McQuay CC10C Bedienungsanleitung

1-1

English

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using yourairconditioner, please read this instruction manual carefully and keep it for future reference.

INSTALLATION MANUAL

CEILING CONCEALED SPLIT TYPE AIR CONDITIONER

MODEL

COOLING UNIT

CC10C / ACC10C / MCC010C

SL10B / ALC10B / MLC010B

CC15C / ACC15C / MCC015C

SL15B / ALC15B / MLC015B

CC20C / ACC20C / MCC020C

SL20B / ALC20B / MLC020B

CC25C / ACC25C / MCC025C

SL25B / ALC25B / MLC025B

CC30C / ACC30C / MCC030C

SL30C / ALC30C / MLC030C

CC40C / ACC40C / MCC040C

SL40C / ALC40C / MLC040C

CC50C / ACC50C / MCC050C

SL50C / ALC50C / MLC050C

CC60C / ACC60C / MCC060C

SL60C / ALC60C / MLC060C

HEAT PUMP

CC10CR /ACC10CR / MCC010CR

SL10BR / ALC10BR / MLC010BR

CC15CR /ACC15CR / MCC015CR

SL15BR / ALC15BR / MLC015BR

CC20CR /ACC20CR / MCC020CR

SL20BR / ALC20BR / MLC020BR

CC25CR /ACC25CR / MCC025CR

SL25BR / ALC25BR / MLC025BR

CC30CR /ACC30CR / MCC030CR

SL30CR /ALC30CR / MLC030CR

CC40CR /ACC40CR / MCC040CR

SL40CR /ALC40CR / MLC040CR

CC50CR /ACC50CR / MCC050CR

SL50CR /ALC50CR / MLC050CR

CC60CR /ACC60CR / MCC060CR

SL60CR /ALC60CR / MLC060CR

Part No.: 08019011545 IM-CCC-0700-1

CCC-0700 (01~16) ENG* 2/1/01, 10:41 AM1

1-2

Before installing the air conditioner unit, please read the following safety precautions carefully.

SAFETY PRECAUTIONS

!Warning

• Installation and maintenance should be performed by qualified persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with the national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard due to insulation failure.

• All electrical wiring must not touch the refrigerant piping, compressor and any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before installing or servicing the unit.

IMPORTANT

DO NOT INSTALL OR USE THEAIR CONDITIONER UNIT INA LAUNDRY ROOM.

CONTENTS

!Caution

Please take note on the following important points when installing.

• Do not install the unit where leakage of flammable gas may occur.

If gas leaks and accumulates at the surrounding of the unit, it may cause fire ignition.

• Ensure that the drainage piping is connected properly.

If the drainage piping is not connected properly, it may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged. Overcharge will cause over-current or damage to the compressor.

• Ensure that the unit panel is covered back after service or installation.

Unsecured panel will cause unit to operate noisily.

- Safety Precautions page 2

- Installation Diagram page 3

- Outline and Dimensions page 3

- Installation Of The Indoor Unit page 5

- Installation Of The Outdoor Unit page 6

- Refrigerant Piping page 7

- Electrical Connection page 8

- Purging The Refrigerant Piping page 12

- Additional Charge page 13

- Overall Checking page 14

- Standard Operating Condition page 14

- Auto Random Re-Start Function page 15

- Service And Maintenance page 15

- Trouble Shooting page 16

CCC-0700 (01~16) ENG* 2/1/01, 10:41 AM2

1-3

English

INSTALLATION DIAGRAM

INDOOR UNIT

AIR DISCHARGE NOZZLE

AIR INTAKE

REFRIGERANT PIPING

AIR INTAKE

OUTDOOR UNIT

OUTLINE AND DIMENSIONS

Indoor Unit

CC A B C D E F G H I J K L

10 C/CR 31 741 702 662 10 765 72 261 411 349 225 261

15 C/CR 31 881 842 802 10 905 72 261 411 349 225 261

20 C/CR 31 1041 1002 962 10 1065 72 261 411 349 225 261

25 C/CR 31 1176 1137 1097 10 1200 72 261 411 349 225 261

All dimensions are in mm

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM3

1-4

Indoor Unit (CC series)

(F) (F)

(E) (E)

(A)

(B)

(C)

(D)

Outdoor Unit (SL series)

MODEL A B C D E F G H J K L M N P Q R

10B/10BR 740 494 270 266 233 474 52 60 54 166 92 348 318 129 482 68.5

15B/15BR 740 494 270 266 233 474 52 60 54 166 92 348 318 129 482 68.5

20B/20BR 840 646 330 297 309 626 46 90 64 177 106 408 378 124 492 78.5

25B/25BR 840 646 330 297 309 626 46 90 64 177 106 408 378 124 492 78.5

2.5

64.5

CC A B C D E F

30C/30CR 939.0 999.0 378.0 541.0 408.5 359.0

40C/40CR 1055.0 1115.0 378.0 541.0 466.5 359.0

50C/50CR 1309.0 1369.0 378.0 541.0 593.5 359.0

60C/60CR 1509.0 1569.0 378.0 541.0 693.5 359.0

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM4

1-5

English

Outdoor Unit (SLC series)

SL A B C D E F G H J K L M N P

30C/40C/50C/60C 1030 850 400 390 414 827 72 196 91 488 448 141.5 746.5 82

SUCTION

LIQUID

Sharp edges and coil surfaces are potential locations which may cause injury

hazards. Avoid from being in contact with these places.

!Caution

INSTALLATION OF THE INDOOR UNIT

The indoor unit must be installed such that there is no short

circuit of the cool discharge. Respect the installation clear-

ance (see drawing C). Do not put the indoor unit where there

is direct sunlight on unit. The location is suitable for piping

and drainage and it must be have a large distance between a

door and unit.

CEILING CONCEALED MOUNTING

– Use the hanger supplied with the unit.

– Make sure that the wall is sufficiently strong to withstand

the weight.

Center distance of axle (see drawing below)

Provide clearance for servicing ease and optimal air flow as

shown in the diagram.

CC A L

10 C/CR 741 225

15 C/CR 881 225

20 C/CR 1041 225

25 C/CR 1176 225

30 C/CR 956 266

40 C/CR 1076 266

50 C/CR 1326 266

60 C/CR 1526 266

10.0

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM5

1-6

The location must be well-ventilated, so that the unit can

draw in and distribute plenty of air thus lowering the

temperature.

A place capable of bearing the weight of the outdoor unit as

well as isolating noise and vibration.

A place protected from the direct sunlight. Use an

awning for protection if necessary. Note:- If the obstacle is higher than 2m or if there is any

obstruction at the upper part of the unit allow more

space than indicated in the table above.

The installation location must not be susceptible to highly

concentrated dust, oil, salt or sulfide gas.

Outdoor unit SL series Clearance

RETURN AIR

OBSTACLE

SERVICE

ACCESS

DISCHARGE

AIR

INSTALLATION OF THE OUTDOOR UNIT

The outdoor unit must be installed such that there is no short

circuit of the air discharge air or obstruction to smooth air

flow. Respect the installation clearance show on the table.

Select the coolest possible place where intake air should

notbehigherthan theoutside temperature(maximum 45°C).

Ensure that there are no obstruction of air flow into or out

of the unit. Remove obstacles which block air intake or

discharge.

RETURN AIR

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM6

1-7

English

REFRIGERANT PIPING

MAXIMUM PIPE LENGTH AND MAXIMUM

NUMBER OF BENDS

When the pipe length becomes too long, both the capacity

and reliability drop. As the number of bends increases,

system piping resistance to the refrigerant flow increases,

thus lowering the cooling capacity. As a result, compressor

reliability will be affected. Always choose the

shortest path and follow the recommendation as tabulated

below:

PIPING WORKS AND FLARING TECHNIQUE

Do not use contaminated or damaged copper tubing. If any

piping, evaporator or condenser had been exposed or had

been opened for 15 seconds or more, vacuum the system.

Generally, do not remove plastic, rubber plugs and brass

nuts from the valves, fittings, tubings and coils until it is

ready for connection.

If any brazing work is required, ensure that the nitrogen gas

is passed through piping and joints while the brazing work

is being done. This will eliminate soot formation on the

inside walls of the copper tubings.

Cut the pipe stage by stage, advancing the blade of pipe

cutter slowly. Extra force and deep cut will cause more

distortion of pipe and therefore extra burr.

Remove burrs from cut edges of pipes with a remover as

shown in Fig. R. This will avoid unevenness on the flare

faceswhich willcause gasleak. Hold thepipe ontop position

and burr remover at lower position to prevent metal chips

from entering the pipe.

Insert the flare nuts mounted on the connection parts of both

indoor and outdoor unit, into the copper pipes.

The exact length of pipe protruding from the face of the

flare die is determined by the flaring tool.

Fix the pipe firmly on the flare die. Match the centers of

both the flare die and the flaring punch, and tighten flaring

punch fully.

1/4t

CUTTING COPPER TUBE

Fig. R

Model 10 15 20 25

Data

Maximum Length (m)

7101515

Maximum Elevation (m)

5588

Maximum No. of Bends (m)

10 10 10 10

20 m

MAX. PIPING LENGTH

MAX. ELEVATION HEIGHT

20 m

MAX. PIPING LENGTH

MAX. ELEVATION HEIGHT

REMOVE BURR

COPPER TUBE

SWAGING BLOCK

Model 30 40 50 60

Data

Maximum Length (m)

20 20 20 20

Maximum Elevation (m)

10 10 10 10

Maximum No. of Bends (m)

10 10 10 8

20 m

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM7

1-8

Ø TUBE A (mm)

INCH mm Imperial Rigid

1/4" 6.35 1.3 0.7

3/8" 9.52 1.6 1.0

1/2" 12.70 1.9 1.3

5/8" 15.88 2.2 1.7

3/4" 19.05 2.5 2.0

SPANAR TORQUE WRENCH

INDOOR PIPING FLARE NUT

FLARED TUBE

FLARE JOINT

PIPE SIZE (mm/in) TORQUE (Nm)

6.35 (1/4) 18

9.53 (3/8) 42

12.7 (1/2) 55

15.88 (5/8) 65

19.05 (3/4) 78

PIPING CONNECTION TO THE UNITS

Align the center of the piping and sufficiently tighten the

flare nut with fingers.

Finally, tighten the flare nut with torque wrench

until the wrench clicks.

When tightening the flare nut with the torque wrench,

ensure that the direction for tightening follows the arrow on

the wrench.

The refrigerant pipe connection are insulated by polyure-

thane (ARMAFLEX type or similar).

!Caution

ELECTRICAL CONNECTION

(Cooling only units for series 10C~25C with wire remote control & PCB)

IMPORTANT: These values are for information only, they should be checked and selected to comply with the local and/or

national codes and regulations. They are also subjected to the type of installation and size of

conductors.

INDOOR UNIT CC 10C CC 15C CC 20C CC 25C

OUTDOOR UNIT SL 10B SL 15B SL 20B SL 25B

Voltage range 220V – 240V /1Ph /50Hz + !

Recommended fuse A 610 16 20

Power Supply Cable size mm21.5 1.5 2.5 2.5

Number of conductors 33 3 3

Interconnection Cable size mm21.5 1.5 2.5 2.5

Number of conductors 33 3 3

Ensure the color of wires of the outdoor unit and the terminal markings are same to

the indoors respectively.

The electrical power must be provided with protection

devices (circuit breaker or fuse) with double pole

separation system (phase + neutral) with minimum

contact gap of 3mm.

TERMINAL STRIP

INDOOR UNIT

INTERCONNECTION

CABLE

TERMINAL STRIP

OUTDOOR UNIT

Cooling only units for series 10C~25C with wire remote control & PCB

COMP

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM8

1-9

English

(Heat pump units for Heat pump series 10CR~25CR with wire remote control & PCB)

IMPORTANT: These values are for information only, they should be checked and selected to comply with the local and/or

national codes and regulations. They are also subjected to the type of installation and size of

conductors.

INDOOR UNIT CC 10CR CC 15CR CC 20CR CC 25CR

OUTDOOR UNIT SL 10BR SL 15BR SL 20BR SL 25BR

Voltage range 220V – 240V /1Ph/ 50Hz + !

Recommended fuse A 610 16 20

Power Supply Cable size mm21.5 1.5 2.5 2.5

Number of conductors 33 3 3

Interconnection Cable size mm21.5 1.5 2.5 2.5

Number of conductors 33 3 3

The electrical power must be provided with protection

devices (circuit breaker or fuse) with double pole

separation system (phase + neutral) with minimum

contact gap of 3mm.

TERMINAL STRIP

INDOOR UNIT

INTERCONNECTION

CABLE

TERMINAL STRIP

OUTDOOR UNIT

Heat pump units for Heat pump series 10CR~25CR with wire remote control & PCB

Indoor unit CC 30C

Outdoor unit SL 30C

Voltage range 220V – 240V/ 1Ph/ 50Hz + !

Recommended fuse A 25

Power Supply Cable size mm24

Number of conductors 3

Interconnection Cable size mm22.5

Number of conductors 7

IMPORTANT: These values are for information only, they should be checked and selected to comply with the local and/or

national codes and regulations. They are also subjected to the type of installation and size of

conductors used.

(Cooling only units for series 30C with wire remote control & PCB)

Cooling only units for series 30C with wire remote control & PCB

COMP

4WV

COMP

4WV

COMP

The electrical power must be provided with protection

devices (circuit breaker or fuse) with double pole

separation system (phase + neutral) with minimum

contact gap of 3mm.

TERMINAL STRIP

OUTDOOR UNIT

INTERCONNECTION

CABLE

TERMINAL STRIP

INDOOR UNIT

OUTDOOR COIL SENSOR

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM9

1-10

The electrical power must be provided with protection

devices (circuit breaker or fuse) with double pole

separation system (phase + neutral) with minimum

contact gap of 3mm.

TERMINAL STRIP

OUTDOOR UNIT

INTERCONNECTION

CABLE

TERMINAL STRIP

INDOOR UNIT

Heat pump units for Heat pump series 30CR with wire remote control & PCB

Indoor unit CC 30CR

Outdoor unit SL 30CR

Voltage range 220V – 240V /1Ph /50Hz + !

Recommended fuse A 25

Power Supply Cable size mm24

Number of conductors 3

Interconnection Cable size mm21.5

Number of conductors 7

IMPORTANT: These values are for information only, they should be checked and selected to comply with the local and/or

national codes and regulations. They are also subjected to the type of installation and size of

conductors used.

(Heat pump units for Heat pump series 30CR with wire remote control & PCB)

Indoor unit CC 40C CC 50C CC 60C

Outdoor unit SL 40C SL 50C SL 60C

Voltage range 380V– 415V/ 3Ph/ 50Hz +N + !

Recommended fuse A 15 20 20

Power Supply Cable size mm22.5 2.5 2.5

Number of conductors 44 4

Interconnection Cable size mm21.5 1.5 1.5

Number of conductors 55 5

IMPORTANT: These values are for information only, they should be checked and selected to comply with the local and/or

national codes and regulations. They are also subjected to the type of installation and size of

conductors used.

(Cooling only units for series 40C with wire remote control & PCB)

COMP

4WV

COMP

4WV

OUTDOOR COIL SENSOR

CCC-0700 (01~16) ENG* 2/1/01, 10:42 AM10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere McQuay Klimaanlage Handbücher

McQuay

McQuay MCW200 Bedienungsanleitung

McQuay

McQuay 5CKWS 10CR Bedienungsanleitung

McQuay

McQuay MWM-LW Bedienungsanleitung

McQuay

McQuay R08019031289A Bedienungsanleitung

McQuay

McQuay SWP Series Bedienungsanleitung

McQuay

McQuay 5CKY10C Bedienungsanleitung

McQuay

McQuay G Series Bedienungsanleitung

McQuay

McQuay MQS-24018-CFC216A Bedienungsanleitung

McQuay

McQuay RCM20D Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

McQuay

McQuay CK Series Bedienungsanleitung

McQuay

McQuay A Series Bedienungsanleitung

McQuay

McQuay seasoncon ALP-067A Bedienungsanleitung

McQuay

McQuay SWP 018 Bedienungsanleitung

McQuay

McQuay M5CKY28ER Bedienungsanleitung

McQuay

McQuay MQS-174018-CFC216A Bedienungsanleitung

McQuay

McQuay Type K Incremental Packaged Terminal Air... Bedienungsanleitung

McQuay

McQuay IM-CKA-0501 A Series Bedienungsanleitung

McQuay

McQuay PTAC 106018561 Bedienungsanleitung

McQuay

McQuay E Series Bedienungsanleitung

McQuay

McQuay M5MSY18BR Bedienungsanleitung

McQuay

McQuay MDS 80 Bedienungsanleitung

McQuay

McQuay SWP 018 Bedienungsanleitung

McQuay

McQuay MWM Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung