MC Electronic DORADO MX3 Bedienungsanleitung
–
INSTRUCTIONS FOR USE
DORADO MX3
NO. 1611-MX
OEM-EN
REV. 2 EN
Instructions for use
Dorado MX3 kit
2
This product meets the EMC standards as determined in the
2004/108/EC directive and subsequent amendments and reference to the applied
EN ISO 14982 standard
Manufacturer : MC elettronica S.r.l.
Address : Via E. Fermi, 450/486
Fiesso Umbertiano (ROVIGO) - ITALY
Tel. +39 0425 754713 Fax +39 0425 741130
E-mail: mcstaff@mcelettronica.it
Internet: www.mcelettronica.it
Manual code : 1611MX3-OEM-EN
Issued : July 2017
Edition : November 2018
MC elettronica S.r.l. is not obliged to give notice of any further modifications of the
product.
The information given in this manual does not allow unauthorised personnel to
tamper with the product in any way.
The warranty on the equipment will no longer be valid if tampering should be
detected.
© Copyright MC elettronica 2018
Instructions for use
Dorado MX3 kit
3
Contents
1. Rules and general warnings ................................................................................ 5
1.1 Introduction ....................................................................................................... 5
1.2 Terms of the warranty ....................................................................................... 6
1.3 Service .............................................................................................................. 6
2. General description .............................................................................................. 7
3. System installation ............................................................................................... 8
3.1 Electrical connections ..................................................................................... 10
3.2 Virtual Terminal assembly ............................................................................... 12
3.3 Sensor installation ........................................................................................... 13
3.3.1 Speed sensor installation...................................................................... 13
3.3.2 Magnetic sensor installation ................................................................. 14
3.3.3 Seed sensor and the wiring harness installation ...................................... 15
3.3.4 Radar sensor and GPS installation .......................................................... 17
3.4 Operation ........................................................................................................ 18
3.4.1 Seed sensor recognition .......................................................................... 18
3.5 Keyboard operation ......................................................................................... 20
3.5.1 Start-up screen ........................................................................................ 20
3.5.2 Main screen ............................................................................................. 21
3.5.3 Variable range screen .............................................................................. 23
3.5.4 Main Parameter Screen ........................................................................... 24
3.5.5 Programming screens .............................................................................. 25
3.6 Graphic interface description .......................................................................... 26
3.6.1 Seed drill work screen .............................................................................. 26
4. Programming ...................................................................................................... 33
4.1 Virtual Terminal programming ......................................................................... 34
4.1.1 Date and Time setting .............................................................................. 35
4.1.2 Dimmer settings ....................................................................................... 36
4.2 Seeding ECU programming ............................................................................ 37
4.2.1 Main parameters ...................................................................................... 37
4.2.2 Menu ........................................................................................................ 38
5. Virtual Terminal software update ...................................................................... 55
6. ECU software update .......................................................................................... 57
7. Programmable parameters ................................................................................ 58
8. Alarms .................................................................................................................. 59
9. Maintenance ........................................................................................................ 60
9.1 Routine maintenance ...................................................................................... 60
9.1.1 How to protect the main connector .......................................................... 60
10. Troubleshooting................................................................................................ 61
11. Technical data ................................................................................................... 62
11.1 Virtual Terminal 3.5” ...................................................................................... 62
Instructions for use
Dorado MX3 kit
4
11.2 ECU SEM12-CR ............................................................................................ 62
11.3 ECU SEM12-ER ............................................................................................ 62
11.4 ECU gateway ................................................................................................ 63
11.5 Accessories ................................................................................................... 63
11.5.1 Pipe seed sensors .................................................................................. 63
11.5.2 Bracket seed sensors ............................................................................. 63
11.5.3 Proximity inductive sensor ...................................................................... 63
11.5.4 Magnetic sensor ..................................................................................... 63
Instructions for use
Dorado MX3 kit
5
1. Rules and general warnings
1.1 Introduction
This instruction manual provides all specific information needed to know and
correctly use the equipment.
After buying the Monitor, read the manual carefully and refer to it any time you have
doubts on how to use the equipment or when you have to carry out maintenance
operations.
Keep the manual on the machine. If this is not possible, keep it ready at hand.
ALL RIGHTS RESERVED. THIS MANUAL IS INTENDED FOR CUSTOMERS ONLY. ANY
OTHER USE IS FORBIDDEN.
Instructions for use
Dorado MX3 kit
6
1.2 Terms of the warranty
SUBJECT OF THE WARRANTY: the warranty is applied to the product and to
those parts which are marked with the serial number or any other identification
number used by MC elettronica;
DURATION OF THE WARRANTY: MC elettronica guarantees the Dorado MX3
KIT and its accessories for a period of 1 year from the date of manufacture
(printed on the identification label on the back of the Monitor).
The warranty covers the product and any repairs carried out within the agreed
terms.
This warranty does not apply in the event of:
accidental damage;
improper use;
changes which have not been agreed upon, improper installation (or set-
up);
damage caused when a equipment not manufactured by MC elettronica,
which is mechanically or electrically connected to our instruments, breaks
or does not function properly;
force majeure events (lightning, floods, fire or other causes which do not
depend on MC elettronica).
Repairs under warranty, which must be carried out in the laboratories of our
authorised centres, are entirely free of charge provided the equipment is
directly transported to said laboratories or sent carriage free. Transport costs
and ensuing risks are entirely borne by the Customer.
The above-mentioned warranty is valid unless otherwise agreed between MC
elettronica and the Customer.
!
Warning
MC elettronica declines any liability for damages or direct or indirect
costs caused by improper use or inability of the Customer to use the
equipment separately and/or together with other equipment.
1.3 Service
Service is available in all countries where the equipment is officially supplied by MC
elettronica (during and after the warranty period).
Any kind of operation to be performed on the Dorado MX3 KIT must be carried out
in accordance with the instructions provided in this manual or as agreed with MC
elettronica.
If not, the relative terms of the warranty might become null and void.
Instructions for use
Dorado MX3 kit
7
2. General description
The Dorado MX3 kit is a system designed for application on pneumatic precision
seed drills, the main functions of which are:
Check of the sowing distance and seed life for each row (max 12 rows);
the data for sowing distance and seed life is represented in numeric
format (value) and in analogue format (histograms)
Audible and visual alarms in the event of sowing that does not comply or
the absence of fertiliser
Calculation of the processed area; a total counter and a partial counter are
available.
There are also other functions available such as:
Display of RPM fan and visual and audible alarms (RPMmax and RPMmin
programmable)
Display of the depression related to the sowing system
The connection architecture of the Dorado MX3 kit is of modular and self-
configuring type; up to a maximum of 12 seed sensors can be controlled, to which 2
additional inputs for other sensors are added (feed-rate, RPM fan, vacuum gauge).
Each seeding ECU can handle 12 seed sensor inputs; a configuration connector
has been provided to connect its accessory. Each seeding ECU can be connected
indifferently to each wiring harness and the KIT will automatically recognise the
configuration. The diagram on the next page shows the main configurations (for
different configurations, contact Elettronica's Technical Department).
Instructions for use
Dorado MX3 kit
8
3. System installation
Figure 1. 3.5” Virtual Terminal dimensions
Instructions for use
Dorado MX3 kit
9
Figure 2. Seeding ECU dimensions code 10CEN-0009
Exclusions ECU dimensions code 10CEN-0010
Instructions for use
Dorado MX3 kit
10
3.1 Electrical connections
Inhaltsverzeichnis
