MCE Technologies Xcaret Pro Bedienungsanleitung

Xcarét Pro

Expansion Bay

Hard Drive Kit

Installation Guide

http://www.mcetech.com

MCE Xcarét Pro Expansion Bay Hard Drive Kit 1

Introduction

Thank you for purchasing an MCE Xcarét Pro Expansion Bay

Hard Drive Kit! We are sure that your new device will enrich your

PowerBook computing experience. If at any time you are unsure

about or are having difficulty with the installation or use of your

new product, you may request assistance by calling 1-800-500-0622

or by sending an email to [email protected].

The MCE Xcarét Pro Expansion Bay Hard Drive Kit is a compact,

completely mobile storage solution for use in the right-side expan-

sion bay of your MacintoshPowerBook.

In order to get the most out of your new product, please read the

next several sections of this user’s guide on the use and care of the

MCE Xcarét Pro Expansion Bay Drive Kit.

The installation procedure involved with the Kit is a delicate

process and, if not performed properly, could cause damage to your

hard drive or PowerBook. MCE strongly recommends that the

installation be performed by a trained technician. These installa-

tion instructions are given for those who understand these risks and

are confident in their technical skills. If performed carefully and

patiently, these instructions will guide you step by step through a

successful installation of your new hard drive enclosure and/or

hard drive.

Note: If you are installing your PowerBook's original

internal hard drive into the MCE Xcarét Pro Expansion Bay

Drive Kit and have Password Protection enabled on the

drive or any volume on it, you must disable Password

Protection before removing the drive from your

PowerBook.

MCE Xcarét Pro Expansion Bay Hard Drive Kit

Preparing to Install

List of Items

The Xcarét Pro Expansion Bay Hard Drive Kit comes semi-

assembled. To prepare for the installation of a hard drive into the

Kit, one must remove the Kit cover from the base by carefully

lifting it up and out until the four locking clips are clear.

Check the contents of the package to ensure that all required

components are present:

a. (1) Black Kit Top

b. (1) Gray Kit Base

c. (1) Silver Internal Hard Drive Bracket

d. (1) Drive Connector with attached LED

e. (4) Dark Flat Head Screws

f. (4) Silver Bevel Head Screws

g. (1) MCE Mini Philips/Standard Screwdriver

You must supply a 2.5” IDE hard drive that is 12.7mm or shorter in

height and a little bit of patience to perform the installation.

e, f

screw holes

MCE Xcarét Pro Expansion Bay Hard Drive Kit 3

Installation

Step 1: Place the Xcarét Pro Kit

and hard drive on a dry, flat

surface.

Step 2: Carefully lift the Drive

Connector out of its slot and lay

it aside the Kit Base. DO NOT

pull on the LED wires attached

to the Drive Connector, as this may cause permanent damage! If

the LED slips out of its front-panel slot as far as it will go until it is

roughly flush with the front panel of the Kit Base.

Step 3: Carefully lift the Silver Internal Hard Drive Bracket and

the bag of screws from out of the Kit Base, being careful not to

snag the LED wires. Remember the orientation of the Drive

Bracket relative to Kit Base for reinstallation purposes.

Step 4: With the hard drive’s

label facing upward, carefully

place the hard drive into the

Drive Bracket, lining up the

side-mounted screw holes of the

hard drive with the holes on the

sides of the Bracket.

Note: The ends of the drive

should be flush with the ends of the Drive

Bracket. If the drive extends beyond the edges

of the Bracket, it is facing backwards and you must turn

the drive 180 degrees within the bracket. Hint: The hard

drive’s connector pins go on the side of the bracket oppo-

site the stamped series of numbers on the inside of the

bracket.

Drive Connector

MCE Xcarét Pro Expansion Bay Hard Drive Kit

Step 5: To secure the hard

drive to the Drive Bracket,

screw the four silver bevel-

headed screws into the sides of

the bracket/drive assembly.

Step 6: Carefully attach

the Drive Connector to the

hard drive as shown here.

Looking from above the

hard drive, note that the

two left-most columns of

pins (four pins total) are

not connected to the Drive

Connector. Do not place a

jumper on the unconnected

pins.

Step 7: Gently lay the hard drive with bracket onto the four

rubberized mounting posts in the Kit Base.

Step 8: Secure the Drive Bracket to the Kit Base by screwing four

flat-headed screws into the mounting posts of the Kit Base.

Note: Do not overtighten the screws onto the mounting

posts, as this may nullify the shock-dampening effect of the

rubberized ends of the posts.

non-connected pins

MCE Xcarét Pro Expansion Bay Hard Drive Kit 5

Caution: Be extremely careful in carrying out the next

step as they involve manipulating the delicate bronze-

colored ribbon of the Drive Connector, which, if damaged,

cannot be replaced.

Step 9: Slowly but firmly

slide the Drive Connector into

its slot in the Kit Base. Push

the Connector all the way

down so that the two teeth at

the bottom of the connector

bracket are completely seated

in their slots in the Kit Base.

Step 10: Carefully arrange the

LED wires so they do not cover

or obstruct the two slots on the

side of the Kit Base in which

they are situated.

(bottom of Kit Base)

Teeth seated

in slots

Keep area

around slots

clear

MCE Xcarét Pro Expansion Bay Hard Drive Kit

Step 11: Next, place the black Kit Top onto the Kit Base. Notice

the two alignment grooves located on the inside rear of the Kit

Top. This is where the top of

the green IC board and the

black plastic bracket of the

Drive Connector must be fitted

in order to ensure proper

alignment of the Kit Top. You

may have to gently push the

Drive Connector in to allow

the alignment grooves of the

Kit Top to properly catch and

secure the top of the green IC

board and bracket.

Step 12: Orient the Kit Top

such that the bottom of its label

is closest to the front of the Kit

Base. Pinch the two rear

locking tabs of the Kit Top and

partially slide them into their

slots in the inner sides of the Kit

Base. Next, pinch the other

two locking tabs and partially

slide them into their slots in the inner sides of the Kit Base.

Step 13: Once the Kit Top is

properly aligned with the Drive

Connector and the Kit Base,

secure the two halves together.

Lock the four locking tabs into

their respective slots by press-

ing down firmly on the Kit Top

just above the tabs.

alignment

grooves

locking tabs

➠

➡

MCE Xcarét Pro Expansion Bay Hard Drive Kit 7

Note: Be sure that all four locking tabs are securely seated

in their respective slots. You should hear a click when the

tab has locked into place in its slot.

Congratulations on completing the installation of your MCE

Xcarét Pro Expansion Bay Hard Drive Kit. Please refer to the

User’s Guide for information on operation and maintenance.

(bottom of Kit Base)

seated

locking tabs

MCE, the MCE logo and Xcarét Pro are trademarks of Mac Compo-

nents Engineered.

Apple, theApple logo, Mac, the MacOS logo, Macintosh, and Pow-

erBook, are registered trademarks of Apple Computer, Inc.

Products and company names are trademarks of their respective com-

panies, and are mentioned for informational purposes only and con-

stitute neither an endorsement nor a recommendation.

Every effort has been made to ensure that the information in this

manual is accurate. All errors including photographic, printing,

typographical, and clerical are subject to correction. Information

in this document is subject to change without notice and does not

represent a commitment on the part of Mac Components Engi-

neered.

Mac Components Engineered

Irvine, California, USA

Sales: (800)500-0622; [email protected]

Technical Support: (949)458-0800; [email protected]

http://www.mcetech.com

Rev. 011003

Andere Handbücher für Xcaret Pro

Inhaltsverzeichnis

Andere MCE Technologies Lagerung Handbücher

MCE Technologies

MCE Technologies Transport Pro Bedienungsanleitung

MCE Technologies

MCE Technologies Desktop Internal DVD-R/RW and CD-R/RW Drive Bedienungsanleitung

MCE Technologies

MCE Technologies Xcaret Pro Bedienungsanleitung

MCE Technologies

MCE Technologies Xcaret Pro Bedienungsanleitung

MCE Technologies

MCE Technologies Xcaret Pro-99 Bedienungsanleitung

MCE Technologies

MCE Technologies OptiBay Bedienungsanleitung

MCE Technologies

MCE Technologies POWERBOOK G4 Bedienungsanleitung

MCE Technologies

MCE Technologies Optibay series Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung