Maxon motor EPOS2 70/10 Bedienungsanleitung

maxon motor ag Brünigstrasse 220 P.O.Box 263 CH-6072 Sachseln Phone +41 41 666 15 00 Fax +41 41 666 16 50 www.maxonmotor.com

Edition May 2016

EPOS2 Positioning Controller

Getting Started

maxon motor control

Positioning Controller

Getting Started

Document ID: rel5892

maxon motor control

A-2 Document ID: rel5892 EPOS2 Positioning Controller

Edition: May 2016 EPOS2 70/10 Getting Started

PLEASE READ THIS FIRST

These instructions are intended for qualified technical personnel. Prior commencing with any

activities …

• you must carefully read and understand this manual and

• you must follow the instructions given therein.

We have tried to provide you with all information necessary to install and commission the equipment in a

secure, safe and time-saving manner. Our main focus is …

• to familiarize you with all relevant technical aspects,

• to let you know the easiest way of doing,

• to alert you of any possibly dangerous situation you might encounter or that you might cause if

you do not follow the description,

•towrite as little and to say as much as possible and

• not to bore you with things you already know.

Likewise, we tried to skip repetitive information! Thus, you will find things mentioned just once. If, for

example, an earlier mentioned action fits other occasions you then will be directed to that text passage

with a respective reference.

Follow any stated reference – observe respective information – then go back and continue with

the task!

PREREQUISITES FOR PERMISSION TO COMMENCE INSTALLATION

The EPOS2 70/10 is considered as partly completed machinery according to EU directive 2006/42/EC,

Article 2, Clause (g) and therefore is intended to be incorporated into or assembled with other

machinery or other partly completed machinery or equipment.

You must not put the device into service, …

• unless you have made completely sure that the other machinery – the surrounding system the device

is intended to be incorporated to – fully complies with the requirements stated in EU directive 2006/

42/EC!

• unless the surrounding system fulfills all relevant health and safety aspects!

• unless all respective interfaces have been established and fulfill the stated requirements!

maxon motor control

EPOS2 Positioning Controller Document ID: rel5892 A-3

EPOS2 70/10 Getting Started Edition: May 2016

1 About this Document 5

2 Introduction 9

2.1 Documentation Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Installation and Configuration 11

3.1 Important Notice: Prerequisites for Permission to commence Installation. . . 11

3.2 Step 1: Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2.1 Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.3 Step 2: Minimum External Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.3.1 Minimum Wiring for maxon EC motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.3.2 Minimum Wiring for maxon DC motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4 Step 3: System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.4.1 General initial Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.4.2 Configuration of EC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.4.3 Configuration of DC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.4.4 General closing Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.5 Step 4: Regulation Gains Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.5.1 Starting Regulation Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.5.2 Auto Tuning the Current, Velocity and Position Regulators. . . . . . . . . . . . . . . . . . . . . . 24

TABLE OF CONTENTS

maxon motor control

A-4 Document ID: rel5892 EPOS2 Positioning Controller

Edition: May 2016 EPOS2 70/10 Getting Started

••page intentionally left blank••

maxon motor control

EPOS2 Positioning Controller Document ID: rel5892 1-5

EPOS2 70/10 Getting Started Edition: May 2016

1 About this Document

1.1 Intended Purpose

The purpose of the present document is to familiarize you with the described equipment and the tasks

on safe and adequate installation and/or commissioning.

Observing the described instructions in this document will help you …

• to avoid dangerous situations,

• to keep installation and/or commissioning time at a minimum and

• to increase reliability and service life of the described equipment.

Use for other and/or additional purposes is not permitted. maxon motor, the manufacturer of the equip-

ment described, does not assume any liability for loss or damage that may arise from any other and/or

additional use than the intended purpose.

1.2 Target Audience

This document is meant for trained and skilled personnel working with the equipment described. It con-

veys information on how to understand and fulfill the respective work and duties.

This document is a reference book. It does require particular knowledge and expertise specific to the

equipment described.

1.3 How to use

Take note of the following notations and codes which will be used throughout the document.

Table 1-1 Notations used in this Document

Notation Explanation

«Abcd» indicating a title or a name (such as of document, product, mode, etc.)

¤Abcd¤ indicating an action to be performed using a software control element

(such as folder, menu, drop-down menu, button, check box, etc.) or a

hardware element (such as switch, DIP switch, etc.)

(n) referring to an item (such as order number, list item, etc.)

denotes “see”, “see also”, “take note of” or “go to”

maxon motor control

1-6 Document ID: rel5892 EPOS2 Positioning Controller

Edition: May 2016 EPOS2 70/10 Getting Started

1.4 Symbols and Signs

In the course of the present document, the following symbols and sings will be used.

Table 1-2 Symbols & Signs

Type Symbol Meaning

Safety Alert

(typical)

DANGER Indicates an imminent hazardous situation. If not

avoided, it will result in death or serious injury.

WARNING Indicates a potential hazardous situation. If not

avoided, it can result in death or serious injury.

CAUTION Indicates a probable hazardous situation or calls

the attention to unsafe practices. If not avoided, it

may result in injury.

Prohibited

Action (typical)

Indicates a dangerous action. Hence, you must not!

Mandatory

Action (typical)

Indicates a mandatory action. Hence, you must!

Information

Requirement /

Note / Remark

Indicates an activity you must perform prior

continuing, or gives information on a particular item

you need to observe.

Best Practice Indicates an advice or recommendation on the

easiest and best way to further proceed.

Material

Damage Indicates information particular to possible damage

of the equipment.

maxon motor control

EPOS2 Positioning Controller Document ID: rel5892 1-7

EPOS2 70/10 Getting Started Edition: May 2016

1.5 Trademarks and Brand Names

For easier legibility, registered brand names are listed below and will not be further tagged with their

respective trademark. It must be understood that the brands (the below list is not necessarily conclud-

ing) are protected by copyright and/or other intellectual property rights even if their legal trademarks are

omitted in the later course of this document.

Table 1-3 Brand Names and Trademark Owners

1.6 Copyright

The present document – including all parts thereof – is protected by copyright. Any use (including repro-

duction, translation, microfilming and other means of electronic data processing) beyond the narrow

restrictions of the copyright law without the prior approval of maxon motor ag, is not permitted and sub-

ject to persecution under the applicable law.

maxon motor ag

Brünigstrasse 220

P.O.Box 263

CH-6072 Sachseln

Switzerland

Phone +41 41 666 15 00

Fax +41 41 666 16 50

www.maxonmotor.com

Brand Name Trademark Owner

Adobe® Reader® © Adobe Systems Incorporated, USA-San Jose, CA

CANopen®

CiA® © CiA CAN in Automation e.V, DE-Nuremberg

Internet Explorer® © Microsoft Corporation, USA-Redmond, WA

Pentium® © Intel Corporation, USA-Santa Clara, CA

Windows Vista®

Windows® © Microsoft Corporation, USA-Redmond, WA

maxon motor control

1-8 Document ID: rel5892 EPOS2 Positioning Controller

Edition: May 2016 EPOS2 70/10 Getting Started

••page intentionally left blank••

maxon motor control

EPOS2 Positioning Controller Document ID: rel5892 2-9

EPOS2 70/10 Getting Started Edition: May 2016

2Introduction

The present document provides you with information on the first steps using EPOS2 70/10 Positioning

Controller. It describes the standard procedure when putting the device into operation and is meant to

facilitate installation and configuration of a basic EPOS2 70/10 system.

maxon motor control’s EPOS2 70/10 is a small-sized, full digital smart motion control unit. Due to its

flexible and high efficient power stage, the EPOS2 70/10 drives brushed DC motors with digital encoder

as well as brushless EC motors with digital Hall sensors and encoder.

The sinusoidal current commutation by space vector control offers to drive brushless EC motors with

minimal torque ripple and low noise. The integrated position, velocity and current control functionality

allows sophisticated positioning applications. The EPOS2 70/10 is specially designed being com-

manded and controlled as a slave node in a CANopen network. In addition, the unit can be operated via

any USB or RS232 interface.

Find the latest edition of the present document, as well as additional documentation and software to the

EPOS2 70/10 Positioning Controller also on the Internet: www.maxonmotor.com

2.1 Documentation Structure

The present document is part of a documentation set. Please find below an overview on the documenta-

tion hierarchy and the interrelationship of its individual parts:

Figure 2-1 Documentation Structure

maxon motor control

2-10 Document ID: rel5892 EPOS2 Positioning Controller

Edition: May 2016 EPOS2 70/10 Getting Started

2.2 Safety Precautions

Prior continuing …

• make sure you have read and understood chapter “ PLEASE READ THIS FIRST” on page A-2,

• do not engage with any work unless you possess the stated skills (chapter “1.2 Target Audi-

ence” on page 1-5),

• refer to chapter “1.4 Symbols and Signs” on page 1-6 to understand the subsequently used indi-

cators,

• you must observe any regulation applicable in the country and/or at the site of implementation

with regard to health and safety/accident prevention and/or environmental protection,

• take note of the subsequently used indicators and follow them at all times.

Requirements

• Make sure that all associated devices and components are installed according to local regulations.

• Be aware that, by principle, an electronic apparatus can not be considered fail-safe. Therefore, you

must make sure that any machine/apparatus has been fitted with independent monitoring and safety

equipment. If the machine/apparatus should break down, if it is operated incorrectly, if the control unit

breaks down or if the cables break or get disconnected, etc., the complete drive system must return –

and be kept – in a safe operating mode.

• Be aware that you are not entitled to perform any repair on components supplied by maxon motor.

Best Practice

• For initial operation, make sure that the motor is free running. If not the case, mechanically discon-

nect the motor from the load.

Maximal permitted Supply Voltage

• Make sure that supply power is between 11…70 VDC.

• Supply voltages above 75 VDC will destroy the unit.

• Wrong polarity will destroy the unit.

Electrostatic Sensitive Device (ESD)

• Make sure to wear working cloth in compliance with ESD.

• Handle device with extra care.

DANGER

High Voltage and/or Electrical Shock

Touching live wires causes death or serious injuries!

• Consider any power cable as connected to live power, unless having proven the opposite!

• Make sure that neither end of cable is connected to live power!

• Make sure that power source cannot be engaged while work is in process!

• Obey lock-out/tag-out procedures!

• Make sure to securely lock any power engaging equipment against unintentional engagement and

tag with your name!

Andere Handbücher für EPOS2 70/10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere maxon motor Controller Handbücher

maxon motor

maxon motor ESCON Module 50/5 Anwendungshandbuch

maxon motor

maxon motor EPOS 24/1 Bedienungsanleitung

maxon motor

maxon motor EPOS4 50/5 Anwendungshandbuch

maxon motor

maxon motor 24/2 Bedienungsanleitung

maxon motor

maxon motor EPOS2 P 24/5 Anwendungshandbuch

maxon motor

maxon motor EPOS 70/10 Anwendungshandbuch

maxon motor

maxon motor EPOS2 70/10 Anwendungshandbuch

maxon motor

maxon motor EPOS2 Module 36/2 Anwendungshandbuch

maxon motor

maxon motor EPOS4 Module 50/8 Anwendungshandbuch

maxon motor

maxon motor ESCON Module 50/4 EC-S Anwendungshandbuch

maxon motor

maxon motor 4-Q-EC Bedienungsanleitung

maxon motor

maxon motor EPOS 24/1 Anwendungshandbuch

maxon motor

maxon motor ESCON 36/3 EC Anwendungshandbuch

maxon motor

maxon motor EPOS4 Module 24/1.5 Anwendungshandbuch

maxon motor

maxon motor ESCON 50/5 Anwendungshandbuch

maxon motor

maxon motor EPOS4 50/5 Anwendungshandbuch

maxon motor

maxon motor ESCON 70/10 Anwendungshandbuch

maxon motor

maxon motor EPOS 24/5 Bedienungsanleitung

maxon motor

maxon motor EPOS2 24/5 Anwendungshandbuch

maxon motor

maxon motor EPOS4 Module 50/8 Anwendungshandbuch

maxon motor

maxon motor EPOS2 24/2 Anwendungshandbuch

maxon motor

maxon motor EPOS2 Module 36/2 Anwendungshandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

maxon motor EPOS2 70/10 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken