matson BT400 Bedienungsanleitung
DIGITAL BATTERY
TESTER
MANUAL
BT400
OWNER’S MANUAL
Read Entire Manual Before Using This Product
Battery/Charging/Starting System Analyser / Printer
DIGITAL BATTERY TESTER
BT4002 |
TEST PROCEDURES / OPERATING
INSTRUCTIONS
IMPORTANT
WARNING: This product can expose you to chemicals including
arsenic, which is known to the State of California to cause cancer.
1. For testing 12 volt batteries, and for testing 12 and 24 volt charging systems.
2. Suggested operation range 0ºC (32ºF) to 50ºC (122ºF) in ambient temperature.
1. Working in the vicinity of a lead acid battery is dangerous. Batteries generate
explosive gases during normal battery operation. For this reason, it is of utmost
importance, if you have any doubt, that each time before using your tester, you read
these instructions very carefully.
2. To reduce risk of battery explosion, follow these instructions and those published by
the battery manufacturer and manufacturer of any equipment you intend to use in
the vicinity of the battery. Observe cautionary markings on these items.
3. DO NOT expose the tester to rain or snow.
For more information, go to www.P65Warnings.ca.gov.
DIGITAL BATTERY TESTER
| 3BT400
PERSONAL SAFETY PRECAUTIONS
PREPARING TO TEST
1. Someone should be within range of your voice or close enough to come to your aid
when you work near a lead acid battery.
2. Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing or eyes.
3. Wear safety glasses and protective clothing.
4. If battery acid contacts skin or clothing, wash immediately with soap and water.
If acid enters eye, immediately ood eye with running cold water for at least ten
minutes and get medical attention immediately.
5. NEVER smoke or allow a spark or ame in vicinity of battery or engine.
6. Be extra cautious to reduce risk of dropping a metal tool onto the battery.
It could spark or short-circuit the battery or other electrical parts and could
cause an explosion.
7. Remove personal metal items such as rings, bracelets, necklaces and watches when
working with a lead acid battery. It can produce a short circuit current high enough
to weld a ring or the like to metal causing a severe burn.
1. Be sure area around battery is well ventilated while battery is being tested.
2. Clean battery terminals. Be careful to keep corrosion from coming in contact
with eyes.
3. Inspect the battery for cracked or broken case or cover. If battery is damaged,
do not use tester.
4. If the battery is not sealed maintenance free, add distilled water in each cell
until battery acid reaches level specied by the manufacturer.This helps purge
excessive gas from cells. Do not overll.
5. If necessary to remove battery from vehicle to test, always remove ground
terminal from battery rst. Make sure all accessories in the vehicle are o to
ensure you do not cause any arcing.
DIGITAL BATTERY TESTER
BT4004 |
OPERATION & USE
Note: Each time you connect the tester to a battery, the tester will run a quick cable
verication to ensure a proper connection through the output cables to sensors in the
clamp jaws. If the connection checks out OK, the tester will proceed to the Home Screen.
If the connection is poor, the display will show“CHECK CABLE”. In this case, check cable
connections for visible signs of damage, as you may need to re-connect the clamps to
the battery or replace the cable end.
1. Before you test a battery in a vehicle, turn o the ignition, all accessories and loads.
Close all the vehicle doors and the trunk lid.
2. Make sure the battery terminals are clean. Wire brush them if necessary. Clamp the
black load lead to the vehicle negative battery terminal. Clamp the red load lead to
the vehicle positive battery terminal. Please clamp on the lead part of the terminal
only. Clamping on the iron part of the terminal will lead to wrong test results.
BEFORE TESTING
MAIN MENU
SYSTEM ANALYSER You will view the following screens by pressing
/ to switch between all functions and settings.
BATTERY TEST
XX.XX V Press «ENTER» to do battery test.
SYSTEM TEST
XX.XX V Press «ENTER» to do system test.
IN-VEHICLE TEST
XX.XX V Press «ENTER» to do In-vehicle test.
LANGUAGE SELECT Press «ENTER» to change language.
BRIGHTNESS Press «ENTER» to start adjusting brightness
of the screen.
DIGITAL BATTERY TESTER
| 5BT400
BATTERY TEST
1. Select BATTERY TEST. Press «ENTER».
BATTERY TEST
XX.XX V
2. Press the / to select REGULAR/STD or START/STOP battery.
REGULAR/STD START/STOP
REGULAR/STD BATTERY:
FLOODED, AGM FLAT PLATE,
AGM SPIRAL, VRLA/GEL
START/STOP BATTERY:
AGM FLAT PLATE, EFB
3. Press the / key to select the battery type:
BATTERY TYPE:
AGM FLAT PLATE
ENTER
4. Press «ENTER» to conrm choice.
5. Press the / key to select the battery rating: CCA/SAE, EN, JIS, DIN, IEC, & CA/MCA.
SELECT RATING:
CCA/SAE
DIGITAL BATTERY TESTER
BT4006 |
7. Press the / key to input the battery capacity.
CCA/SAE: 40~2000
EN: 40~1885
DIN: 25~1120
IEC: 30~1320
JIS: By Battery Type No.
CA/MCA: 50~2400
BATTERY TEST
SELECT CAPACITY:
560CCA/SAE
ABOVE 32°F/0°C?
YES/NO
8. Press the / key to conrm temperature.
9. Press <<Enter>> to begin the test.
*Return Feature: Before the test is started, the user can always return to the previous
setting page by pressing <<ENTER>> for 2 seconds.
SURFACE CHARGE NOTICE:
The battery will hold a surface charge if the engine has been running or after the
battery has been charged.The tester may prompt you to remove the surface charge.
6. Press «ENTER» to conrm choice.
ENTER
DIGITAL BATTERY TESTER
| 7BT400
BATTERY TEST
A. Follow the instructions indicating when to turn the headlights on and o or apply a
load into the battery.
In Vehicle:
Out Of Vehicle:
SURFACE CHARGE IN VEHICLE?
YES
SURFACE CHARGE IN VEHICLE?
NO
TURN HEADLIGHTS ON FOR 15 SECS
TESTING
TESTING
IS BATTERY CHARGED?
YES/NO
B. The tester will resume testing after it detects that the surface charge is removed.
10. Test the battery for few seconds.
11. Press the / key to select battery fully charged or not if tester asks.
Press «ENTER» to conrm choice.
12. When the test is completed, the display shows the actual volts and the actual
CCA and internal resistance. {Press the / key to read: SOH (STATE OF HEALTH)
and SOC (STATE OF CHARGE)}.
DIGITAL BATTERY TESTER
BT4008 |
BATTERY TEST
13. One of the six test results will be displayed:
GOOD & PASS
VOL: xx.xx V
CCA: xxxx CCA/SAE
IR: xx.xx mΩ
CAUTION
VOL: xx.xx V
CCA: xxxx CCA/SAE
IR: xx.xx mΩ
BAD & REPLACE
VOL: xx.xx V
CCA: xxxx CCA/SAE
IR: xx.xx mΩ
BAD CELL & REPLACE
VOL: xx.xx V
CCA: xxxx CCA/SAE
IR: xx.xx mΩ
RECHARGE & RETEST
VOL: xx.xx V
CCA: xxxx CCA/SAE
IR: xx.xx mΩ
GOOD & RECHARGE
VOL: xx.xx V
CCA: xxxx CCA/SAE
IR: xx.xx mΩ
GOOD & PASS
*The battery is good and capable of
holding a charge.
GOOD & RECHARGE
*The battery is good but needs to
be recharged.
CAUTION
*The battery may be serviced but
decrease the capability of starting the
engine gradually. The battery may fail
under extreme climate conditions. There
may be a poor connection between the
vehicle and the battery aecting the
charging function. Please pay attention to
the battery for replacement consideration
and charging system checking.
RECHARGE & RETEST
*Battery is discharged, the battery
condition cannot be determined until
it is fully charged. Recharge & retest
the battery.
BAD & REPLACE
*The battery will not hold a charge.
It should be replaced immediately.
BAD CELL & REPLACE
*The battery has at least one cell short
circuit. It should be replaced immediately.
DIGITAL BATTERY TESTER
| 9BT400
BATTERY TEST
LOAD ERROR
GOOD & PASS
SOC: xx.xx V
90%
GOOD & PASS
SOH: xxxx CCA/SAE
90%
LOAD ERROR
*The tested battery is bigger than 2000CCA/SAE or 200AH. Or the clamps are not
connected properly. Please fully charge the battery and retest after excluding both
previous reasons. If reading is the same, the battery should be replaced immediately.
14. SOC & SOH Display: Press directional keys to see SOC & SOH:
15. Press «ENTER» return to MAIN MENU or remove the test clamps from the
battery posts after completion of testing batteries to end test.
ENTER
DIGITAL BATTERY TESTER
BT40010 |
SYSTEM TEST
1. Select “SYSTEM TEST”from the main menu.
2. Turn o all vehicle accessory loads such as light, air conditioning, radio, etc.
Before starting the engine.
3. When the engine is started, one of the three results will be displayed along
with the actual reading measured.
SYSTEM TEST
xx.xx V
PRESS ENTER FOR CHARGING TEST MAKE SURE ALL LOADS ARE OFF
TURN OFF LOADS
START ENGINE
CRANKING VOLTS
xx.xx V NORMAL
CRANKING VOLTS
xx.xx V LOW
CRANKING VOLTS
NOT DETECTED
CRANKING VOLTS NORMAL
The system is showing normal draw.
Press «ENTER» to perform the charging
system test.
CRANKING VOLTS LOW
The cranking voltage is below normal
limits, troubleshoot the starter with
manufacturers recommended procedure.
CRANKING VOLTS NOT DETECTED
The cranking voltage is not detected.
4. Press «ENTER» to begin charging system test.
Inhaltsverzeichnis
Andere matson Prüfgeräte Handbücher
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung