Meatest M505D Bedienungsanleitung

M505 (D) Process calibrator

Operation manual

MEATEST, s.r.o. Process Calibrator M505

1 version 7 Operation manual

Content

1INTRODUCTION ...............................................................................................................................2

2UNPACKING INSTRUCTIONS.......................................................................................................3

3INPUTS, OUTPUTS and KEYBOARD............................................................................................4

4GRAPHICS DISPLAY........................................................................................................................5

5DATALOGGER (Software Option) ..................................................................................................5

6FUNCTION SELECTION - CALIBRATOR...................................................................................6

7GRAPHICS..........................................................................................................................................8

7.1 GRAPHICS....................................................................................................................................8

7.2 TRANSIENTS................................................................................................................................8

8MENU STEPS......................................................................................................................................9

9ADDITIONAL FUNCTIONS in the MULTIMETER MODE .....................................................10

10 SOFTWARE - CALIBRATION ......................................................................................................10

10.1 CALIBRATION of CALIBRATOR OUTPUTS..........................................................................11

10.1.1 Calibration of Currents ........................................................................................................11

10.1.2 Calibration of Voltages.........................................................................................................11

10.1.3 Calibration of Resistances....................................................................................................12

10.2 CALIBRATION MULTIMETER .....................................................................................12

11 DATALOGGER ................................................................................................................................13

12 SOFTMANAGER M505W...............................................................................................................14

13 SPECIFICATION..............................................................................................................................18

13.1 CALIBRATOR .............................................................................................................................18

13.2 MULTIMETER............................................................................................................................19

Process Calibrator M505 (D) MEATEST, s.r.o.

Operation manual v7 2

1 Introduction

Current Calibrator 0/4 - 22mA, Source/Sink

Voltage Calibrator 0-25V

mV Outputs 0-27mV and 0-540 mV

DIN Thermocouples J, K, N, R, S, T, B, E

RTD Simulator Pt and Ni

Resistance Simulation to 3kOhm

Multimeter ±2V to ±200V DC and +100mA

Calibrates and Measures Simultaneously

Eight Memory slots for fast Transients

Graphics of Measurements

Steps, Ramps, direct value settings

Datalogger Function in M505 D model

M505 is a Calibrator-Multimeter for generation of Currents 0-22mA Sink or

Source und Voltages to 25VDC. External voltages ±2V, ±20V and ±200VDC

(firm ranges or auto ranging) and Currents to ±100mA can be measured

simultaneously and shown at the display.

Further Functions contain generation of calibration mV Signals, Thermo voltages of DIN Thermocouples and RTD

Resistors and simulation of true resistors.

mV voltages of 0-27mV or 0-540mV are mainly used for calibration of Strain Gauges, Transmitters and small

signal inputs with resolution of up to 0.001mV.

Thermocouples J, K, N, R, S, T, B, E are simulated. The temperature is entered with the keyboard and shown at the

display. The cold junction is compensated to the ambient temperature. It can also be switched-off.

RTD Thermometers can be simulated within the DIN temperature range. The temperature is entered with the

keyboard and shown at the display.

Ohm Source Resistance values up to 3kOhm are simulated. The resistance value is entered with the keyboard and

shown at the display.

Graphics and Memorising of measured signals is a standard function. The signals are continuously stored and

shown at the display as graphics. In apart of this eight memory slots for storing of fast signals -Transients- are

available. They can individually be stored and selectively recalled at the display.

Datalogger is an Option. The calibrating signals and the multimeter input are shown at the display and stored as

tables with date and time from internal RTC. They can be downloaded to the PC and edited under Windows and

Excel. A software program is available for Windows.

Process Calibrator M505 (D) MEATEST, s.r.o.

3 Operation manual v6

2 Unpacking Instructions

Remove the Packing List and verify that you have received all equipment, including the following:

- Model M505 Handheld Calibrator.

- Operation Manual M505.

If you have any questions about the shipment, please call the Meatest Customer Service.

Content of delivery

- Calibrator-Multimeter Model M505 (D)

- Charger 95-240VAC

- Two signal cables

- T/C plug K, U

- SoftManager for Windows

- Operation Manual and Calibration Certificate

NOTE

When you receive the shipment, inspect the container and equipment for signs of damage. Note

any evidence of rough handling in transit. Immediately report any damage to the Meatest customer

service, Phone +420 543 250 886 or Fax +420 543 250 890 and to the shipping agent.

The carrier will not honour damage claims unless all shipping material is saved for inspection. After

examining and removing contents, save packing material and carton in event the reshipment is

necessary.

Process Calibrator M505 (D) MEATEST, s.r.o.

Operation manual v7 4

3 Inputs, Outputs and keyboard

CALIBRATOR

Voltage and Current Outputs,

Resistance and RTD: + OUTPUT -

Thermocouples: Cu Terminals at the front

MULTIMETER

Voltage and Current Inputs: + INPUT -

CONTROLLER

The Functions of the Calibrator and the Multimeter are selected with the keyboard and supported by a

microcontroller. The factory settings and the calibrated points are stored in a nopn-volatile memory and remain

stored also when the instrument is switched off. The software calibration of all ranges is accessible in the

calibration menu and protected with a password. All ranges can be recalibrated via the keyboard if required.

The graphic display is divided into two windows. The upper window is shows the multimeter functions, the lower

window the calibrator. In programming mode the display shows the parameters. In graphics mode of operation the

display shows the stored input signals.

The Multimeter is always active and can be used independently from the calibrator. The ranges can be selected

with the keyboard. The current range is firm. The voltage ranges are firm 2V, 20V or 200VDC or can be set as

automatic range.

Minus Terminals of the Calibrator and the Multimeter are common.

1 Thermocouples Connector

2 Output Calibrator

3 Input Multimeter

4 LCD-Display

5 Main Keys

6 Cursor Keys

7 Memory Key

8 Recall Graphics

9 Datalogger

10 Selection of Calibrator Output Mode

11 Function Keys

12 Charger Jack

13 USB

Process Calibrator M505 (D) MEATEST, s.r.o.

5 Operation manual v6

4 Graphics display

The LCD Display is divided into two parts. The upper part is for the multimeter functions, the lower part for the

calibrator. The bargraph in the middle is the analogical representation of the measured input signals. The left side

shows various symbols:

Symbols in the upper display part

AUTO Automatic Voltage Range or firm measuring range

200V Measure Ranges 2V, 20V, 200V, 100mA

INP The display shows the input signal.

Symbols in the lower display part

RMP Automatic Ramp of the calibrator signal

SUP The battery is being charged

60% Battery voltage in %. Do not run the instrument when the battery shows 0%. Charge only with the

enclosed original charger.

5 Datalogger (Software Option)

The generated signal and the measured signal are stored in a table format. The date and the time are added. The

stored data can be downloaded via the USB to a PC. A Soft Manager supports the data transfer to a Windows PC.

Two Set Points LEVEL LOW and LEVEL HIGH and two Intervals INTERVAL 1 and INTERVAL 2 will be

selected. If the measured signal is between the both Set Points LEVEL LOW and LEVEL HIGH, the data will be

stored with INTERVAL 1. The INTERVAL 2 stores the date when the input signal is outside the Set Points. The

both Intervals can be selected from 2 sec. to 24 hours.

With the key LOGG is the function Datalogger active. The key MENU and the two cursor keys permit the

parameter selection. With OK the setting will be stored.

MULTIMETER measured input voltage in

automatic range.

CALIBRATOR generates 12.000mA. The Battery

has 70% of capacity.

LOGGER OFF Datalogger OFF

LOGGER ON Data are stored

MEMORY ERASE Erase the memory

INTERVAL 1: < 2 Sek. … 24 Std.

INTERVAL 2: < 2 Sek. … 24 Std.

LEVEL LOW: free settable

LEVEL HIGH: free settable

Process Calibrator M505 (D) MEATEST, s.r.o.

Operation manual v7 6

6 Function selection –calibrator

The calibrator function is selectable with the keys. The output values can be set in steps, ramps or free values.

The output function will be selected with OUT. Vertical cursor keys select the required function:

Current Source 0 - 22mA

Current Sink 0 - 22mA

Voltage Output 0 - 25V

Voltage Output 0 - 560mV

Voltage Output 0 - 28mV

Resistance Output 45 - 3000 Ohm

RTD Outputs Pt-100, Pt-200, Pt-500,

Pt-1000, Ni 1000

Simulation of Thermocouples

B, J, K, N, R, S, T

OK confirms the selection. The selected function remains memorised also when the power is switched-off.

Process Calibrator M505 (D) MEATEST, s.r.o.

7 Operation manual v6

DIRECT VALUE ENTRY

When the key NUM is pressed, the display shows the previous value with flashing digit. This digit can be set from

the keyboard. The flashing digit will be positioned automatically. It can also be positioned with the horizontal

cursors.

RAMPS

The key RAMP activates the Ramp generation. The values at the display increment in steps selected in the Menu.

The display shows the symbol RMP.

By pressing the key RAMP again, the ramp generation will stop.

Ramp Steps selection in MENU

Press MENU. The step can be selected from firmly pre-programmed values with the vertical cursors. Confirm with

OK.

RAMP STEPS

With keys RAMP or STEP the display will increment in steps selected in the MENU.

Selection of Steps in the MENU

Press the key MENU. Use the vertical cursors to select the Step from pre-programmed values. Confirm with OK.

Selection of individual Steps

The range and the steps can be set in two memory slots FN.1 and FN.2.

Press MENU and select RAMP SELECT. With the key MENU and vertical cursors select the range and the steps.

Confirm with OK.

Example: Current Output 0 - 22mA

DN STEP: Display decrementing

UP STEP: Display incrementing

Individual Ramp Step scan be selected und stored

in FN.1 and FN.2.

Example: Current Output 0 - 22mA

DN STEP: Display decrementing

UP STEP: Display incrementing

Process Calibrator M505 (D) MEATEST, s.r.o.

Operation manual v7 8

7 Graphics

For fast diagnostics of external signals measured by the multimeter the graphics representation can be displayed.

Two modes of operation are available:

- GRAPHICS the running measurement is automatically stored in 128 points (FI-FO)

- TRANSIENTS Eight individual memory slots are assigned for fast signals –Transients.

The sampling time and the Trigger level are selectable.

The Memory module for the Graphics and the Transients are common. By recalling the Transients, the Graphics

will be erased.

7.1 GRAPHICS

The key GRAPH opens the graphic presentation.

Graphics deactivated - GRAPH OFF. The graphics can be activated with vertical cursors - GRAPH ON.

The latest stored signal will be displayed when OK is pressed.

7.2 TRANSIENTS

Fast signals at the multimeter input can be stored. Eight individual memory slots TRANSIENT NO.1 …

TRANSIENT NO.8 are available. The sampling rate is 1ms. Each transient contains 256 Point and can be time

limited from 0.25 to 300 seconds. The Trigger level is programmable from <10% to >90%.

With the key MENU the Transients can be stored or recalled at the display. The selection is done with the vertical

cursors.

The parameters will be selected with the key MENU:

Stored Transient 1 is shown at the display

Transient 1 deleted

The key MENU and vertical cursors select

the time

The key MENU and vertical cursors select

the Trigger level

The graphics at the display

Start of Transient 1

memorizing

0.25 … 300 sec.

<10% … >90%

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Meatest Prüfgeräte Handbücher

Meatest

Meatest 9010 Bedienungsanleitung

Meatest

Meatest M-142 Installationshandbuch

Meatest

Meatest M631 Bedienungsanleitung

Meatest

Meatest M133C Bedienungsanleitung

Meatest

Meatest M525 Bedienungsanleitung

Meatest

Meatest M-140 Bedienungsanleitung

Meatest

Meatest MC641 Bedienungsanleitung

Meatest

Meatest M133C Bedienungsanleitung

Meatest

Meatest 9010+ Bedienungsanleitung

Meatest

Meatest M143 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung