Meinberg IMS-PIO180 Bedienungsanleitung

MANUAL

IMS-PIO180 Setup Guide

Hot-Plug Module

6th May 2020

Meinberg Funkuhren GmbH & Co. KG

Table of Contents

1 Imprint 1

2 Introduction 2

3 Safety Instructions for hot pluggable Modules 3

3.1 Additional Safety Hints ........................................... 4

3.2 Cabling ..................................................... 4

3.3 Prevention of ESD Damage ......................................... 4

4 Front Connectors IMS-PIO180 6

4.1 Status LEDs .................................................. 7

4.2 In- Outputs (PPS or 10 MHz) ....................................... 7

5 Before you start 8

5.1 Scope of Delivery ............................................... 8

5.2 Disposal of Packaging Materials ...................................... 9

5.3 Pre-selection (PPS, 10 MHz) ........................................ 9

6 System Installation 10

6.1 Important Hints for hot-pluggable IMS Modules ............................. 10

6.2 Replacement or Installation of a Hot-pluggable IMS Module ..................... 11

6.3 Connecting the System ........................................... 12

7 Conﬁguration of the IMS-PIO180 13

7.1 Menu IO Conﬁg ................................................ 13

8 Status Monitoring of the IMS-PIO180 14

8.1 The SyncMon ................................................. 14

9 RoHS and WEEE 16

Date: 6th May 2020 IMS-PIO180 Setup Guide

1 Imprint

Meinberg Funkuhren GmbH & Co. KG

Lange Wand 9, 31812 Bad Pyrmont / Germany

Phone: + 49 (0) 52 81 / 93 09 - 0

Fax: + 49 (0) 52 81 / 93 09 - 230

Internet: https://www.meinbergglobal.com

Mail: [email protected]

Date: 06.05.2020

IMS-PIO180 Setup Guide Date: 6th May 2020 1

2 Introduction

This Setup Guide is a systematically structured guideline which supports you during the set-up of your Mein-

berg product.

The four I/O ports of the IMS module PIO180 (PIO=Programmable Input/Output) can be used as inputs as

well as outputs. Primarily, the module was developed to perform measurements of e.g. PPS signals of external

systems against the internal reference time.

Functionality

The oﬀset from the external reference against the high-precision time of the internal oscillator is measured

with an accuracy of 5ns (measurement resolution 1ns). With the SyncMon these measurements can be logged

and analyzed. If the ports of the PIO180 are to be used as outputs, the signal direction can be set to output in

the LTOS web GUI (see chapter 7).

The LTOS7 manual provides a complete description of all conﬁgurations and status monitoring options of

your Meinberg product.

Download link: https://www.meinbergglobal.com/download/docs/manuals/english/ltos_7-00.pdf

Compatibility

The PIO180 is an IMS module which is compatible with all systems of the IMS family. It can also be used on

any slot (MRI, ESI, I/O). For example, it is possible to build up a central measurement system with a LANTIME

M3000, which can log and analyze the accuracy of up to 40 PPS signals of external systems with the help of

the SyncMon, which acts as a central measurement system with a PIO180 module.

2 Date: 6th May 2020 IMS-PIO180 Setup Guide

3 Safety Instructions for hot pluggable Modules

Check before every maintenance work on the system:

•If a data backup is required?

•Is a backup required, verify the data recovery which is done by this backup.

•Make sure to avoid any static discharge while working - use a grounding cable and/or antistatic gloves

during installation and removal of hot pluggable components.

•If you are replacing a hot pluggable power supply, unplug the power cable prior to removing the module

from the case.

•Never open a power supply. In power supplies dangerous voltages can still remain even after disconnection

from the power supply. Always send power supplies back to the manufacturer for maintenance.

Exchange of hot-swap components

•Ensure that components which will be replaced during operation, always be treated with the utmost care.

Avoid contact with live components.

•Electrostatic discharge can damage electronic components. For this reason, ensure protection against

electrostatic discharges by wearing anti-static shoes while working with the system.

•Take care when removing and installing the hot-plug modules. Always work with the utmost caution.

Touch the modules only at the edges.

•Place the module out of the box or after removal from the system with the component side to the top on

a grounded and static-free surface.

•Storage of an IMS module must be done in a dry place.

•Installation or removal from hot-swap components only by authorized personnel!

IMS-PIO180 Setup Guide Date: 6th May 2020 3

3.1 Additional Safety Hints

This manual contains important information for the installation and operation of this device as well as for your

safety. Make sure to read carefully before installing and commissioning the device.

Certain operating conditions may require the observance of additional safety regulations not covered by this

manual. Nonobservance of this manual will lead to a signiﬁcant abatement of the security provided by this

device. Security of the facility where this product is integrated lies in the responsibility of the installer.

The device must be used only for purpose named in this manual, any other use especially opteration above the

limits speciﬁed in this document is considered as improper use.

Keep all documents provided with the device for later reference.

This manual is exclusively for qualiﬁed electricians or by a qualiﬁed electrician trained personnel who are

familiar with the applicable national standards and speciﬁcations, in particular for the construction of high

voltage devices.

3.2 Cabling

WARNING!

DANGER TO LIFE BY ELECTRICAL SHOCK! NO LIVE WORKING!

Wiring or any other work done the connectors particularly when connectors are opened may never be carried out

when the installation is energized. All connectors must be covered to prevent from accidental contact to life parts.

ALWAYS ENSURE A PROPER INSTALLATION!

3.3 Prevention of ESD Damage

ATTENTION!

The designation ESD (Electrostatic Sensitive Devices) refers to measures which are used

to protect electrostatically endangered components from electrostatic discharge and thus

to prevent destruction. Systems and assemblies with electrostatically endangered components

usually have the following characteristics:

Indicator for assemblies with electrostatic endangered components

The following measures protect electrostatically endangered components from destruction:

Prepare removal and installation of assemblies

Unload yourself (for example, by touching a grounded object) before touching assemblies.

Ensure that you wear a grounding strap on the wrist when working with such assemblies, which

you attach to an unpainted, non-conductive metal part of the system.

4 Date: 6th May 2020 IMS-PIO180 Setup Guide

3 Safety Instructions for hot pluggable Modules

Use only tools and devices that are free from static electricity.

Transporting Assemblies

Assemblies may only be touched at the edge. Do not touch any pins or conductors on assemblies.

Installing and Removing Assemblies

Do not touch persons who are not grounded while removing or installing components. This could

result in a loss of grounding protection from your electrostatic discharge.

Storing Assemblies

Always keep assemblies in ESD protective covers. These protective covers must be undamaged.

ESD protective covers, which are extremely wrinkled or even have holes, no longer protect against

electrostatic discharge.

ESD protective covers must not be low-resistance and metallically conductive if a lithium battery

is installed on the assembly.

IMS-PIO180 Setup Guide Date: 6th May 2020 5

4 Front Connectors IMS-PIO180

6 Date: 6th May 2020 IMS-PIO180 Setup Guide

4 Front Connectors IMS-PIO180

4.1 Status LEDs

Status Indicators

LED St: PIO status

LED In: Status of the backplane’s output signals

LED P: display for preset PPS

LED C: display for preset 10 MHz

Initialisation: LED St: blue until USB is conﬁgured

LED In - LED B: oﬀ until USB is

conﬁgured

USB is conﬁgured: LED St: blue

LED In:

0,5 sec. red -> 0,5 sec. yellow ->

0,5 sec. green -> 0,5 sec. oﬀ

Normal Operation: LED St. + LED In: green

LED P: green, if card is preset to PPS

LED C: green, if card is preset to 10 MHz

St In P C

4.2 In- Outputs (PPS or 10 MHz)

Technical Speciﬁcations:

Connections: 4 x BNC connectors, by software as

in- or outputs individually

switchable

Signal option: PPS or 10 MHz

(selectable via jumper)

Signal level: TTL

Impedance: 50 Ohm

Measuring accuracy: 5 ns (1 ns resolution)

IMS-PIO180 Setup Guide Date: 6th May 2020 7

Inhaltsverzeichnis

Andere Meinberg Steuereinheit Handbücher

Meinberg

Meinberg IMS-GNS181 Bedienungsanleitung

Meinberg

Meinberg IMS SCG180-U Bedienungsanleitung

Meinberg

Meinberg IMS-MRI Bedienungsanleitung

Meinberg

Meinberg IMS-LNE-GBE-SFP Bedienungsanleitung

Meinberg

Meinberg IMS-FDM Bedienungsanleitung

Meinberg

Meinberg IMS VSI180 Bedienungsanleitung

Meinberg

Meinberg IMS-TCR180 Bedienungsanleitung

Meinberg

Meinberg IMS-PZF180 Bedienungsanleitung

Meinberg

Meinberg IMS-GNS182 Bedienungsanleitung

Meinberg

Meinberg IMS-HPS-100 Bedienungsanleitung

Meinberg

Meinberg NUC80E Bedienungsanleitung

Meinberg

Meinberg IMS-ESI Bedienungsanleitung

Meinberg

Meinberg IMS-VSG181 Bedienungsanleitung

Meinberg

Meinberg IMS-REL1000 Bedienungsanleitung

Meinberg

Meinberg IMS BPE-3050 Bedienungsanleitung

Meinberg

Meinberg IMS-GPS180 Bedienungsanleitung

Meinberg

Meinberg IMS-GNS181-UC Bedienungsanleitung

Meinberg

Meinberg IMS-VSG181 Bedienungsanleitung

Meinberg

Meinberg IMS-LNE-GBE Bedienungsanleitung

Meinberg

Meinberg IMS-REL1000 Bedienungsanleitung

Meinberg

Meinberg IMS SCG180-B Bedienungsanleitung

Meinberg

Meinberg IMS-FDM Bedienungsanleitung

Meinberg

Meinberg IMS-VSI Bedienungsanleitung

Meinberg

Meinberg IMS-MRI Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung