

operation of this device.

The changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

Inhaltsverzeichnis

Andere Matrix Kartenleser Handbücher

Matrix

Matrix COSEC CPM EM PROX Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch