Meech 954v2 Bedienungsanleitung
Model 954v2
Operating
Manual
Ionising Airgun
Products shown in this document may be covered by one or more patents, patents applied for
and/or registered designs and/or trade marks. For further information please refer to our Head
Oce or visit www.meech.com.
© Meech Static Eliminators Ltd., 26.10.17
Contents
Introduction 3
Unpacking and Inspection 4
General Notes On Operation 4
Installation 5
Compressed Air 5
Electrical connection 5
Performance 5
Technical Specication 6
Maintenance 7
Fault Finding 9
Repairs and Warranty 11
CE Approval 11
Health and Safety 11
3
Introduction
The Meech 954v2 Ionising Air Gun is an upgraded model, that provides exceptional
performance when neutralising static charges and removing dust and contamination
on a wide range of industrial processes. The 954v2 has many improvements over its
predecessors due to innovations in engineering. These include the use of additive
manufacturing that make the 954v2 60% faster and 40% lighter than the previous
version.
4
Unpacking and Inspection
The Model 954v2 Ionising Air Gun has been carefully packed at the factory in a
container designed to protect it from accidental damage. Nevertheless, we recommend
careful examination of the carton and contents for any damage. If damage is evident,
do not destroy the carton or packing material and immediately notify the carrier of
a possible damage claim. Shipping claims must be made by the consignee to the
delivering carrier.
General Notes On Operation
The typical Meech ionised air gun installation consists of one or more guns connected
to a Meech power unit.
David.Hyde
14/04/2014
Drawn by:Date:
5 / 5
Sheet
Meech International
2 Network Point
Range Road, Witney
OX29 0YN, UK
Tel: +44 (0) 1993 706700
Fax: +44 (0) 1993 776977
email: [email protected]
web: www.meech.com
COPYRIGHT © MEECH STATIC ELIMINATORS
THIS DOCUMENT AND THE INFORMATION
THEREIN IS THE PROPERTY OF THE MEECH
GROUP AND SHOULD NOT BE COPIE D IN WHOLE
OR PART OR USED FOR MANUFACTURE OR
OTHERWISE DISCLOSED WITHOUT THE PRIOR
WRITTEN CONSENT OF MEECH INTERNATIONAL
MATERIAL:
FINISH:
TOLERANCE UNLESS
OTHE RWISE SP ECIFIED
Machined Wo rk Metric ±0.1mm
Unmachined F abrications ±1mm
Angular ±0°30'
PROJECTION
DIMENSIONS IN MM
DO NOT SCALE
TITLE:
DRAWING No:
REVISION:
SHEET:
Various
1:4
STATUS: Production
CRITICAL TO FUNCTION
(CTF) DIMENSIONS AS
MARKED
The power unit provides the high voltage AC supply that is required for eective
ionisation. The ionising airgun is connected to the power unit by a tough, exible
conduit and high voltage cable. The high voltage is fed to a sharp titanium emitter pin
via a safety resistor that renders the pin safe to touch. A corona is generated at the tip
of the pin, ionising the surrounding airow.
The ionised airow will neutralise the target surface, releasing the surface
contamination and allowing it to be blown o.
5
Installation
Compressed Air
The compressed air supply must be clean and dry. Meech recommend the use of a
5 micron coalescing lter. Water or oil in the air will damage this product. The Meech
guarantee does not cover this. The use of a pressure regulator will allow the pressure
to the gun to be set to the correct level for the application.
A typical operating pressure for the 954v2 is 3.5 bar / 50 psi. The gives a good
balance of ionisation and cleaning performance. However, depending on the
application, higher or lower pressures may be required. Air Connection to the 954v2 is
via a standard 6mm push-t tting.
Electrical connection
Electrical connection is to a Meech Model 904 7kV power supply. Please refer to the
904 Power Supply operating instructions to ensure that your ionising gun is correctly
and safely connected to its power supply. A copy of this can be downloaded from
www.meech.com
Performance
5000V to 500V decay tests were carried out at 150mm distance in accordance with
ESD Association standard S3.1
Pressure PSI Noise dBA Decay +5000 to <100V
30
40
50
60
70
80
74
76
79
80
80
81
0.8
0.4
0.4
0.3
0.3
0.3
6
Technical Specication
Model 954v2
Max pressure : 6.8 Bar/100PSI
Recommended pressure : 3.4 Bar/ 50PSI
Operating voltage : 7kV from Meech 904 power unit
Max Temperature : 85°C.
Construction : Gun handles – cast aluminium
Nozzle body - Nylon
Weight : 300 g approx
Cable : 3 metres of H.T. cable supplied as
standard, longer lengths can be specied
when ordered.
7
Maintenance
Ionisers require periodic cleaning. During normal operation, dirt may build-up on
the emitter pin. The rate of this contamination will depend on the cleanliness of the
compressed air supply. The contamination will cause a reduction in performance.
Typically, weekly inspection/cleaning is sucient.
The emitter and the inside of the nozzles can usually be cleaned using a cotton bud.
If the emitter has become very dirty, it may need to be removed before cleaning.
To remove the emitter, insert a 3mm nut spinner into the end of the nozzle and
unscrew it counter-clockwise.
The nut spinner Meech uses is a BAHCO (BE-7803)
Once removed, the pin can be cleaned. A toothbrush is deal for this.
8
The exterior of the nozzle can be wiped down with a damp cloth.
Should you have any additional questions regarding the maintenance of Meech
equipment please contact Meech International directly or your local Meech distributor.
Inhaltsverzeichnis
Andere Meech Elektrowerkzeuge Handbücher
