Maytag MFF2558KEB Bedienungsanleitung

French Door

Use & Care Guide

Form No. A/03/04 Part No. 12828104 www.maytag.com Litho U.S.A.

Table of Contents

Important Safety

Instructions .................................... 1-2

Installation ..................................... 3-9

Temperature Controls.................... 10

Fresh Food Features ................ 11-13

Freezer Features ............................. 13

Ice And Water...................................14

Water Filter .................................15-16

Food Storage Tips .................... 17-19

Care and Cleaning................... 20-23

Operating Sounds .......................... 24

Troubleshooting........................ 25-27

Warranty & Service ........................ 29

Guide d’utilisation et

d’entretien........................................ 30

Guía de uso y cuidado .................. 59

Important Safety Instructions

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

WARNING

DANGER – Immediate hazards which WILL result

in severe personal injury or death.

DANGER

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury or property damage.

CAUTION

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact your dealer, distributor, service agent or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground) prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

To reduce risk of injury or death, follow basic

precautions, including the following:

IMPORTANT: Child entrapment and suffocation

are not problems of the past. Junked or abandoned

refrigerators are still dangerous – even if they sit out

for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

•Take off the doors.

•Leave the shelves in place so

children may not easily climb

inside.

DANGER

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this Use & Care

Guide for future reference, it provides the proper use

and maintenance information.

Keep sales receipt and/or cancelled check as proof

of purchase.

Call: 1-800-688-9900 U.S.A.

1-866-688-2002 Canada

Have complete model and serial number

identification of your refrigerator. This is located on a

data plate inside the refrigerator compartment, on

the upper left side. Record these numbers below for

easy access.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

To reduce risk of fire, electric shock, serious

injury or death when using your refrigerator,

follow these basic precautions, including the

following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure this appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

115 volt, 15 amp., 60 cycle line.

8. Do not modify plug on power cord. If plug does

not fit electrical outlet, have proper outlet installed

by a qualified electrician.

9. Do not use a two-prong adapter, extension cord

or power strip.

10. Do not remove warning tag from power cord.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any part of refrigerator

unless specifically recommended in Use & Care

Guide or published user-repair instructions. Do

not attempt service if instructions are not under-

stood or if they are beyond personal skill level.

13. Always disconnect refrigerator from electrical

supply before attempting any service. Disconnect

power cord by grasping the plug, not the cord.

14. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and grounding must comply with local

codes and be made by licensed personnel when

required.

15. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

16. Replace worn power cords and/or loose plugs.

17. Always read and follow manufacturer’s storage

and ideal environment instructions for items being

stored in refrigerator.

18. Your refrigerator should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any

part of the refrigerator.

20. Clean up spills or water leakage associated with

water installation.

Important Safety Instructions

SAVE THESE INSTRUCTIONS

WARNING

ABA

Installation

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Location

•Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

•Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction may

occur at this temperature.

•Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow 1⁄2" space at top and 1⁄2" space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a recess

where the top of the refrigerator is completely covered,

use distance from floor to top of hinge cap to verify

proper clearance.

Transporting Your Refrigerator

•NEVER transport refrigerator on its side. If an upright

position is not possible, lay refrigerator on its back.

Allow refrigerator to sit upright for approximately 30

minutes before plugging it in to assure oil returns to

the compressor. Plugging the refrigerator in

immediately may cause damage to internal parts.

•Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–NEVER from its front.

•Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

•Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening restraints

may dent or damage outside finish.

•Use slight pressure to pry the

cover loose.

•Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

Leveling

To protect property and refrigerator from damage,

observe the following:

•Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

•Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be level.

Note

•Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed

•3⁄8" hex head driver

•Carpenter’s level

1. Remove toe grille.

•Grasp firmly and pull outward

to unclip.

2. Remove bottom hinge cover(s).

•Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

3. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

Installation

To avoid electrical shock which can cause severe

personal injury or death, observe the following:

•Disconnect power to refrigerator before removing

doors or drawer. Connect power only after

replacing doors or drawer.

WARNING

To avoid damage to walls and flooring, protect vinyl

or other flooring with cardboard, rugs or other

protective material.

CAUTION

1. Unplug power cord from power source.

2. Remove toe grille and bottom hinge

cover(s) (see page 3).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

4. Unscrew 5⁄16" hex head screws from

top hinge to remove hinge and retain

all screws for later use.

5. Lift right side refrigerator door from

center hinge pin. Remove door

closure from center hinge pin on

the right side and retain for later

use.

6. Disconnect wire harness on top

of left side refrigerator door top

hinge.

Release two-pin connector by

pressing junction point with a

flat blade screwdriver or

fingernail.

Green ground wire remains

attached to the hinge.

7. Unscrew 5⁄16” hex head screws from

top hinge to remove hinge and retain

for later use.

Lift left side refrigerator door, along

with top hinge, from center hinge pin.

Remove center hinge pin with a 5⁄16”

hex head driver and retain hinge pin

for later use.

8. Remove Phillips screws to remove

right and left hinges and retain all

screws for later use.

9. Remove both stabilizing brackets

with 3⁄8" hex head driver and retain

screws for later use.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

right

side

door

closure

4. Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

5. Using the carpenter’s level, make sure front of

refrigerator is 1⁄4" (6 mm) or 1⁄2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

6. Turn stabilizing legs (C) clockwise until firmly

against floor.

7. Turn adjustment screws (A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

8. Replace hinge cover(s).

•Position cover into the outer edge of the hinge.

•Swing the cover toward the cabinet and snap it

into place.

9. Replace the toe grille.

Note

•For proper reinstallation, ensure the “top” marking

on the interior of the toe grille is oriented correctly.

•Align the toe grille mounting clips with the lower

cabinet slots.

•Push the toe grille firmly until it snaps into place.

Installation

Pullout Freezer Drawer

To avoid electrical shock which can cause severe

personal injury or death, disconnect power to

refrigerator before removing doors. After replacing

doors, connect power.

WARNING

To prevent accidental child entrapment or

suffocation risk, do not remove the divider in the top

freezer basket.

DANGER

To avoid possible injury, product, or property

damage, you will need two people to perform the

following instructions.

CAUTION

2. While supporting door front,

hook supports into tabs

located on inside of rail.

To Install:

1. Pull both rails out to full

extension.

3. Lower door front into

final position.

4. Place the basket cradles back onto the side rails.

Align snaps with the slots on the side rails and

press each snap towards the rail until it clicks.

5. With rails pulled out to full extension, set the

basket straight down into the basket cradles.

6. Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

Basket cradle

snap attachments

5. Lift top of drawer front

to unhook supports

from rail system. Lift

door front out to

remove.

To Remove:

1. Pull drawer open to full extension.

2. Pull upper basket out to full extension and lift out

to remove.

3. Lift lower basket straight up and out to remove.

4. On each side rail is a

basket cradle with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the side

rail system. Lift the cradles

off of the rails.

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Front Mount Handle

Materials Needed

•Gloves to protect hands

•Phillips screwdriver

•Plastic door removal card (or 1⁄32" thick plastic card),

retain the card

Attach Extensions to Handle:

1. Align handle and

extension as shown.

2. Place extension in

handle opening.

3. Apply slight pressure

to both sides of the extension piece.

4. Slide extension until it stops on inside edge of

handle.

To Install:

1. The handles are to be oriented

as shown.

2. Align front mount door handle

clip with the door tabs.

Door Reinstallation

1. Install hinge assemblies:

•Install top hinge loosely with 5⁄16" hex head

screws.

•Install center hinge with Phillips

screws.

2. Place hinge side of refrigerator door

on center hinge pin.

3. While holding refrigerator door

upright, tighten down top hinge

with 5⁄16" hex head driver.

4. Reconnect two-pin connector.

5. Replace top hinge covers.

Installation

6. Align bottom of handle with lower

door tab. Press upper handle end to

door surface and firmly grasp lower

end of handle. Gently slide handle

upward until bottom of handle

settles on door surface, then

reverse direction, sliding downward

to almost engaging tab with clip.

7. Grasp the handle firmly and slide

down until it clicks. The audible

click indicates fastening clips are

securely interlocked.

2. Grasp the lower part of the handle

firmly and lift to remove.

To Remove:

1. Flex the handle away from the door

panel. Simultaneously place door

handle removal card underneath

the base of the lower handle. Insert

the card to the line or until it stops.

5. Push the handle down against the

upper door tab just enough to

allow it to hang unsupported.

4. Rotate the handle so that the

handle is flat against the door.

3. Ensure the handle clips are

positioned slightly above the

door tabs.

Handle

Clip

Door

Tab

Installation

Notes

•There is a slight curve to

the freezer handle.

•For proper installation, be

sure handle is oriented as

shown.

To Install:

1. Align door handle clips slightly to the left of the

tabs attached to the freezer door.

2. Rotate the handle so the left base is flat against

the door.

Freezer Handle

Materials Needed

•Gloves to protect hands.

•Phillips screwdriver.

•Plastic handle removal card (or 1⁄32" thick plastic

card). Retain the card.

4. While firmly supporting the left handle base against

the door, align the right base of the handle with the

right tabs that are attached to the door.

5. Now, while firmly holding the handle at the left and

right bases, gently slide the handle towards the

right until the right base settles in. The handle

should now be flat against the face of the freezer

door at both the left and right bases.

6. With hands still firmly keeping the handle flat

against the freezer door, you may have to reverse

directions momentarily to assure clip/tab

engagement. Then firmly slide the handle to the

right until it clicks. The audible "click" indicates

that the fastening clips are securely interlocked.

To Remove:

1. At the right end, flex the handle base away from

the surface of the freezer drawer. Simultaneously

slide the door handle removal card that came with

your refrigerator under the right side base of the

handle. Slide the card to the line indication or until

it stops, which will be approximately 11⁄2".

2. With both hands, firmly grasp the handle towards

the right base.

3. Slide towards the left, lift and remove from the

surface.

Handle

Clip

Handle

Base

Door

Tab

3. Push the left handle

base against the left

door tab and slightly

to the right, just

enough to allow it to

hang unsupported.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

IMPORTANT: Do not overtighten. Cross

threading may occur.

6. Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

Connecting the Water Supply

To reduce the risk of injury or death, follow

basic precautions, including the following:

•Read all instructions before installing ice maker.

•Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

•Observe all local codes and ordinances.

•Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

•Disconnect power to refrigerator before installing

ice maker.

•Water damage due to an improper water

connection may cause mold/mildew growth. Clean

up spills or leakage immediately!

WARNING

To avoid property damage or possible injury,

follow basic precautions, including the

following:

•Consult a plumber to connect 1⁄4" O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

•Confirm water pressure to water valve is between

35 and 100 pounds per square inch, 20 pounds

per square inch without filter.

•Do not use a self-piercing, or 3⁄16" saddle valve.

Both reduce water flow and can become clogged

over time, and may cause leaks if repair is

attempted.

•Tighten nuts by hand to prevent cross threading.

Finish tightening nuts with pliers and wrenches.

Do not overtighten.

•Wait two to three hours before placing refrigerator

into final position to check and correct any water

leaks. Recheck for leaks after 24 hours.

•Verify the copper tubing under the sleeve is

smooth and free from defects. Do not reuse an old

sleeve.

CAUTION

Installation

Materials Needed

•1⁄4" outer diameter flexible copper tubing

•Shut-off valve (requires a 1⁄4" hole to be drilled into

water supply line before valve attachment)

•Adjustable wrench

•1⁄4" hex nut driver

Note

•You should only use copper tubing for installation.

Plastic is less durable and can cause damage.

•Add 8’ to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2’ diameter).

Avoid kinks in the copper tubing

when bending it into a service

loop. Do not use plastic tubing.

2. Remove plastic cap from water valve inlet

port.

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the use and care

packet.

4. Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink – so that tubing feeds straight

into inlet port.

2’ diameter

minimum

Installation

To avoid electrical shock which can cause severe

personal injury or death, DO NOT attempt to

remove the hinged seal from the fresh food

section.

WARNING

To avoid possible product damage, ALWAYS verify

that the hinged seal is folded against the edge of

the door prior to closing.

CAUTION

hinged seal

Opening and Closing Your

Fresh Food Doors

Your new refrigerator is uniquely designed with two

fresh food doors. Either door can be opened or closed

independently of one another.

There is a vertically-hinged section on the left fresh

food door. When the left door is closed, the hinged

section automatically forms a seal between the two

doors when both doors are closed.

When the left door is opened, the hinged seal

automatically folds inward so that it is out of the way.

Inhaltsverzeichnis

Sprachen:

Andere Maytag Kühlschrank Handbücher

Maytag

Maytag MSD2578VEB - 25.4 cu. Ft. Refrigerator Bedienungsanleitung

Maytag

Maytag MSF22D4XAM Bedienungsanleitung

Maytag

Maytag MZD2663KEW - 26 cu. Ft. Wide-By-Side... Handbuch

Maytag

Maytag MBF2254HEB14 Fehlerbehebungshandbuch

Maytag

Maytag MSD2550VEB00 Fehlerbehebungshandbuch

Maytag

Maytag W10213157A Bedienungsanleitung

Maytag

Maytag MSD2274VEM Bedienungsanleitung

Maytag

Maytag MSF25D4XAM00 Bedienungsanleitung

Maytag

Maytag Performa MBF1956HES Bedienungsanleitung

Maytag

Maytag MSF21D4MD Bedienungsanleitung

Maytag

Maytag MCD2358WEB - 23' Cabinet Depth Refrigerator Bedienungsanleitung

Maytag

Maytag MFI2269FRZ Bedienungsanleitung

Maytag

Maytag MSD2273VEB Montageanleitung

Maytag

Maytag RTD1700AAL Bedienungsanleitung

Maytag

Maytag MCD2257KES - 21.6 cu. Ft Bedienungsanleitung

Maytag

Maytag MZD2669KE Series Bedienungsanleitung

Maytag

Maytag MFC2061HE Series Bedienungsanleitung

Maytag

Maytag MSD2550VEB01 Fehlerbehebungshandbuch

Maytag

Maytag Performa PCF1700ACW Bedienungsanleitung

Maytag

Maytag MFW2055YEB00 Bedienungsanleitung

Maytag

Maytag ACD2234HR*ACD2238HT Series Montageanleitung

Maytag

Maytag performa Bedienungsanleitung

Maytag

Maytag 23inch Bedienungsanleitung

Maytag

Maytag MFD2561HEQ14 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung