McCue FlexCore Guardrail Bedienungsanleitung
FlexCore Guardrail | Page 1 of 9
mccue.com
McCue Corporation
Peabody, Massachusetts, USA
+1 (800) 800 8503
McCue UK & Europe
Milton Keynes, United Kingdom
+44 (0)1908 365 511
McCue Asia
迈客(厦门)有限公司
Xiamen, Fujian, China
+86-592-2200790
FlexCore Guardrail
?
Questions
INSTALLATION INSTRUCTIONS
Tools Required
Components
Masonry Drill Bit
5/8˝ [16mm]
1˝ [25mm]
MarkerTape
Measure
15/16˝ Socket
& Extension
End Post Kit
GR-K-END
Core Kit
GR-K-COR
Lower Rail
GR-C-EXT
Mid Post Kit
GR-K-MID
Top Rail
GR-C-RAL
Template
GR-C-TMP
Rotary
Hammer
Drill with
7/32˝Hex Bit
Chalk
Line
7/32˝
Hex Key
Corded
Drill
FlexCore Guardrail | Page 2 of 9
Center
1" [25mm] DrillBit
Flange Hole Mark
1" [25mm] DrillBit
Flange Hole Mark
5/8" [16mm] DrillBit
Anchor Hole Mark
Anchor Hole Mark
5/8" [16mm] DrillBit
Alignment Marks
6.00in
[152mm]
Center to Flange
1.50in
[38mm]
Center to Anchor
Template Instructions
Modular Product
Use the included template to accurately mark hole locations for drilling. Steps that require the template will be labeled
the template icon.
This is a modular Guardrail System and each installation requires it's own custom layout. Please read
entire installation instructions before beginning your installation. If you require additional information,
please contact McCue Customer Care for assistance.
Template
Use template
for this step
FlexCore Guardrail | Page 3 of 9
C
e
n
t
e
r
h
o
l
e
to
c
e
n
t
er
h
ole
TOP VIEW
END POST TOP VIEW
5/8" Diameter
Anchor Hole
↓
5.5˝ [140mm]
1" Diameter
Flange Hole
↓
3˝ [75mm]
5/8" Diameter
Anchor Hole
↓
5.5˝ [140mm]
5/8" Diameter
Anchor Hole
↓
5.5˝ [140mm]
1" Diameter
Flange Hole
↓
3˝ [75mm]
5/8" Diameter
Anchor Hole
↓
5.5˝ [140mm]
1" Diameter
Flange Hole
↓
3˝ [75mm]
MID POST TOP VIEW
120in
3048mm
3.00in
[75mm]
1 in
[25mm]
5.5in
[140mm]
5/8 in
[16mm]
1
3
2
!
Attention: Make sure
the barrier hole and
flange markings line
up properly
+Chalk Line
+Rotary Hammer
with 1˝ & 5/8˝ Drill Bits
+Template &
Tape Measure
Attention: If section is less than 10' center
to center, see cutting instructions
Template
Use template
for this step
FlexCore Guardrail | Page 4 of 9
5/8 Anchor
Washer
Damper
Core
Flange
Aluminum Pin
!
Attention:
Start thread by
hand. Do not
cross thread!
Drill Optional.
+Impact Driver
with 15/16˝ Socket
+7/32˝
Hex Key
4
6
5
7
FlexCore Guardrail | Page 5 of 9
120in
3048mm
!
End Post:
Go to step 14
Mid Post:
Continue to next step
Attention: If rails are not
at the desired length, see
cutting instructions
8
9
+Template &
Tape Measure
Template
Use template
for this step
FlexCore Guardrail | Page 6 of 9
1" Diameter
Flange Hole
↓3˝ [75mm]
1" Diameter
Flange Hole
↓3˝ [75mm]
5/8" Diameter
Anchor Hole
↓5.5˝ [140mm]
5/8" Diameter
Anchor Hole
↓5.5˝ [140mm]
MID POST TOP VIEW
1.50in
[38mm]
1.50in
[38mm]
6 in
[152 mm]
6 in
[152 mm]
10
11
+Rotary Hammer
with 1˝ & 5/8˝
Drill Bits
FlexCore Guardrail | Page 7 of 9
5/8 Anchor
Washer
Damper
Core
12
13
+Impact Driver
with 15/16˝ Socket
!
Attention: Repeat
steps 9-13 until
last post
+7/32˝
Hex Key
FlexCore Guardrail | Page 8 of 9
14
15
+7/32˝
Hex Key
FlexCore Guardrail | Page 9 of 9
16
17
Installation instructions are provided for guidance only. The seller assumes no liability regarding improper
installation or misapplication of its products. It is the installer’s responsibility to check for proper installation
and, if in doubt, contact McCue Customer Care for assistance. ©2017 McCue Corporation. Jun 2017.
+7/32˝
Hex Key
FlexCore Guardrail
EXTRUSION CUTTING INSTRUCTIONS
Tools RequiredComponents
MarkerTape
Measure
Saw 1˝ Step Bit
Lower Rail
GR-C-EXT
Top Ra il
GR-C-RAL
Template
GR-C-TMP
Corded
Drill
Chalk
Line
mccue.com
McCue Corporation
Peabody, Massachusetts, USA
+1 (800) 800 8503
McCue UK & Europe
Milton Keynes, United Kingdom
+44 (0)1908 365 511
McCue Asia
迈客(厦门)有限公司
Xiamen, Fujian, China
+86-592-2200790
?
Questions
Inhaltsverzeichnis
Andere McCue Sicherheitssensor Handbücher
