Merg DCC-TOTI Bedienungsanleitung

8-channel DCC-TOTI Detector (DCC-TOTI)

Building Instructions. Issue 2

These are the Building Instructions for 8-channel DCC-TOTI (Train-On-Track-Indicator) Input Module (DCC-TOTI) which is used to

monitor the presence of trains on up to 8 rail sections. It is designed for easy interfacing to a CAN-ACE8C for CBUS systems. Do take a

few minutes to read right through these Instructions before commencing assembly and begin by checking through the kit contents. If

any items are missing please contact the Kitmaster. These instructions refer to Rev 1.01 of the printed circuit board (PCB).

Static Precautions are vital when handling the Integrated Circuits, which should be left in their protective tubes until

instructed to install.

Circuit Diagram

Assembly starts with the smallest items first to allow the pcb to lie flat on the bench when soldering the

underside. Do not attempt to solder the diodes on the reverse until the top components are fitted.

DCC-TOTIbuild.doc Page 1 Mar 2013

8 channel train detector module (DCC-TOTI) - Building Instructions contd

Fit the 8 1K0 Resistors (Marked 102 or 1001)

Fit the 8 1K5 Resistors (Marked 152 or 1501)

Fit the 8 4K7 Resistors (Marked 472 or 4701)

Fit the 2 22K Resistors (Marked 223 or 2202)

Fit the 16 100K Resistors (Marked 104 or 1003)

Fit the 12 100n Capacitors (Normally unmarked; may be fitted either way around)

Fit the 4u7 Capacitor (Normally unmarked; may be fitted either way around)

Fit the 8 LED's, taking care not to melt the plastic. They must be fitted with the green dot (or similar) at the

opposite end to the + symbol shown in the layout.

Fit the 8 LL4148 Diodes. These MUST be fitted with the black band in the direction shown.

At this stage, do a quick visual check that all components are correctly soldered and there are no bridges

between tracks.

Fit the 4 LM339SM integrated circuits with the 'notch' on one end of the chip corresponding to the layout.

Fit the 2 ACPL-247-500 optocouplers with the 'notch' on one end of the chip corresponding to the layout.

These are best fitted by solding two legs at opposite corners, checking for correct registration, then soldering

the remaining pins, being careful to not cause any solder bridges between the pins.

Fit the 9 B340 Diodes. These MUST be fitted with the white band in the direction shown.

At this point, fit the 8 B340 diodes on the bottom of the board. These should be fitted with the white band

towards the adjacent connector.

Again, do a quick visual check that all components are correctly soldered and there are no bridges between

tracks.

Now assemble and fit J1.

Check the PCB looks similar to these photographs:

Fit J2 unless a direct connection to a CAN-ACE8C is used (see below)

DCC-TOTIbuild.doc Page 2 Mar 2013

8 channel train detector module (DCC-TOTI) - Building Instructions contd

Testing

Connect the DCC-TOTI to DCC tracks as shown below. Note that one side of the tracks MUST be common.

The polarity of the DCC feed is unimportant.

Do not connect anything to J2 at this stage.

Power up the system and check that none of the LED's are lit.

Connect a voltmeter across C14 and check for around 12V – though note that this voltage will vary

depending on the peak voltage of the DCC feed used. Check that the voltage on R5 and R6 is approximately

6V, or half of the voltage across C14.

Put a train on each track in turn, and check that the appropriate LED is illuminated.

A damp finger across the tracks can also be used for testing.

Check that the LED isn't illuminated when the train is removed.

Connect J2 to the input module and repeat the tests, checking that each input is correctly asserted when a

train is on each track.

Direct Connection to CAN-ACE8C

The DCC-TOTI board has been designed for direct connection to a CAN-ACE8C board. To do this,

don't fit terminal blocks to J2 on the CAN-ACE8C or to J2 on the DCC-TOTI, but instead use a 10 way right

angle 0.1” header, suitably bent, to link J2 on the DCC-TOTI board to the 0.1” holes by J2 on the CAN-

ACE8C.

DCC-TOTIbuild.doc Page 3 Mar 2013

8 channel train detector module (DCC-TOTI) - Building Instructions contd

Kit Contents

Note that TS4148 diodes can be used instead of LL4148. These are in a rectangular package and

are much easier to fit. The Rapid part number for these is 47-1004.

4 Channel Option

If less tracks need to be monitored, build the 4 channel version. This uses the same PCB but only

fit the components shown below:

If the 4 channel option is used with a CAN-ACE8C board, inputs 1..4 are still available.

DCC-TOTIbuild.doc Page 4 Mar 2013

Component Value Description Qty Parts Supplier Part Number

10PinCon Molex 1 J2 Rapid 22-0850 /22-0832

B340 ShtkyDiode 17 Farnell 1456529

Candem11way Terminal Strip 1 J1 Rapid 3*21-3001 + 1 *21-3000

CP-SM 4u7 Ceramic Cap 1 C14 Rapid 71-0516

CP-SM 100N Ceramic Cap 12 C1-C13 Rapid 71-2024

LED_SM LEDRED LED0805 8 L1-L8 Rapid 72-8558

LL4148 Silicon Diode 8 D3,6,9,12,14,16,20,22 Rapid 47-2386

LM339SM QuadComparator 4 U1-U4 Rapid 82-0244

ACPL-247-500 Opto Coupler 2 U5, U6 Farnell 163-4758

R-SM 1K0 Resistor 8 R1,8,13,20,17,2833,38 Rapid 72-0217

R-SM 1K5 Resistor 8 R7,12,19,24,27,32,37,42 Rapid 72-0227

R-SM 4K7 Resistor 8 R3,10,15,22,25,30,35,40 Rapid 72-0257

R-SM 22K0 Resistor 2 R5,6 Rapid 72-0297

R-SM 100K0 Resistor 16 Rapid 72-0337

PCB 1 MERG 968

R2,4,9,11,14,16,21,23

R18,26,29,31,34,36,39,41

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung