Outputs up
to 8 or 16
users
Optional connection of a
DVB-T antenna for terrestrial
television or FM radio
HH
HH
VH
VH
HL
HL
VL
VL
standard
multiswitch
Quattro LNB
Outputs up
to 8 or 16
users
Outputs up
to 8 or 16
users
Outputs up
to 8 or 16
users
Optional connection of a
DVB-T antenna for terrestrial
television or FM radio
HH
HHHHHH HHHHHH
VH
VHVHVH VHVHVH
HL
HLHLHL HLHLHL
VL
VLVLVL VLVLVL
standard
multiswitch
or
cascadable
multiswitch
with termina-
ting resistor
cascadable
multiswitch
cascadable
multiswitch
Quattro LNB
Outputs up
to 8 or 16
users
HH
HH
VH
VH
HL
HL
VL
VL
standard
multiswitch
A B
Quattro LNB
HH
HH
VH
VH
HL
HL
VL
VL
Quattro LNB
ASTRA HOTBIRD
Multiswitch Installation Instruction
Safety instructions
Please check before using the coaxial cables for possible short circuits, as it could
otherwise lead to a defect on the multiswitch. The location should be dry and
protected from moisture. Make sure that the multiswitch is not exposed to direct
sunlight, is not applied near to heat sources and adequate ventilation is ensured.
To avoid short circuit, do not plug in the AC adapter to power before all coaxial
cables are connected.
Connection
Mount the LNB to the provided holder of the dish and connect it to the multis-
witch. The outputs of the Quattro LNB must be connected to the corresponding
inputs of the multiswitch. The names may vary from manufacturer to manufac-
turer (eg„HH“ or „High/H“, ...). Free connections (set-top box outputs) should be
provided with terminating resistors to avoid possible interference. If multiple
satellites are operated, every LNB must be connected to the respective group of
the multiswitch. This means that LNB 1 must connected with all 4 levels in group
A of the multiswitch. LNB 2 in group B (see Sample 2).
IMPORTANT:
Unused LNB inputs and outputs of the cascadable multiswitches must NOT be
assigned with a terminating resistor (power pass)!
Excerpt from the Declaration of Conformity
Hereby declare the company Megasat Werke GmbH that the following devices is
in compliance with the essential requirements and other relevant provisions of Di-
rective 2014/30/EU and 2014/35/EU and Radio Equipment Directive 2014/53/EU:
• Multiswitch 5/8 (Art.-No. 0600150)
• Multiswitch 5/12 (Art.-No. 0600205)
• Multiswitch 5/16 (Art.-No. 0600152)
• Multiswitch 9/8 (Art.-No. 0600151)
• Multiswitch 9/16 (Art.-No. 0600153)
• Multiswitch 17/8 (Art.-No. 0600154)
• Multiswitch 17/16 (Art.-No. 0600155)
• Multiswitch 5/8 C (Art.-No. 0600189)
• Multiswitch 5/16 C (Art.-No. 0600192)
• Multiswitch 9/8 C (Art.-No. 0600190)
• Multiswitch 9/16 C (Art.-No. 0600193)
• Multiswitch 17/8 C (Art.-No. 0600191)
• Multiswitch 17/16 C (Art.-No. 0600194)
The Declaration of Conformity for these products are located at the company:
Megasat Werke GmbH, Industriestraße 4a, D-97618 Niederlauer
The declaration of conformity can be our homepage:
www.megasat.tv/support/downloads
Sample 1: 1 satellite with standard multiswitch
Sample 2: 2 satellites with standard multiswitch
Sample 3: 1 satellite with cascade multiswitch
Version 1.1 (March 2019)
