MaxTech PCI Internal Voice/FAX/Data/Speakerphone... Bedienungsanleitung

Part #MAN152 Rev. 1.0 V.90-CL

High Performance

V.90/V.34+/V.42bis

56K BPS

PCI Internal

Voice/FAX/Data/

Speakerphone

Modem

User's Manual

Contents

Section One - Introduction ..........................1

Section Two - Installation............................. 1

SectionThree-ATCommandSet ............... 6

Section Four - S Registers ........................ 13

SectionFive-ResultCodes ...................... 14

SectionSix-Troubleshooting.................... 15

SectionSeven-Supportand Service......... 17

Appendix A - Specifications ..................... 17

Appendix B - Notices ................................ 17

The information contained in this manual has been

validated at the time of this manual's production.

The manufacturer reserves the right to make any

changes and improvements in the product de-

scribed in this manual at any time and without

notice. Consequently the manufacturer assumes

no liability for damages incurred directly or indi-

rectly from errors, omissions or discrepancies be-

tween the product and the manual.

All registered trademarks are the property of their

respective owners.

ofthisdocumentinanyformispermittedwithoutprior

writtenauthorizationfromtheManufacturer.

Section One - Introduction

TheMaxTechXPVS56P/CPCIPlugandPlayData,

Fax,VoiceSpeakerphoneModemconnectsyourcom-

putertoallpopularhighspeedmodemsavailabletoday.

Themodemutilizes

V.90(56Kbps)

technologytoprovide

increased download speeds using regular telephone

lines.ThemodemincorporatesPlugandPlayforeaseof

installation.

Thismanualdescribesthehardwareinstallation

proceduresforyournewmodem.Additionalinformation

onATcommandsandS-registersisprovidedsothatyour

system can be customized for a particular operating

environment.

*Note:V.90iscapableofdownloadingat56Kbps.How-

ever,currentFCCregulationslimititsspeedsto53Kbps.

Section Two - Installation

Thissectionwillprovidestepbystepinstructions

on how to install your new 56 Kbps Data, Fax, Voice,

Speakerphonemodem.Installationofthismodemisatwo-

stepprocessconsistingof:1)hardwareinstallationand

2)communicationsoftwareinstallation.

2.1 UnpackingYourModem

Becertainthatyouhavealltheitemslistedbelow.

Thispackagecontains:

•Amodem •Atelephonecable

•User'smanual •Softwareforthemodem

•Software user'smanual

2.2 WhatYou Need

Youwill need:

1. A phillips-head screw driver.

2. A computer running Microsoft Windows 95 or

later.

3. AnavailablePCIslotinyourPC.

ProceedtoSection2.3nowifyouhaveevery-

thing required.

2.3 Hardware Installation

Installation of this modem requires opening and

manipulatingyourPC.Exercisecautionatalltimeswhen

working with AC powered and static-sensitive equip-

ment. Turn off and unplug your PC before installation.

Dischargeanystaticelectricityfromyourbodybytouch-

inganygroundedmetalsurfaceofthePCsystem,such

as its power supply cover.

1. Turn off and unplug your computer from the AC

outlet.

2. Remove your computer's cover (refer to your

computer's owner's manual).

3. Selectanyavailable32-bitPCIcardslotand remove

the slot cover (refer to Figure 2-3).

Figure 2-3 PCI Expansion Slots

4. Carefully slide the PCI internal modem into the slot

you have chosen, applying even pressure until the

modem is completely seated in the slot.

5. Fasten the retaining bracket with the screw from

the slot cover. Make sure the modem is properly

aligned. Store the slot cover for future use.

6. Replace the computer cover and plug in your com-

puter.

7. Connectthetelephonecablefromthemodem'sLINE

connector to the telephone wall jack.

8. Optionally, connect your telephone to the modem's

PHONE connector, a microphone to the MIC con-

nector and a speaker to the SPK connector.

9. Turn your computer on. Your modem is now in-

stalled.

2.4 Hardware Configuration

TheversionofWindows9xyouhavewilldetermine

which set of dialog boxes is presented to you when

installingthemodeminWindows9x.Proceedtooneofthe

following sections, depending on your Windows 9x's

diaglogbox:

• Section 2.4.1 when Windows 95 starts for

thefirsttimeaftercardinstallation,itdetects

themodemanditdisplaystheNewHard-

ware Found dialog box

• Section 2.4.1.1 when Windows 95 starts for

thefirsttimeaftercardinstallation,itdetects

themodemanditdisplaystheUpdateDevice

Driver Wizard.

• Section 2.4.1.2 When Windows 98 starts for

thefirsttimeaftercardinstallation,itdetects

theadapteranddisplaysthe Add New

Hardware Wizard.

2.4.1 Windows 95 Release 4.00.950

WhenWindows95startsforthefirsttimeaftercard

installation,itdetectsthemodemanddisplaystheNew

HardwareFound dialogbox.

Under New Hardware Found, when asked to

“Select which driver you want to install for your new

hardware,”clickon“Driverfromdiskprovidedbyhard-

waremanufacturer.”Click“OK.”

The Install From Disk dialog box now instructs

youto“Insertthemanufacturer'sinstallationdiskintothe

driveselected,andthenclickOK.”Insert themodem's

driver diskette into the disk drive and type A:\ (or B:\ if

inserted in drive B) in the “Copy manufacturer's files

from:”box.Click“OK.”

Windows95mayrequestitsowninstallationdisks

orCD-ROMforsomefiles.InserttheWindows95disks

or CD-ROM as required. When all necessary files are

copied,themodemisconfigured.Windows95willassign

themodemaCOMportandIRQline.ProceedtoSection

2.5.

2.4.1.2 Windows 98

WhenWindows98startsforthefirsttimeaftercard

installation,itdetectstheadapteranddisplaystheAdd

New Hardware Wizard.

Insertthediskthatcontainsyourmodemdriversinto

theappropriatedriveandclick“Next. Windows98willask

you"WhatdoyouwantWindowstodo" Select"Search

forthebestdriverforyourdevice".Click"Next". Windows

98 will find the driver on the driver disk. Click "Next".

Windowswillnowfindaseconddeviceonthemodem.

Makesurethatthedriverdiskisstillinthediskdriveand

click “Next.” Windows will find the second driver. Click

“Finish”tocompletetheinstallation.

Whenallnecessaryfilesarecopied,themodemis

configured.Windows98willassignthemodemaCOM

portandIRQline. Proceedto Section 2.5.

2.5 SoftwareInstallationandConfiguration

You are now ready to install and configure the

communicationsoftware.Refertoyoursoftwaremanual

forinstallationprocedures.

Wesuggestthefollowingcommunicationparam-

eters when you first use your data communication

2.4.1.1 Windows 95 Release 4.00.950 B

WhenWindows95startsforthefirsttimeaftercard

installation,itdetectsthemodemanddisplaystheUpdate

DeviceDriverWizard.Insertthedriverdiskintothedisk

driveandclick“Next.”Windowswillfindthedriveronthe

driverdisk.Click“Finish.Windows95mayrequestitsown

installationdisksorCDforsomefiles.InserttheWindows

95disks orCDasrequired.

Windows will now find a second device on the

modem.Makesurethatthedriverdiskisstillinthedisk

drive and click “Next.” Windows will find the second

driver.Click“Finish”tocompletetheinstallation.

Whenallnecessaryfilesarecopied,themodemis

configured.Windows95willassignthemodemaCOM

portandIRQline. Proceedto Section 2.5.

software.Consultthesoftwaremanualforinformationon

usingtheseandotherparameters/features.

115,200 bps; 8 data bits; no parity; 1 stop bit;

RTS/CTSflowcontrolsetto“on;”initialization

string: AT&F

Selecta“GenericClass1”modemtypeinyourfax

software

Note that your software must be configured to

communicatewiththemodemonthesameCOMportand

IRQlineusedbythemodem.

2.6 TestingYourModemAfterInstallation

Inordertotestyourmodemyoushouldbefamiliar

withyourcommunicationsoftware.Loadandsetupyour

communicationsoftwareandenterinto“terminalmode.”

Make sure that the COM Port and IRQ settings of the

modemmatchthe software.TypeATon yourterminal

screenandpressENTER.Youmaysee“AT”,“AATT”or

nothingonthe screen.Inallcases,themodemshould

respondwithanOKor0.Ifitdoesnot,eitherthemodem

hasnotbeeninstalledproperlyorthesoftwarehasnot

beenproperlyconfigured.ReviewSections2.2-2.5 and

becertainthatthemodemandthesoftwarehavebeen

properly installed. If required, refer to Section 6 for

additional troubleshootinginformation.

2.7 UsingYourModem

Thesoftwareincludedwithyourmodemproduct

providesauserfriendlyinterfacetoaccessthefax,data

andvoice/speakerphonefunctionsofyourmodem.

This

software should be sufficient for all of your com-

municationneeds

.Theremaybetimeswhenyouneed

toaccessthemodemmanuallyviamodemcommands.

ReadSection3forasummarydescriptionofthemodem

commandsetbeforemanuallyaccessingthemodem.You

maywanttoreadthesoftwaremanualfirst,however,as

thesoftwaremayalreadyprovideauserfriendlymethod

of accessing the functions you need (i.e. dialing or

answering calls).

2.8 Where To Go From Here

Youshouldfamiliarizeyourselfwiththefunctions

available from the included software by reading its

manual. You will be accessing most, if not all, of the

modem'sfunctionsfromthis software.Youmayalsouse

anyothercommerciallyavailable communicationsoft-

ware with the modem. Read Section 3 only if you are

interested in accessing the modem manually, and not

throughtheincludedsoftware.Section4and5contain

reference material, and can be skipped. If you have

difficultiesgettingyourmodemtowork,readSection6

Troubleshooting,

to find answers to commonly asked

questionsandproblems.

Section Three - AT Command Set

3.1 ExecutingCommands

Commandsareacceptedbythemodemwhileitisin

CommandMode.YourmodemisautomaticallyinCommand

Mode until you dial a number and establish a connection.

CommandsmaybesenttoyourmodemfromaPCrunning

communicationsoftwareoranyotherterminaldevices.

Yourmodemiscapableofdatacommunicationatrates

of:300,1200,2400,4800,9600,14400,19200,28800,38400,

57600and115200bps.MakesureyourCOMportbaudrate

settingsinyourcommunicationssoftwareissettooneofthe

abovespeeds.

3.2 Command Structure

Allcommandssenttothemodemmustbeginwith

ATandendwithENTER.Allcommandsmaybetypedin

eitherupperorlowercase,butnotmixed.Tomakethe

commandlinemorereadable,spacesmaybeinserted

between commands. If you omit a parameter from a

command that requires one, it is just like specifying a

parameterof0.

Example:

ATH[ENTER]

Thiscommandcausesyourmodemtohangup.

3.3 BasicAT Commands

In the following listings, all default settings are

printedin bold text.

Command Function

AManually answer incoming call

A/ Repeat last command executed. Do not

precedeA/withATorfollowwithENTER

AT Appears at the beginning of every

commandline

B_ B0 CCITTmode

B1 Bell mode

B2 V.23 at 1200/75

B3 V.23 at 75/1200

C_ C0 Carrier always off

C1 Normal transmit carrier

D_ 0 - 9, A-D, # and *

P pulse dialing

R originate calls in answer mode

T touch-tone dialing

W wait for second dial tone

, pause

@ wait for five seconds of silence

! flash

; return to Command Mode after dialing

DS=n Dial one of the four telephone numbers

(n=0-3) stored in the modem’s non-

volatilememory

E_ E0 Commands are not echoed

E1 Commands are echoed

F_ F0 Enables online echo

F1 Disables online echo

+++ TIES Escape Characters - Switch from

DataModetoCommandMode

H_ H0 Force modem on-hook (hang up)

H1 Force modem off-hook (make busy)

I_ I0 Display product-identification code

I1 FactoryROMID

I2 Internal memory test

I3 DeviceID

I4 Reserved

I5 Modem chip hardware configuration

I6 Country code

I7 Board manufacturer firmware version

I8 Modem firmware version

I10 Modem board configuration

L_ L0 Low speaker volume

L1 Low speaker volume

L2 Medium speaker volume

L3 High speaker volume

M_ M0 Internal speaker off

M1 Internal speaker on until carrier

detected

M2 Internal speaker always on

M3 Internalspeakeronuntilcarrierdetected

and off while dialing

N_ N0 Connect only at DTE rate

N1 Automatic rate negotiation

O_ O0 Return to Data Mode

O1 Return to Data Mode and initiate an

equalizer retrain

O3 Renegotiates rate and then returns to

data mode

PSet Pulse dial as default

Q_ Q0 Modem sends responses

Q1 Modem does not send responses

n=0-33

Read and display value in register n

Set register

(n=0-33; x=0-255)

TSet Tone Dial as default

V_ V0 Numeric responses

V1 Word responses

W_ W0 Modem reports DTE response

codes

W1 Modem reports DTE response codes

W2 Modem reports DCE response codes

W3 Modem reports DTE speed, modulation

mode, error control, data compression,

DCE transmit and receive speed

W4 Modem reports protocol, data

compression and DTE data rate

X_ X0 Hayes Smartmodem 300 compatible

responses/blind dialing

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MaxTech Modem Handbücher

MaxTech

MaxTech xps336ir V.34/V.42bis Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

MaxTech

MaxTech xm144ic V.32bis Bedienungsanleitung

MaxTech

MaxTech xpm56i 56K BPS Bedienungsanleitung

MaxTech

MaxTech xpvs336i Bedienungsanleitung

MaxTech

MaxTech 28 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung