MDV KJR-120X1/TFBG-E Montageanleitung

Installation and

Owner’s Manual

WIRED REMOTE CONTROLLER

MODEL:KJR-120X1/TFBG-E

KJR-120X2/TFBG-E

IMPORTANT NOTE:

Please read this manual carefully

before installing or operating your

wired remote controller. Make sure to

save this manual for future reference.

This manual gives detailed description of the precautions

that should be brought to your attention during operation.

In order to ensure correct service of the wired controller

please read this manual carefully before using the unit.

For convenience of future reference, keep this manual

after reading it.

All the pictures in this manual are for explanation purpose

only. There may be slightly dierent from the wired remote

controller you purchased (depend on model). The actual

shape shall prevail.

1. Safety precaution

2. Installation accessory

3. Installation method

4. Specification

5. Feature and function of the wired controller

6. Name on the LCD of the wired controller

7. Name of button on the wired controller

8. Preparatory operation

9. Operation

10. Timer functions

11. Weekly Timer 1

12. Weekly Timer 2

13. Fault alarm handing

14.Technical indication and requirement

15.Queries and settings

..........................................................1

................................................... 2

........................................................4

..................................................................9

................10

.....................11

.......................12

.................................................13

.....................................................................14

.........................................................20

..........................................................23

..........................................................29

...................................................36

.........................36

..................................................37

Table of Contents

1. Safety precaution

Do not uninstall the unit randomly.

Random uninstalling may lead to abnormal operation,

heating or re of the air condition.

Please entrust the distributor or professionals to install the unit.

Installation by other persons may lead to imperfect installation,

electric shock or re.

Adhere to this installation manual.

Imporper installation may lead to electric shock or re.

Reinstallation must be performed by professionals.

•

NOTE

Do not install the unit in a place vulnerable to leakage of

ammable gases.Once ammable gases are leaked and left

around the wire controller, re may occure.

Do not operate with wet hands or let water enter the wire

controller. Otherwise, electric shock may occur.

•

The wiring should adapt to the wire controller current.

Otherwise, electric leakage or heating may occur and result in

re.

•

WARNING

1. Safety precaution

NOTE

The specied cables shall be applied in the wiring. No external

force may be applied to the terminal. Otherwise, wire cut and

heating may occur and result in re.

•

2. Installation accessory

Don’t install at the place where cover with heavy oil, vapor or sulfureted

gas, otherwise, this product would be deformed that would lead to

system malfunction.

Select the installation location

Preparation before installation

1. Please conrm that all the following parts you have been supply.

M3.9X25 (For Mounting on the Wall)

M4X25 (For Mounting on switch box)

No. Name Qty. Remarks

For Mounting on the Wall

Plastic screw bars

Screws

Wall plugs

For xing on switch box

Optional

Screws

Installation and owner’s manual

Wire controller

Battery

The connective wires group

Screw

M4X8(For Mounting the connective wire group)

Magnetic ring

Use the magnetic ring to hitch the connective cable of the wire controller.

2. Installation accessory

Precaution of installing the wire controller

1. This manual provides the installation method of wired

controller. Please refer to the wiring diagram of this installation

manual to connect the wire controller with indoor unit.

2. The wired controller works in low voltage loop circuit. Forbid

to directly contact the cable of high voltage above,like 115V,

220V,380V, and don’t wire this kind of wire in the

said loop; wiring clearance between congured tubes should

be at the range of 300~500mm or above.

3. The Shielded wire of the wired controller must be grounded

rmly.

4. Upon nish the wire controller connection, do not employed

tramegger to detect the insulation.

2. Prepare the following assemblies on the site.

Switch box

Wiring Tube(Insulating

Sleeve and Tightening

Screw)

Qty.(embeded

into wall)

No. Name Remarks

Specification

(only for reference)

3. Installation method

Fig 3-2

Fig 3-1

1.Wired remote controller structural dimensions

2.Remove the upper part of wired controller

Insert a slot screwdriver into the

slots in the lower part of the wired

controller (2 places), and remove

the upper part of the wire

controller. (Fig.3-2)

19mm84mm

46mm

60mm

44mm

120mm

120mm 20mm

Buckling

position Back cover

Straight head

screwdriver

Front cover

3. Installation method

Fig 3-3

Fig 3-4

For exposed mounting, fasten the back plate on the wall with

the 3 screws (M4×20) and plugs. (Fig.3-3)

Use two M4X25 screws to install the back cover on the 86

switch box, and use one M3.9X25 screw to x to the wall.

3. Fasten the back plate of the wired controller

Back plate

Screws (M4×20)

Screw hole xed on the wall,useone φ3.9X25mm

Screw hole installed on 86 switch box, use two M3.9X25mm

NOTE: The PCB is mounted in the upper part of the wired

controller. Be careful not to damage the board

with the slot screwdriver.

3. Installation method

Put the battery into the installationsite and make sure the

positive side of the battery is in accordance with the

positive side of installationsite.(See Fig.3-5)

Please set the time corrected on the rst time operation.

Batteries in the wire controller can time under power

failure which ensure the time keep right. When the power

restores, if the time displayed is not correct, it means the

battery is dead and replace the battery.

Fig 3-5

4. Battery installation

NOTE: Put on a at surface. Be careful not to distort the

back plate of the wire controller by overtightening the

mounting screws.

3. Installation method

Fig 3-6

5. Wire with the indoor unit

Fig 3-7

Putty

Trap

1 indoor unit

2 notch the part for the wiring to pass through with nippers, etc.

NOTE: DO NOT

allow water to enter

the remote control.

Use the trap and

putty to seal the

wires.

44mm

60mm

Wiring

hole

switch box

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MDV Fernbedienung Handbücher

MDV

MDV RG57A8/BGEF Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung