Maytag DAX3000AX Series Bedienungsanleitung

1 EA INSTALLATION MANUAL

1 EA BEZEL

2 EA MOUNTING TRIM STRIPS

8 EA PANEL MOUNTING SCREWS

5 EA MOUNTING TAPE SQUARES

2 EA HEAVY DUTY SPRINGS

JETCLEAN II WOOD PANEL KIT

DAX3000AX*/DAX3090AX*

Parts List:

Tools you will need:

Circular Saw or Table Saw

Tape Measure

Electric Drill

Torx (T-20) Head Screwdriver

Phillips Head Screwdriver

1/8” Drill Bit

3/8” Drill Bit

Carpenter’s Glue (for use with 1/4” wood panels)

Masking Tape

Safety Glasses

Original Installation Instructions that came with your dishwasher

Things You Will Need to Know During the Installation:

• The Wood Panel Type you plan on installing: 1/4”3/4”

Part No. 6 918172 A 1 INSTALLATION INSTRUCTIONS

ALL ELECTRICAL WIRING, GROUNDING AND PLUMBING SHOULD BE DONE IN

ACCORDANCE WITH NATIONAL AND LOCAL CODES BY QUALIFIED INDIVIDUALS.

CHECK LOCAL PLUMBING CODES

FOR APPROVED PLUMBING

PROCEDURES AND ACCESSORIES.

This appliance must be connected to a

grounded metal, permanent wiring system;

or an equipment-grounded conductor must

be run with the circuit conductors and con-

nected to the equipment-grounding terminal

or lead on the appliance.

This dishwasher is designed for operation on

an individual 120 VAC, 60 Hz grounded

electrical circuit. Use required fuse (15 amp)

or comparable circuit breaker. Two wire

with ground service to the dishwasher is rec-

ommended for connection at the terminal

box and for grounding.

BEFORE YOU BEGIN: In Step 5, the unit may need to be removed from the cabinet during the installa-

tion of the heavy-duty springs. A qualified electrician and/or plumber, as necessary, should be used to

make any electrical or plumbing connections during that installation.

Panel Installation Instructions for a Jetclean II Dishwasher:

Step 1: Make the Wood Panel

• Cut the wood panel to the size shown in Figure 1.

The height of your wood panel will be one of two

sizes depending on which DAX Kit you have.

For DAX3000 Kits: Dimension A = 25”

For DAX3090 Kits: Dimension A = 25 15/16”

FIGURE 1- Panel Dimensions

Part No. 6 918172 A 2 DAX3000AX*/DAX3090AX*

Step 1.1: For 1/4” Wood Panels ONLY.

For 3/4” Thick Wood Panels, go to Step 1.2.

• In addition to the rectangular face of

the wood panel, you will need to cut

the pieces shown in Figure 2.

Note: All pieces are 1/2” thick.

For DAX3000 Kits: Dimension B = 24 3/4”

For DAX3090 Kits: Dimension B = 23 11/16”

• Glue the shims you just made to the back of the 1/4” thick

wood panel as shown in Figure 3 using Carpenter’s glue

(yellow glue). With a damp rag, wipe up any excess glue

squeezed out while the glue is still wet.

• Apply gentle pressure and allow glue to dry fully before

attempting to assemble the wood panel to the door.

Drying time for the glue may be up to 24 hours. Read the

glue bottle for more complete drying time information.

After the glue has dried, it can be scraped off using a

putty knife and sanded smooth, if necessary.

Step 1.2: All Wood Panel Types.

• In order to drill the holes to attach the bezel, you will need to use the bezel as a drill guide. Place the

wood panel face down on your work surface with the top of the panel pointing at you.

• Align the bezel along the top of the wood panel, centered from left to right as it is shown in Figure 4.

The tabs of the bezel now contact the back of the wood panel.

Figure 2 – Shim Dimensions

FIGURE 3 – Shim Placement Pattern

Part No. 6 918172 A 3 DAX3000AX*/DAX3090AX*

Step 1.2, cont’d:

FIGURE 4 – Alignment of the Bezel to the Panel or Top Shim

• Drill through the center of the holes in the tabs on the bottom of the bezel with the 1/8” drill bit. Drill

far enough to locate the holes without drilling too deep. Do not drill more than 1/2” into the wood.

• Once you have marked the center of the holes with the 1/8” drill bit, come back with the 3/8” bit to cut

the final size and the final depth of 1/2”.

TIP: Use masking tape on your drill bit to mark a maximum drill depth of 1/2” so you won’t drill all the

way through your wood panel.

Step 2:Apply Panel to Door Temporarily.

• Disconnect power to dishwasher at the circuit breaker.

• Remove one side of the backer from tape strips and apply to the back of the panel in the locations

shown in Figure 5.

TIP: Before removing the backing strips on the foam tape, try dry fitting the panel to the bezel. It will

help improve your feel for the process before you apply the wood panel to the door. Once the sticky

side of the foam tape has been pressed to the door, it can not be removed without damage to the

foam tape.

Part No. 6 918172 A 4 DAX3000AX*/DAX3090AX*

Step 2, cont’d:

• Remove the backer material from all five (5) pieces

of mounting tape now applied to the back of the

wood panel.

• Slip the tabs on the upper edge of the bezel up under

lower lip of the control panel.

• Center the wood panel under the bezel making sure

the holes drilled near the top edge of the back side

of the wood panel align with the posts protruding

from the bottom tabs of the bezel. This will ensure

the bezel and panel are aligned properly.

• Press the wood panel firmly onto the dishwasher to

make sure the foam tape makes good contact.

Step 3: Attach Mounting Trim to Door

• Carefully lower door until it is all the way down. It

may now seem quite heavy. Later, you will adjust the

springs to compensate for the weight of the door.

• Loosen the six (6) screws indicated in Figure 6 using

the T-20 screwdriver until they are about 1/4” above

the plastic Inner Door, or about 4 full turns.

• Insert the Mounting Trim Strip into the space provided

between the plastic Inner Door and the Steel Outer Door

that came with your dishwasher as is shown in Figure 7.

Make sure the holes for the mounting screws line up with

the holes in the steel Outer Door and the plastic Inner Door.

FIGURE 6 – Mounting Screws to be Removed

FIGURE 5 – Foam Tape Placement

FIGURE 7 – Mounting Strip Placement

Part No. 6 918172 A 5 DAX3000AX*/DAX3090AX*

Step 3, cont’d:

• Retighten all six (6) screws you just loosened. Torque them until hand-tight.

• The Mounting Trim Strips should now wrap around the wood panel and the original outer portion of

the door.

• Close and latch the door.

Step 4:Attach Mounting Trim to Wood Panel

• Drill pilot holes for the Panel Mounting Screws through the four (4) holes on each side in the Mounting

Trim Strips using the 1/8” drill bit. Piloting the holes will help keep your wood from splitting where the

screw enters.

• Drive the Panel Mounting Screws provided with the kit through the Mounting Trim Strips into the wood

panel.

Step 5: Adjust Springs

Note: If your wood panel weighs more than 4 lbs., you will need the heavy-duty springs provided in

this kit.

TIP: To prevent damage to the Toe Panel Assemblies, remove the four lower mounting screws using a

1/4” socket screwdriver or a Phillips head screwdriver and set the panels aside while you are adjusting

the springs.

• Remove both of the Toe Panel Assemblies using a 1/4” socket screwdriver or a Phillips head screwdriver.

• Visually check to make sure you have enough slack in your electrical connection, water line connection

and drain hose connection to remove the unit approximately one (1) foot.

Note: If you do not have enough slack in your connections, you will need to turn off the water

beneath the sink and disconnect any necessary connections. Refer to your Original Installation

Instructions for more information regarding the location of these connections. All electrical wiring,

grounding and plumbing should be done in accordance with national and local codes by quali-

fied individuals.

• Using a Phillips head screwdriver, remove the mounting screws from the side mounting strips

attached to the cabinet pull the unit out of the cabinet approximately one (1) foot.

CAUTION: The top of the dishwasher should be held to

prevent the dishwasher from tipping forward when the door is

opened with the mounting screws removed.

Part No. 6 918172 A 6 DAX3000AX*/DAX3090AX*

Step 5, cont’d:

• Remove the original springs and replace them with the heavy-duty springs provided in your kit

according to Table 8.

Table 8 – Spring Usage Based on Total Panel Weight

• Adjust the spring tension as shown in Figure 9 until the

door moves up and down smoothly.

• Push the unit back into the cabinet and re-mount using

the screws you just removed from the side mounting

strips. Using your Original Installation Instructions,

reconnect any electrical, water or drain connection you

disconnected earlier.

• Be sure there are no leaks in any of the four (4) water or

drain connection locations.

• Re-mount the Toe Kick Panel using the screws you

removed when beginning the heavy-duty spring installa-

tion. Make sure the toe panel fits tightly against the

floor.

• Re-mount the Toe Panel Assemblies to the frame.

Step 6: Return power to dishwasher.

• Turn power to the dishwasher back on at the fuse or circuit breaker.

• The Dishwasher is ready to run.

• Run one (1) Rinse/ Hold cycle to verify that all connections are in place and working properly.

Total Wood

Panel Weight No. of Original

Springs Needed No. of Heavy-Duty

Springs Needed

0 to 4 Lbs. 2

4 to 7 Lbs. 1 1

7 to 13 Lbs. 2

FIGURE 9 – Spring Tension Adjustment

Part No. 6 918172 A 7 DAX3000AX*/DAX3090AX*

1 Manual de instalación

1 Bisel

2 Bandas laterales de montaje

8 Tornillos para montaje del panel

5 Cuadrados adhesivos de montaje

2 Resortes de gran resistencia

Lista de piezas:

Herramientas que necesitará:

Sierra circular o sierra de mesa

Cinta métrica

Taladro eléctrico

Destornillador de cabeza Torx (T-20)

Destornillador de cabeza Phillips

Broca de 1/8”

Broca de 3/8”

Cola para carpinteros (para usar con los paneles de madera de 1/4”)

Cinta de enmascarar

Anteojos de seguridad

Instrucciones originales de instalación que vienen con su lavavajillas

Lo que necesita saber durante la instalación

• El tipo de panel de madera que tiene planeado instalar: 1/4” 3/4”

Pieza No. 6 918172 A 8 INSTRUCCIONES DE INSTALACIÓN

Kit para el panel de madera JetClean II

DAX3000AX* / DAX3090AX*

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Maytag Spülmaschine Handbücher

Maytag

Maytag MDB7759AWB Bedienungsanleitung

Maytag

Maytag MDB7759AWW4 Bedienungsanleitung

Maytag

Maytag MDB8959SBBK Jetclean Plus Bedienungsanleitung

Maytag

Maytag Jetclean III MDB3700AW Bedienungsanleitung

Maytag

Maytag MDB6759AWW - 24 Inch Fully Integrated... Bedienungsanleitung

Maytag

Maytag MDB8979SFZ Bedienungsanleitung

Maytag

Maytag MDB7851AWQ - 24 Inch Full Console Dishwasher Gebrauchsanweisung

Maytag

Maytag MDB7749SAM0 Bedienungsanleitung

Maytag

Maytag Jetclean Plus MDB6709AW Bedienungsanleitung

Maytag

Maytag MDB-7 Bedienungsanleitung

Maytag

Maytag MDB4601AWX Bedienungsanleitung

Maytag

Maytag DWU5915BAX Bedienungsanleitung

Maytag

Maytag MDB7809AWB0 Bedienungsanleitung

Maytag

Maytag MDB8959SBS2 Bedienungsanleitung

Maytag

Maytag MDB8959SBW3 Bedienungsanleitung

Maytag

Maytag MDB6709AWQ - Jetclean Plus 24 in. Dishwasher Bedienungsanleitung

Maytag

Maytag MDB8859AWB0 Bedienungsanleitung

Maytag

Maytag MDB8859AWB - Jetclean Plus 24 in. Dishwasher Bedienungsanleitung

Maytag

Maytag W10596271A Bedienungsanleitung

Maytag

Maytag Jetclean MDB6800 Bedienungsanleitung

Maytag

Maytag Performa PDB1600AW Series Bedienungsanleitung

Maytag

Maytag ADB3500AW Series Bedienungsanleitung

Maytag

Maytag MDB4000 Bedienungsanleitung

Maytag

Maytag 6 915555 B Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

KitchenAid

KitchenAid KUDB230B Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung