MEE H6D Bedienungsanleitung
H6D BLUETOOTH
WIRELESS HEADSET
WITH DOCK AND BOOM MICROPHONE
POWERED BY
H6D BLUETOOTH
WIRELESS HEADSET
Package Contents
Micro-USB
charging cable
Charging
dock
H6D Bluetooth
wireless headset
Package Overview
Volume down button
Status indicator light
Micro-USB charging port
Charging dock connector
Multifunction button
Volume up button
Microphone
A
B
C
D
E
F
G
H
I
J
Headset dock connector
Power indicator light
Micro-USB power port
A B C D E F G
H I J
Headset
Charging Dock
Charging
Connect the dock to any
powered USB port using
the included micro-USB
cable. The red power
indicator light on the
charging dock will light up.
Place headset on
charging dock.
Low battery is indicated by a flashing red status indicator
light and “battery low” voice notification every five minutes.
Charging time is approximately 2 hours. The red status
indicator light on the headset will turn blue once fully
charged.
Option 1:
Using Charging Dock
PORT
USB
Directly connect the H6D headset to any powered USB port
using the included micro-USB cable.
Option 2: Using USB Cable
PORT
USB
Pairing
Press and hold the Multifunction button for about 8 seconds
until the status indicator light flashes red and blue.
Note: The headset will enter pairing mode automatically on
first use or after being reset.
Pairing (Continued)
Open the Bluetooth menu on the device you wish to pair
(usually located in Settings->Bluetooth). If needed, select
“search for devices”, “pair new device”, or “refresh.”
Select “MEE audio H6” and allow pairing to complete. Use
“0000” if a pin is required.
Note: It is only necessary to pair your headset once with
each device.
AT&T LTE 12:26 PM 95%
Bluetooth
Settings
Searching...
Bluetooth
Devices
AT&T LTE 12:26 PM 95%
Bluetooth
Settings
MEE audio H6
Bluetooth
The H6D stores previously paired devices and reconnects
automatically with the last paired Bluetooth device when
powered on.
If the headset does not connect automatically, open the
Bluetooth menu on your device and select “MEE audio H6”
from the Bluetooth device list.
Reconnecting to Paired Devices
Wearing
Adjust the boom mic for
use on the left or right ear.
Adjust the headband to a
comfortable length.
Basic Functionality & Controls
*Not all devices support this functionality. For more information, refer to the
user manual for your device.
**To start playing music, open a music app on your device and start
playback.
Volume Down / Previous Track button
- Decrease Volume
- Previous Track
(during media playback**)
[TAP]
[HOLD 2 sec]
- Increase Volume
- Next Track
(during media playback**)
Multifunction button
[TAP]
[HOLD 2 sec]
[TAP]
[HOLD 2 sec]
[TAP twice]
[TAP]
- Answer Incoming Call
- Reject Incoming Call
- Hang Up
- Siri®/ Voice Command /
Voice Dialing*
- Redial*
- Play / Pause
(during media playback**)
[TAP]
[HOLD 2 sec]
[HOLD 2 sec]
[HOLD 5 sec]
- Power On
- Power Off
Volume Up / Skip Track button
Select “MEE audio H6” and allow pairing to complete. Use
“0000” if a pin is required.
Note: It is only necessary to pair your headset once with
each device.
Multipoint Functionality
Multipoint allows two Bluetooth devices to be connected to
the headset simultaneously.
To use two Bluetooth devices with the H6D, first pair each
one by following the pairing procedure described in the
Pairing section, then power the headset off.
When powered on again, the headset will be able to connect
to both devices. If one of the devices does not connect
automatically, select “MEE audio H6” from the Bluetooth
menu of the device.
To switch between the two connected devices, pause audio
playback on the active device and start audio playback on
the other connected device. It may take up to 30 seconds for
the audio to switch.
Incoming calls will always take precedence over media. The
H6D will automatically activate the connected device that
has an incoming call.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere MEE Headset Handbücher
