MAXSA Solar 40227 Kurzanleitung
Your MAXSA Solar Security Light converts sunlight into electricity during the
day, enabling the 80 LED lights to turn on automatically at night when motion is
detected. With this light, walking into the dark will no longer be a problem. You
can also save the environment by conserving energy with these energy-efficient
solar powered LED lights.
Your Solar Security Light can light for up to 2 hours when the battery is fully
charged. With the adjustable TIME dials set to the maximum (+) position, you
can make the light last up to 60 seconds from last detected motion.
The 3 sealed rechargeable NiMH 2100 mAh batteries included with this product
should last for approximately 3 years before they need to be replaced.
40227
v10.2
2010
Once you have identified all parts, connect the solar
charge panel to your Solar Security Light by plugging
the 15 foot cord into the cord attached to the bottom of
the Solar Security Light. Firmly turn and twist the cords
while pressing together for a tight connection.
A screw for metal cover
3
Solar Security Light is ideal for areas where safety and security around your home is
needed, including entrance doors, driveways, carports, garages, decks, and porches.It
is also perfect for use in RV’s and other remote areas where electricity is not available.
Your Solar Security Light comes complete with a solar cell charge panel attached to a
15 foot power cord. For optimum sun exposure and longer light output, place the solar
panel (while attached to the main body) in a position that receives at least 6-8 hours of
direct sunlight per day. Placing the panel in a shaded location will not allow the battery
to charge fully, reducing the number of hours the light will operate per evening. Ensure
that the solar panel is not placed near night time light sources such as porch lighting or
street lighting.
Keep in mind that the motion sensor has a field of vision of 120 degrees at a distance
of 20 feet when the surrounding temperature is 75F.
2. Use the four wood/sheet metal screws supplied to mount the solar cell charge
panel onto a solid surface. You can adjust the angle of the solar cell by gently
rotating the solar cell to a different locking position. Remember to set the panel to
face direct sunlight exposure, optimally facing south.
1. Remove the screw on the right side of your Solar Security Light and slide out the
metal mounting bracket to install on the wall. You may install it vertically or more
horizontally by screwing onto a solid surface with the 2 supplied screws. Take the
main body of your Solar Security Light and fit it on the installed mounting bracket.
Front Back
Charge the batteries with the power switch on the main body of your Solar Flood
Light in the OFF position.
Leave the switch in this position for 3 days with the solar panel placed in direct
sunlight. This will ensure that the batteries in your Solar Flood Light have a full
charge prior to normal operation.
mounting
left side
slide down the battery cover.
6. Close the plastic cover and re-assemble the metal cover and the main body
together with the screw removed in step 3, ensuring the two parts are put together
securely.
7.
Front Back
The metal part right above the motion sensor can be rotated clockwise and counter-
clockwise to show or hide the 3 adjustment dials (TIME/SENS/LUX).
less than 10 When the charging ability of the batteries decrease, you can replace the batteries with
three new NiMH 2100 mAh batteries. Follow the steps below.
three new
rechargeable NiMH 2100 mAh batteries.
min.
remain
after the last motion is detected.
is at
bracket.
Andere MAXSA Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
