Melitta MEMB1W Mill & Brew Bedienungsanleitung

USE AND CARE GUIDE FOR

MODELS MEMB1W, MEMB1B

AND MEMB1CAN

READ AND SAVE THESE INSTRUCTIONS

WARNING: A risk of fire and electrical shock exists in all

electrical appliances and may cause personal injury or death.

Please follow all safety instructions.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and injury

to persons, including the following:

• Read all instructions before using appliance.

• Do not touch hot surfaces. Use handle.

• Do not immerse cord, plug or coffeemaker base in water or other

liquid. See instructions for cleaning.

• This appliance is not for use by children.

• Close supervision is necessary when any appliance is used near

children.

• Unplug from outlet when not in use. Unplug and allow to cool

before attaching or removing parts and before cleaning the

appliance.

• Do not let cord hang over edge of table or counter or touch hot

surfaces.

• Do not place on or near a hot gas or electric burner or in a heated

oven.

• Do not use appliance except as indicated in these instructions.

• Decanter must never be used on a range top. Use only the

designated decanter for your coffeemaker.

• Do not set a hot decanter on a wet or cold surface.

• Do not use a cracked decanter or a decanter having a loose or

weakened handle.

• Do not clean decanter with abrasive cleaners, steel wool pads or

other abrasive material.

• Do not remove lid or covers during brewing cycle, scalding may

occur.

• Allow mill/brew basket to cool before removing it from appliance.

• To disconnect, press stop button, then remove plug from wall

outlet.

• Do not move entire unit when decanter contains hot liquid.

• Do not operate any damaged appliance. Do not operate with a

damaged cord or plug, or after the appliance malfunctions or has

been dropped or damaged in any manner. Return appliance to the

nearest authorized service center for examination, repair,

electrical or mechanical adjustment.

• Use accessory attachments only if recommended by

manufacturer.

• Be certain lids and covers are securely in place before operating

appliance.

• Do not use outdoors or while standing in a damp area.

• WARNING: Do not remove bottom cover. No user serviceable

parts inside. Repair must be done by authorized service

personnel only.

• The mill is intended for processing small quantities of coffee beans

only for immediate consumption. This appliance is not intended to

prepare large quantities of ground coffee at one time.

• WARNING: To prevent injury from hot overflow, replace decanter

within 20 seconds, if removed during brewing. Pour slowly when

full.

• Check mill/brew chamber for presence of foreign objects before

using.

• Blades are sharp. Handle carefully.

• Do not attempt to defeat the cover interlock mechanism.

• Avoid contacting moving parts.

• Do not open Mill/Brew assembly lid until blades stop and brewing

is complete.

SAVE THESE INSTRUCTIONS

THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY

CAUTION: A short power supply cord is provided to reduce the risk

of personal injury resulting from becoming entangled in or tripping

over a longer cord. Extension cords are available from local hardware

stores and may be used if care is exercised in their use. If an

extension cord is required, special care and caution is necessary.Also

the cord must be: (1) marked with an electrical rating of 125 V, and at

least 13 A, 1625 W, and (2) the cord must be arranged so that it will

not drape over the countertop or tabletop where it can be pulled on by

children or tripped over accidentally.

POLARIZED PLUG: This appliance has a polarized plug, (one blade

is wider than the other). As a safety feature to reduce the risk of

electrical shock, this plug is intended to fit in a polarized outlet only

one way. If the plug does not fit fully in the outlet, reverse the plug. If

it still does not fit, contact a qualified electrician. Do not attempt to

defeat this safety feature.

ELECTRIC POWER: If the electric circuit is overloaded with other

appliances, your appliance may not operate properly. It should be

operated on a separate electric circuit from other operating

appliances.

Safeguards (Continued)

TIME

HRMIN

SELECT

GRIND

COARSEFINE

ON/OFFMILL

TIME

HRMIN

SELECT

GRIND

COARSEFINE

ON/OFFMILL

FIGURE 1 FIGURE 2

FIGURE 3 MILL/BREW ASSEMBLY FIGURE 4

FIGURE 1

1. Reservoir Cover

2. Water Window

3. Pause and Pour

4. Decanter Lid

5. Decanter

6. Cord Storage

7. Warming Plate

8. Coffeemaker Base

9. Control Panel

10. LED Display

11. Lock Buttons

12. Mill and Brew Assembly

13. Mill/Brew Assembly Lock

14. Mill/Brew Assembly Lid

15. View Window

FIGURE 2

1. Mill/Brew Assembly Lid

2. Spreader Tube

3. Measuring Spoon

4. Motor Grinder Pin

5. Pause and Pour

6. Locking Buttons

FIGURE 3

1. Mill/Brew Basket

2. Maximum Fill Level

3. Blades

4. Pause and Pour

5. Lock Buttons

6. Basket Tabs

7. Mill/Brew Basket Lid

8. Mill/Brew Basket Tabs

Before Using Your Mill & Brew

Coffeemaker

CAUTION: UNPLUG FROM OUTLET

COFFEEMAKER: Clean the decanter and its lid, mill/brew basket

and its lid, and mill/brew assembly. See Care and Cleaning.

Fill the coffeemaker with the maximum amount of water and no

coffee and turn the unit ON. See Brewing. Unplug coffeemaker and

discard the water. Wait 10 minutes to allow heating elements to cool.

Repeat this process one more time.

CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEEMAKER

BASE IN WATER OR OTHER LIQUID.

CAUTION: BLADES ARE SHARP. DO NOT ATTEMPT TO

DISASSEMBLE MILL & BREW ASSEMBLY.

Setting the Clock

1. Set the clock for actual time of day. Press and hold “HR”button

for 2 seconds. The LED display will flash and unit will enter into

the clock-setting mode. Press “HR”and “MIN”buttons to set

correct time. Small dot in upper left corner of display signifies

A.M. No dot indicates P.M. The clock display will flash

5 times, then stop. The time is now set.

Brewing Instructions

CAUTION: DO NOT FILLMILL/BREW BASKET WITH MORE THAN

8 SPOONS OR 21⁄8OUNCES OF COFFEE BEANS. ARROW ON

BASKET INDICATES MAXIMUM CAPACITY. DO NOT FILL

MILL/BREW BASKET WITH MORE THAN 8 SPOONS OR 23⁄4

OUNCES OF GROUND COFFEE.

1. Plug into 120V-60 Hz outlet. You do not have to set clock or timer

to brew.

2. Fill decanter with cold water and pour desired number of cups

into water reservoir. Use markings on water window to gauge

level of water required to brew desired number of 5-ounce cups.

The number 10 at the top indicates maximum 10-cup yield.

Replace decanter on warming plate.

3. Open mill/brew assembly lid and grasp mill/brew basket tabs to

remove basket lid. Place 1 measuring spoon roasted whole bean

coffee in mill/brew basket per every two cups of coffee desired.

Replace lid. Make sure basket is firmly seated in assembly, lid on

basket is secured and lid to assembly is closed before

attempting to operate unit.

NOTE: You may substitute ground coffee for coffee beans by

turning off the mill. To do so, push the Mill button. The light will

come on. Place ground coffee into mill/brew basket. Use

approximately 1 tablespoon of grounds per cup of coffee.

4. You are now ready to initiate the automatic mill and brew process.

(If you wish to use the delay timer so you can program the

coffeemaker to mill and brew later, please read section entitled

“Programming the Timer”to make coffee later.

Programming the Mill

CAUTION: DO NOT OPEN UNTIL BLADES STOP AND BREWING

IS COMPLETE. CLEAN AND DRYALL PARTS AFTER EACH USE.

If you desire a medium grind, your machine is automatically preset to

“4”or medium grind; refer to step 2 below. If you wish to program a

finer or coarser grind, start with step 1.

1. To set the mill to grind your beans to the desired level of

coarseness, press SELECT button to select different coarseness

levels, 1-7. Seven levels of coarseness are available.

Coarseness is determined by length of time milled—the longer

the time, the finer the grind. Setting 1 will mill the beans for

15 seconds. Setting 7 will mill the beans for 40 seconds. For

medium grind, try setting 4 (if you do not select a setting, the unit

will automatically default to setting 4). Make sure mill light is off.

2. Press ON button to initiate the mill/brew process; the red ON

light will come on. Mill will start. After mill stops, unit will

automatically switch to brewing operation. To interrupt milling

or brewing, press OFF button. Red ON light will then turn off.

Do not attempt to lift mill/brew lid until operation has come to

a complete stop.

3. After brewing is complete, remove decanter from warming plate

and serve. Coffeemaker warming plate will cycle on and off to

maintain proper coffee temperature for one hour before it

automatically shuts off and the red ON light turns off.

4. Unplug and allow unit to cool for 10 minutes between cycles.

Allow to cool completely before attempting to clean.

Brewing Instructions (Continued)

NOTE:After unit is turned off or automatically shuts off after one

hour, mill coarseness setting will default to level 4 or medium

grind. Coarseness setting will also default to level 4 in the event

of power interruption.

Programming the Timer to

Make Coffee Later

You can program the timer to automatically mill and brew coffee up to

24 hours in advance.

1. Press and hold the TIME button for 2 seconds. The green TIME

light will come on and display will read 12:00. The unit is now in

the timer programming mode.

2. Press “HR”and “MIN”buttons to program start time. Small dot

in upper left corner signifies clock is programmed forA.M. No dot

in upper left corner means clock is programmed for P.M.

3. The timer display and LED light will flash 5 times to indicate that

timer is now set. Press and release the TIME button.

The green TIME light will come on.

NOTE: If unit is operated before programmed time, timer will

need to be reset. To do this, simply depress TIME button. LED

light will come on to indicate timer has been reset.

IMPORTANT: If programming timer to future start time, make

sure water tank has been filled and mill/brew basket contains the

correct amount of beans.

Care and Cleaning

CAUTION: ALWAYS UNPLUG UNIT BEFORE CLEANING AND

ALLOW TO COOL FOR 15 MINUTES BEFORE ATTEMPTING TO

CLEAN. NEVER USE SCOURING AGENTS. NEVER IMMERSE

MACHINE IN LIQUIDS. NEVER CLEAN MACHINE UNDER

RUNNING WATER.

Decalcification of Your Mill & Brew Coffeemaker

For best tasting coffee, and to promote longer use of your Mill & Brew,

follow the procedure for decalcification every month, or after 30 uses.

If you have hard water, you may notice a slowing of the brewing

process—an indication that you should decalcify more frequently.

Programming the Mill (Continued)

1. Press OFF button.

2. Unplug and allow to cool completely before cleaning.

3. Wash and dry all removable parts.

CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEEMAKER

UNIT IN WATER OR OTHER LIQUID.

CAUTION: BLADES ARE SHARP. HANDLE CAREFULLY.

4. Special cleaning of the coffeemaker is recommended at least

once a month, depending on frequency of use and quality of

water. Mineral deposits can form a coating in the coffeemaker.

This may cause an off flavor in the water and may lengthen

brewing time.

5. Fill the decanter with 1 cup of vinegar and add 3 cups cold water.

Pour into water reservoir.

6. Make sure mill/brew basket and assembly are securely in place

and lid is closed.

7. Place decanter on warming plate.

8. Press ON button.

9. Halfway through brewing, press the OFF button. Carefully

remove the decanter and place on a heat resistant surface. Wait

15 minutes and pour solution back into water reservoir.

10. Press ON button. Allow all solution to empty into decanter. After

dripping stops, press OFF button and discard solution.

11. Allow coffeemaker to cool 10 minutes. Rinse it out by brewing a

decanter full of cold water. Discard water.

12. Wash, rinse and dry decanter and lid.

13. You may also use a commercial cleaner made for automatic

coffeemakers.

14. When coffeemaker has cooled, wipe exterior housing with

a damp cloth.

Any servicing requiring disassembly other than the above

cleaning must be performed by an authorized service center.

Mill & Brew Assembly

Never attempt to disassemble the grinder. If you wish to empty the

mill/brew basket to refill with different beans, pour beans out, then fill

with new beans. There will always be some ground coffee remaining

in the basket.

Care and Cleaning (Continued)

Troubleshooting Guide

•If mill/brew lid is opened during brewing cycle, ON/OFF LED will

flash. To restart brewing process, reclose mill/brew lid.

•To position or remove the mill/brew assembly, press inward on the

indentations on top of the lock buttons. Open mill/brew lid and lift

up if removing, or place into position and then release lock buttons.

If basket is properly seated and locked onto the base unit, the

mill/brew and assembly will not move.

NOTES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Melitta Kaffeemaschine Handbücher

Melitta

Melitta ENJOY THERM Bedienungsanleitung

Melitta

Melitta Solo & Perfect Milk Bedienungsanleitung

Melitta

Melitta 190 Bedienungsanleitung

Melitta

Melitta LOOK THERM Bedienungsanleitung

Melitta

Melitta Mill & Brew MEMB1B, Mill & Brew MEMB1W Bedienungsanleitung

Melitta

Melitta Easy Series Bedienungsanleitung

Melitta

Melitta Wa M600 SF-Ku 200 Bedienungsanleitung

Melitta

Melitta Look Motion Bedienungsanleitung

Melitta

Melitta Excellent Therm Bedienungsanleitung

Melitta

Melitta Mill & Brew MEMB1B, Mill & Brew MEMB1W Bedienungsanleitung

Melitta

Melitta Optima Timer 1008-01 Bedienungsanleitung

Melitta

Melitta epour Bedienungsanleitung

Melitta

Melitta Single 5 Bedienungsanleitung

Melitta

Melitta Single 5 Bedienungsanleitung

Melitta

Melitta LOOK THERM Bedienungsanleitung

Melitta

Melitta CaffeO Solo&milk Bedienungsanleitung

Melitta

Melitta LOOK Selection DeLuxe 1011 Bedienungsanleitung

Melitta

Melitta cup-breakfast Bedienungsanleitung

Melitta

Melitta Cafina XT8-F Bedienungsanleitung

Melitta

Melitta Cafina XT4 Bedienungsanleitung

Melitta

Melitta Stage Therm Bedienungsanleitung

Melitta

Melitta Cafina XT4 Bedienungsanleitung

Melitta

Melitta Caffeo Solo & Milk Bedienungsanleitung

Melitta

Melitta MEFB4B Fast Brew Bedienungsanleitung

Beliebte Kaffeemaschine Handbücher anderer Marken

Taurus

Taurus Livorno 6 Bedienungsanleitung

Delta-q

Delta-q QUICK Bedienungsanleitung

Bunn

Bunn LCA-1 Fehlerbehebungshandbuch

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Montageanleitung

Saeco

Saeco Vienna Plus Sup 018M Bedienungsanleitung

DeLonghi

DeLonghi DC300 Bedienungsanleitung

INCAPTO

INCAPTO BXCO1470E Bedienungsanleitung

Bosch

Bosch TASSIMO finesse TAS16B Series Bedienungsanleitung

Exido

Exido 245-072 Bedienungsanleitung

Animo

Animo OptiVend Choco Bedienungsanleitung

Siemens

Siemens TQ505DF Series Bedienungsanleitung

DeLonghi

DeLonghi ECI341 Bedienungsanleitung

Krups

Krups KT406511 Bedienungsanleitung

Cimbali

Cimbali M32 Classic Bedienungsanleitung

Philips

Philips HL3844N Bedienungsanleitung

Bosch

Bosch TES 515 SERIES Bedienungsanleitung

Tekmatix

Tekmatix TMFM - 65 Bedienungsanleitung

Scarlett

Scarlett SC-CM33005 Bedienungsanleitung