MEI CASHFLOW 8000 Series Benutzerhandbuch

Part Number 79xxxxxxx Rev G1

START

UP GUIDE

CASHFLOW

8000 S

eries

Change Manager

Page 2 of 10

INSTALLATION

Preparing for Installation

♦Turn OFF all power to the vending machine.

♦To ensure that the CF8000 performance is not

affected, visually check the vending machine is

upright, both from the front and side.

♦Before mounting the CF8000 to the vending

machine, check the operating voltage of the vending

machine matches that stated on the CF8000 label.

Installing the CF8000 to the machine

The CF8000 is mounted onto the vending machine by hanging it onto three studs

located on the vending machine. To do this you will need to open the

discriminator assembly and line up the mounting keyholes of the CF8000 with the

vending machine studs.

♦Press the yellow button at the top of the CF8000 and gently lift and pull the

discriminator assembly forward. Once open, the mounting keyholes will be

made visible.

♦To securely fix the CF8000 in place, partly unscrew the three machine studs.

♦Line up the three mounting keyholes of the CF8000 with the studs and hang it

in place ensuring that the CF8000 is sitting flat against the machine back

plate.

Label

Page 3 of 10

♦Tighten all three studs and return the discriminator back to its normal position.

Alignment Checks

Once the CF8000 has been securely fitted to the vending machine, check reject

lever operation and coin chute alignment. Do this without any power applied to

the machine.

Cable Connection

The CF8000 may be fitted with more than one cable,

these may be intended for TX-RX communications,

drive an external display or to extract audit data.

Once all relevant cables are connected and before

closing the machine door, tuck any unused cables away

tidily ensuring that none are trapped between the reject

lever mechanism and the vending machine door. You

can now switch ON the power to the vending machine.

4mm

Lid

Lever

Reject

Button

Check there is a minimum 4mm gap between

the machines reject lever mechanism and the

CF8000 reject button.

Press the machine lever a couple of times and

ensure the lid of the discriminator opens and

closes correctly.

Check machine coin chute alignment by inserting

two of each coin denomination through the coin

entry slot of the machine.

Ensure that the inserted coins fall freely into the

CF8000 and exit out into the machines cash

return cup.

Product

Dimensions

H: 371mm

W: 138mm

D: 80mm

Page 4 of 10

KEYPAD FUNCTIONS

On the front of the CashFlow

8000 there is a user interface keypad. The keypad

has six function buttons and a large LCD display.

This keypad allows you to dispense coins from the five-tube dispenser, access &

navigate through the configuration menus and monitor the status of the CF8000.

1 USB Socket Audit, Configuration, Service

2 to Dispense coins & navigate through menus

3 Irda Port Infra-red Audit

4 Display (LCD) Menu information & warning display

5 ‘Mode’ Button Access service & setup menus

6 Service Connector Mini USB link to PC

The blue keys (marked A to E) have two functions.

When the CF8000 is in idle mode, pressing a blue button on its own will dispense

a coin from that tube. When you press and hold the blue button for approx. 4

seconds, this activates auto dispense (latch dispensing of coins) until the tube is

empty of coins. If however, the yellow (mode) button is pressed, the blue buttons

are then used for navigation through the CF8000 service mode and setup mode

menus.

Service Mode: gives access to the most frequently used product configuration

options.

(See Service Mode Options - Page 6)

Setup Mode: gives access to general product configuration options that are

required when setting up your CF8000.

(See Setup Mode Menus - Page 7)

4 5 6

2 3

Page 5 of 10

GETTING STARTED

At power up, the CF8000 will run a self test, where the CF8000 motor will sound.

The LCD display briefly shows its software revision and as there are no coins in

the tube cassette, the display will show a “Low Tubes” message requesting that

the coin tubes be filled to a predefined level (

refer to the floating coin tubes section

Once the CF8000 has enough coins in the tubes, the LCD display will show the

coin totals (in currency value) stored in the tubes.

Note: MEI recommends that a small number of coins (e.g. 5 of each) be inserted

in each tube prior to leaving the machine.

Floating the Coin Tubes

There are two ways to float the CF8000 tubes with coins.

1) Manually fill each tube by inserting coins into the tubes.

2) Use the Service Mode and insert coins through the discriminator.

Filling Tubes Manually

1. Remove the tube cassette from the CF8000.

2. Insert required number of coins into relevant storage tubes.

3. Re-fit tube cassette back on to the CF8000.

The CF8000 will now begin an automatic tube calibration measurement where a

clicking sound will be heard, this is normal. Once calibration is complete the

display will show a total currency value of the coins inserted. If a tube is left

empty the display will show a tube low message for the particular tube.

Fill Tube using Service Mode

1. Press the Yellow ‘Mode’ button once.

2. Press ‘A’ button and start inserting coins through the discriminator.

3. The display will show the number of coins that are required for each tube.

(the displayed count will decrement as coins are inserted)

4. Press ‘A’ button to exit float mode.

CF8000 Menu Structure

Setup Mode

There are two ways to access the Setup Mode menus.

1. Press and hold the ‘Mode’ button for 2 seconds.

2. Press the ‘Mode’ button once and select the ‘Setup’ option by pressing

button ‘E’. (This method requires a pass code. When asked for this, press

buttons ‘A’‘B’‘C’).

Page 6 of 10

Service Mode Options (Quick Menu Codes)

This list shows the most commonly used service modes.

Press Following

Button Sequence Description /

Action

Float coin tubes / (Insert coins then press ‘Mode’

button)

Clear accumulated credit – (Not MDB) and clear

‘Clean Me’ message.

Float Teach sets float levels to current coin tube

levels.

[Not available in Auto Float mode]

Inhibit a coin / (Insert a coin and then press the reject

lever)

Enable a coin / (Insert a coin and then press ‘Mode’

button)

View coin details / (press to scroll up)

(press to scroll down)

View channel set / (press to exit view)

Teach vend price / (Insert coins to the value of

the price and then press the price line button on

the machine to set it)

(When finished press the button)

[This feature is only available on Executive products]

Custom tube cassette teach /

(Enter coin, select position then press )

Select predefined tube cassette / (enter code on

cassette label & press ‘Mode’ button)

Page 7 of 10

Setup Mode Menus

Menu Starts from Here

Prices

Language

Float Options

Change Mgmt

Machine Options

Coin Config

Cashless Config

General

Error Log

Test

Audit Config

Bank Note Config

EXAMPLE: - How to set the language

1. Press the ‘Mode’ button once

2. Press button ‘E’ to select ‘Setup’

3. Enter pass code, Press ‘A’‘B’‘C’

4. Press button ‘D

’ to scroll up the menu

an until the display shows Language

5. Press ‘Select’ then ‘Edit’

6. Use button ‘D’ or ‘E’ to scroll to the

required language

7. Select ‘OK’

8. Select ‘Back’ and ‘Back’ again to

save your setting and exit

Messages Only if Messages available

Press button ‘D’ - Scrolls Up the menus

Press button ‘E’ – Scrolls Down the menus

Menu Option Selected

Page 8 of 10

Alert Messages

An Alert message on the display allows you to pinpoint a fault that may have

occurred on one of the modules of the changegiver. These types of fault can be

rectified at the machine and can be for example caused by; a coin jam, dirt built

up or the cassette has been removed etc.

Alert Message Changegiver Maintenance

Discriminator error

Accept gate error

Separator module sensor error

Tube cassette error

Dispenser module error

Predefined Cassettes

The CF8000 has stored in memory a selection of predefined tube cassettes that

provide different payout options. These additional payout options can be

activated by entering the correct “Cassette Code” on the keypad.

The “Cassette Code” can be found on the front label of the cassette.

To select a predefined cassette, press the ‘Mode’ button then ‘D’ followed by the

button code. Finally select ‘Accept’ from the menu to confirm and save.

Note: You must have the correct cassette payout fitted and empty of coins as

the CF8000 will need to calibrate the new cassette.

Page 9 of 10

Machine Interface

Manufacturer Machine Audit Capability

Klix Outlook Dex Kit Needed

Colibri

No Audit Available - S/w update

Venecia

Jack option available

Zenith

Pre 2000 Printer only

Sfera

>2006 S/W files needed (+4K Board)

Astro

<2006 Jack looms only ?

Snack

Brio

Rondo

Kikko

Canto

Necta

Sambo

- All Eprom variants - no Audit

Brela

Mistral

Azkoyen

Palma

BVM

Bianchi LEI

- New Machines Dex & DDCMP

Rhea Sagoma

Sielaff - Need Audit Capable Display PCB

FAS - No Audit option

- Dex (machines ?) Jack Fitted or 4 Pin

Dixie 5800/5594

Royal - Dex

Crane - PCN Connector J36

Vendo VDI Jack

VUE Jack

Page 10 of 10

SAFETY

National & International Standards Conformance

CashFlow

8000 Series products operate at Safety Extra Low Voltage Level

(SELV) as defined in IEC335/EN60335 ‘Safety of Household and Similar

Appliances’. They may be designed into equipment complying with

IEC335/EN60335 or IEC950/EN60950 ‘Safety of Information Technology

Equipment’.

CashFlow

8000 Series products are of Class 3 construction.

Rated Operating Voltage

The operating voltage of a CashFlow

8000 Series is stated on the label attached

to the product. It must not be used with any power source other than that

indicated.

Operating Temperature

Ambient Operating Temperature: (-15°C) to 70°C

Dangerous Environments

The CashFlow

8000 Series must not be operated in the presence of flammable

gasses, fumes or water. The CF8000 is not suitable for use in areas where there

could be direct contact with water jets.

Routine Maintenance

Maintenance should be performed by properly trained service technician.

Clean with mild soap and damp cloth. Allow to dry completely prior to re-powering

the CF8000.

Product Disposal

Do not dispose of any part of a CashFlow

8000 Series by incineration.

CashFlow

8000 Series Start

Up Guide

Revision G1

Publication Date: September 2010

Internet: http://www.meigroup.com

MEI

, CashFlow

and the MEI device are registered

trademarks.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MEI Geldzähler und Münzsortierer Handbücher

MEI

MEI CASHFLOW 9520 Leitfaden

MEI

MEI Cashflow 690 series Referenzhandbuch

MEI

MEI Cashflow 9500 Bedienungsanleitung

MEI

MEI Economy Series Bedienungsanleitung

MEI

MEI CASHFLOW 952 Series Bedienungsanleitung

MEI

MEI Cashf low SC83 Bedienungsanleitung

MEI

MEI Cashflow 690 series Referenzhandbuch

MEI

MEI CASHFLOW 9510 Bedienungsanleitung

MEI

MEI EC6000 Handbuch

MEI

MEI TRC Series Bedienungsanleitung

MEI

MEI CashFlow REFERENCE Series Bedienungsanleitung

MEI

MEI CASHFLOW 7000 Series Benutzerhandbuch

MEI

MEI SCR Bedienungsanleitung

MEI

MEI CASHFLOW 7000 Series Benutzerhandbuch

MEI

MEI cashflow VN2700R Bedienungsanleitung

Beliebte Geldzähler und Münzsortierer Handbücher anderer Marken

Coinco

Coinco Guardian 6000 Montage- und Bedienungsanleitung

Hyundai MIB

Hyundai MIB SB-2000 Bedienungsanleitung

Royal Sovereign

Royal Sovereign RBC-2100 Bedienungsanleitung

Peradon

Peradon DCT Bedienungsanleitung

Beckmann

Beckmann EMS-58 Bedienungsanleitung

Safescan

Safescan 1450 Bedienungsanleitung

Hamilton Manufacturing Corporation

Hamilton Manufacturing Corporation Audit Pro 2000 Kurzanleitung

Alberici

Alberici EP-1P0S Bedienungsanleitung

PRO Intellect Technology

PRO Intellect Technology PRO CS-80E Bedienungsanleitung

Alberici

Alberici AL66 FG modifiable ccTalk Bedienungsanleitung

Inepro

Inepro Multi Connectivity Box Bedienungsanleitung

Standard Change-Makers

Standard Change-Makers MC Series Bedienungsanleitung

Safescan

Safescan 1250 SGD Bedienungsanleitung

Alberici

Alberici Hammer Two Bedienungsanleitung

Money Control

Money Control SR3 Bedienungsanleitung

Ribao

Ribao CS-600A Bedienungsanleitung

Coinco

Coinco Guardian GLX Series Original Betriebsanleitung

Azkoyen

Azkoyen t3 hopper Bedienungsanleitung