Mattel Vidster Bedienungsanleitung

Keep these instructions for future reference as they contain important information.

• For use with the Vidster™

• Requires 4 AA Alkaline batteries (not included).

Age: 8+

FCC STATEMENT:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Mattel Inc.

333 Continental Blvd.

El Segundo, CA

(310) 252-2000

NOTE: Changes or modiﬁ cations not expressively approved by the manufacturer responsible for compliance could void the user’s authority to

operate the equipment.

TABLE OF CONTENTS

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Battery Installation

Installing the Hand grip or (optional) Tripod

Installing SD Memory Card (Optional)

Installing Microphone (Optional)

Using the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Camera Controls

Taking a Picture

Video Recording

Zoom In/Zoom Out

Adjust Volume

Playback Mode

Connecting to your TV

Downloading From Your Vidster™

Features & Speciﬁcations . . . . . . . . . . . . . . . . . . . . 14

Tips & Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 15

PACKAGE CONTENTS

The following is included with every Mattel Vidster™:

1 Handheld Vidster™

unit with Hand Strap

1 A/V cable

1 Hand Grip

1 Instructions

QUICK START

Ready to start taking pictures

or making videos? In just a few steps,

you’ll be ready to go.

1. Install 4 AA Alkaline

batteries & remove

the clear protective

ﬁlm from the viewing screen.

2. Switch the camera to “On”.

3. Set the Mode switch to “Picture” to take a digital photo, or

“Video” to record a video.

4. Press the Center button to take a picture in Picture Mode or

start recording in Video Mode.

5. Press the Center button a second time to stop recording in

Video Mode.

Battery Installation/Replacement

The Vidster™ uses 4 AA Alkaline batteries to

power it. Make sure the unit is off. Locate the

battery cover on the underside of the device.

(1)Use a Phillips screwdriver (not included) to

loosen both screws. (2)Remove battery

cover. (3)Insert four fresh “AA” alkaline

batteries in the orientation shown. (4)Replace

the cover and tighten both screws.

For longer life, use only alkaline batteries.

Battery Safety Information

In exceptional circumstances batteries may leak ﬂuids that can

cause a chemical burn injury or ruin your product. To avoid

battery leakage:

• Do not recharge non-rechargeable batteries.

• Remove rechargeable batteries from the product before

being charged (if designed to be rechargable).

• Charge rechargeable batteries only under adult supervision

(if designed to be rechargable).

• Do not mix alkaline, standard (carbon-zinc) or rechargeable

(nickel-cadmium) batteries.

• Do not mix old and new batteries.

• Use only batteries of the same or equivalent type

as recommended.

• Insert batteries with the correct polarity.

• Remove exhausted batteries from the product.

• Do not short-circuit the supply terminals.

• Dispose of batteries safely.

• Do not dispose of this product in a ﬁre. The batteries inside

may explode or leak.

2 3

Battery Cover

Using the camera

Use the handgrip or the hand strap to

keep a proper hold on your camera.

A tripod (optional) can also be purchased so that your camera can be

set in one position for longer shoots or self-portraits.

To install your Grip

or Tripod:

(1) Locate the threaded

insert on the bottom

of the Vidster™.

(2) Align and insert the

threads on the grip

(included) or a Tri-pod

(optional) with the

camera insert.

(3) Tighten the thumb-

screw ﬁnger tight

(do not use any tools

to tighten this screw,

as it may cause

damage to your camera

or accessory).

4 5

Right.

Wrong.

Installing SD Memory Card (Optional)

Your Vidster™ comes complete with 32MB of memory for saving

pictures or video. If you want more memory, you’ll need to add an SD or

MMC Memory Card (sold separately) with a memory size greater than

32MB. This external memory takes priority over any internal memory.

Turn –off your Vidster before installing a memory card.

To insert an SD Memory Card, (1) locate and

open the memory door marked with the icon

on the bottom of the Vidster™.

(2) Make sure the SD Memory Card is

properly oriented. (3) Then push the card

into the slot until it ﬁts snugly inside.

(4) The memory door may then be closed.

The Vidster™ will automatically recognize

when the SD Memory Card has been

properly installed.

Note: You should never remove the Memory Card while the camera is in

operation.

Installing Microphone (Optional)

The Vidster™ system has its own

internal microphone but it can

also be used with an external

microphone (not included). To use

an external mic, simply insert the

microphone’s connector into the

Microphone Input Jack found in the

front of the Vidster™. The Vidster™

will automatically start using the

external microphone.

USING YOUR VIDSTER

Camera Controls

To turn the camera on, ﬁnd the

Power ON/OFF switch on the

side of the Vidster™. Push the

switch to the ON position.

There may be a slight delay before

the screen comes to life.

6 7

Speaker

Power

On/Off A/V Out Mini-USB

Port

Imager

Microphone

Jack

Video

LED

Internal

Microphone

Here’s a list of what the buttons on the Control Pad do:

Direction Pad (D-Pad) Function

Up Zoom In; Scroll Up, Volume Up

Down Zoom Out; Scroll Down, Volume Down

Left Delete (playback only)

Right Volume Control (playback only)

Center Start / Stop Recording; Select Option

Taking a Picture

To take a picture using the Vidster™:

1. Switch the camera ON.

2. Set the Mode switch to PICTURE.

A camera icon will appear on the screen.

3. Set the Zoom (see Zoom In / Zoom Out

section for details).

4. Press the Center button to take the picture

Your picture is then displayed for you to

review. If you want to delete the current

picture, press the Delete (left) button on the

D-Pad. This brings up the Delete menu. Select YES or NO and press the

Center button to conﬁrm your choice. Otherwise, in just a few seconds,

the photo will be saved to the archive.

Video Recording

To record a video using the Vidster™:

1. Switch the camera ON.

2. Set the Mode switch to VIDEO. A video camera icon will

appear on the screen.

3. If the memory is full you will get an on-screen message saying

“Memory Full,” you need to delete video or add an empty SD Card.

4. Set the Zoom (see Zoom In / Zoom Out section for details).

8 9

Right

Down

Center

Left

Mode

switch

5. Press the Center button to start recording. A video time counter will

appear on the screen showing the length of time of this recording.

6. Press the Center button to stop recording when you’re done.

When you are recording a video the red LED light on the front of Vidster‘

will come on.

Zoom In / Zoom Out

If you want your view to move in closer or out farther, press the Up

button or Down button to zoom. The zoom has three settings 1x, 1.5x

and 2x.

* The Zoom level cannot be changed while video is being recorded.

Adjust Volume

During playback mode, you can set the speaker volume in order to

listen to recorded videos. To do so, press the Right button on the D-Pad

to get to the volume control. Press the Up button (Volume Up) on your

D-Pad or the Down button (Volume Down). The volume level will be

immediately displayed on your LCD. You may increase or decrease the

volume in increments of 1; there are 7 volume levels total.

Camera Playback

Switch the Mode button to playback. It will default to the last

mode- video if you just shot a video, photo if you just shot a photo- and

press the Down button if you want to view a Photo. Press the Center

button to conﬁrm your choice. Scroll forward using the Top button or

backwards by using the Bottom button. At any time you may choose to

delete a photo by pressing the Delete (left) button on the D-Pad. This

brings up the Delete menu. Select YES or NO and press the Center

button to conﬁrm your choice.

At either end of your archived photos, you will return to the playback

mode menu. In this menu, you can use the Up button to navigate to the

Video mode or it will default to the Photo playback. Pressing the Center

button will conﬁrm your selection. While viewing your photos you may

press the Center button to see a full screen image of the picture.

Camera Slideshow Playback

To start the slideshow, select any photo by pressing the Center button

(photo enlarge to ﬁll the full screen). Then select it a second time. Each

photo will be shown for about three seconds until moving to the next

10 11

picture on the list. At the completion, it will return to the archived

photos. At anytime you may press the Center button to exit the

slideshow and return to the Camera Playback menu.

Video Camera Playback

Scroll forward (top button) or backwards (bottom button) to see the

opening scene of all the videos archived. At any time you may choose

to delete a video by pressing the Delete (left) button on the D-Pad. This

brings up the Delete menu. Select YES or NO and press the Center but-

ton to conﬁrm your choice.

At either end of your archived videos, you will return to the playback

mode menu. In this menu, you can use the down buttons to navigate to

the photo playback or default to the video playback. Pressing the Center

button will conﬁrm your selection.

Navigate to any opening video scene and press the Center button to

view the video. At its completion, you will be returned to the video ar-

chives or you may stop a video at any time and be returned to the video

archives.

Note: If there are no pictures or scenes in the archive, use the up button to return to the

main menu.

Connecting to your TV

Whether playing a scene back from the archive or showing your friends

what you’re doing in real time, you can hook your Vidster™ to most TV.

1. With both your Vidster™ and your TV in

the off position. Locate the A/V out plug on

your Vidster™.

2. Attach your A/V cable (included) from the

Vidster™ to your television video in. Plug the

single plug into the side of your Vidster™ and

connect the other end containing two plugs into your TV video in,

matching the red plug to the TV’s audio input and the

yellow plug to the video input.

3. Turn on the Television and select the appropriate input (you may need

to consult your Television’s manual). Turn on your Vidster™.

4. Your Vidster™ screen will be blank, as the TV now becomes your

viewing screen. Operate your Vidster™ normally. Any image on your

Vidster™ will now be seen on your TV.

Downloading From Your Vidster™

If you want to download any of your images from your Vidster™;

1. Turn off your Vidster™ attaching a mini-USB cable (sold separately)

to a compatible computer and your Vidster™.

12 13

2. Set the slide switch to Playback mode and turn on your Vidster™.

Your Vidster™ cannot be used as a camera or a video camera while

it’s attached to your computer. The Vidster™ will show up as a

‘removable drive’ on your computer once it’s plugged in. You can then

move the images off and/or delete them, just as you would from any

other storage drive.

3. Before removing or turning off your Vidster‘ camera, follow your

computer’s standard procedure for stopping & removing USB mass

storage device. Then turn–off your Vidster and disconnect it from

your computer.

Recommended minimum system conﬁguration

• 550 MHZ Pentium III, AMD K-6, or equivalent processor with

MMX support

• 128MB RAM or more

• 16MB video RAM or more

• Microsoft DirectX 9.0 installed

• 7200 RPM or faster hard disk

• Operating System: Windows ME, Windows 2000, Windows XP

VIDSTER‘ FEATURES & SPECIFICATIONS

Features

• 2x Digital Zoom Vidster™

• 32MB Memory

• Expandable memory via SD/MMC card

• Composite Video Out

• MJPEG video format

• QVGA Video resolution

Speciﬁcations

• SD/MMC card support up to 512MB

• DCIM nomenclature for picture directory

• Automatically detects video cables

• Quality: For Scene mode QVGA (320x240) video at 15 FPS

• MJPEG format

• 1.3 Megapixel photo resolution

• Screen: Internal LCD or TV selected via hardware. If nothing is

plugged into the A/V out connection, all screen data is channeled to

the LCD. If something is plugged into the A/V out connection, all data is

sent in NTSC format.

TIPS & TROUBLESHOOTING

Tips for the New User

Try and keep whatever

you’re shooting well lit

from the front. And always

have adequate light!

14 15

Keep the camera level and steady; even when you’re shooting a video,

move slowly and steadily.

Keep your subject in the ‘X’, to get the best shot.

Try and tell a story with your pictures! For example, if you’re at a

birthday party, get a picture of the cake.

Always turn off your Vidster™ after each use. Remove batteries for

extended storage. Your Vidster™ screen will say “Goodbye” when

powering down. Your Vidster™ will go to sleep automatically after

approximately 2 minutes of no operation. It maybe restarted by

pressing the Center button.

TROUBLESHOOTING

Problem Resolution

“Batteries Low” Batteries low: If you see this, it will soon be

Appears on screen time to replace the batteries.

“Memory Full” When you see this, the Vidster™ memory

Appears on screen is full. Please delete or download any

images or scenes you no longer wish

to keep.

Unit won’t turn on If the Record (center) button hasn’t been

pressed for a while, the LCD will turn off.

Pressing the record button will turn it back

on. If that doesn’t work, try turning the

power switch off and then on again. If the

problem persists, change the batteries.

16 17

Right Wrong

Inhaltsverzeichnis

Andere Mattel Camcorder Handbücher

Mattel

Mattel VIDEO JOURNAL L7280 Bedienungsanleitung

Beliebte Camcorder Handbücher anderer Marken

Toshiba

Toshiba CAMILEO Z100 Bedienungsanleitung

Panasonic

Panasonic NV-VS40B Bedienungsanleitung

Canon

Canon RC 260 Bedienungsanleitung

Sony

Sony Handycam DCR-DVD7E Bedienungsanleitung

Brinno

Brinno TimeLapse TLC200 Bedienungsanleitung

JVC

JVC GR-SXM68AC Kurzanleitung

Panasonic

Panasonic AG-HMC152EN Bedienungsanleitung

MYDLINK

MYDLINK DCS-6100LH Bedienungsanleitung

Sony

Sony video Hi8 Handycam CCD-TR555 Bedienungsanleitung

SECURECOM

SECURECOM V-5014B Bedienungsanleitung

Sharper Image

Sharper Image U-VIDEO Bedienungsanleitung

JVC

JVC AA-V15EG Bedienungsanleitung

Canon

Canon LEGRIA HV40 Bedienungsanleitung

Sony

Sony Handycam DCR-VX2000 Bedienungsanleitung

RCA

RCA CC616 Bedienungsanleitung

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung

Panasonic

Panasonic NVM40 Bedienungsanleitung

ATIK Cameras

ATIK Cameras Horizon Bedienungsanleitung