MERLYN 6 Series Bedienungsanleitung

Thank you for choosing Merlyn.Please familiarise yourself

with the fitting instructions before commencing fitting.

1. Check that you have the tools required.

2 that the installation site is compatible . Check

with size of door supplied

3. Check all the enclosure components.

4 that the installation kit is complete. Check

DO NOT attempt to install the product unless you can

tick ALL 4 boxes as satisfactory.

The wall plugs supplied with the installation kit are for

use in solid walls. Hollow or 'stud-partition’ walls will

require alternative fixings. Please consult a hardware

supplier for the correct type.

It may also be necessary to consult your tiling supplier

about the correct method for drilling your tiles.

VIVID

IMPORTANT

Any parts missing or damaged must be reported to your supplier within 5 days of purchase.

Inspect shower enclosure before fitting .

No claims will be acceptable after product has been installed.

USE SAFETY EYEWEAR WHEN DRILLING

2 DOOR QUADRANT

INSTALLATION GUIDE

2 DOOR QUADRANT

M036-00

COMPONENTS AND BOX CONTENTS 1

Handle

Bottom roller

Screw cover cap

Upright water seal for fixed panel

Cover cap for wall profile

∅6 30 wall plug×

Screw cover cap clip

Wall profile

Cover cap for upright profile L/R

DescriptionNo. QTY Description QTY

Part No. No. Part No.

B head screw ST4×30

Note: Further part details for fixing kit available on page 2

Flat head screw ×ST4 12 6

V4111

V4110

V6113

V2114

V2115

Flat fixed panel

Upright water seal for moving panel

Moving panel

17 Glass clip screw

18 Roller stop

Roller cover cap

Rail

S6LC8433

S6LC83291871 C

V4101

Roller stop screw

1 0

1 1

1 2 1 3 1 4

1 6

1 7

1 82 2 2 1

1 5

Bottom seal

1 92 0

Glass clip

Top roller

V2101L/R

V2104

S6S01

V3211

V6106L/R

S6HDLE

V6105

V2109

V4109

S6LL8059

S6LL8060

Tools Required

- 6mm masonry drill bit

- Power drill

- Quality Silicone

- Pencil

- Tape Measure

- #2 Philips Head screw driver

- Spirit level with horizontal and vertical level indicators

IMPORTANT - Installation site

1. Ensure the top surface of the shower tray on which the enclosure will be installed is level in every direction.

2. The tiles or other wall finishing should be effectively sealed at the tray edges.

3. Tiles should extend at least to the corners of the tray and a minimum of 2.0 metres from the top of the tray.

Spanner

FIXING KIT COMPONENTS, TOOLS REQUIRED, SITE 2

V2101L

1×

V2101R

1×

V2104

×2

S6HDLE

2×

S6HDLEP2 2×

S6HDLEP3 4×

S6HDLEP4 4×

S6HDLEP1 2×

S6LL8059

4×

S6LL8060

4×

V2115

12×

V2114

12×

V6113

×6

V4111

×14

V4110

×6

V6115

× 1

S6HDLEP6 4×

S6HDLEP7 1×

S6HDLEP5 8×

FITTING WALL PROFILE 3

Step 1.

Step in wall profile 20mm from the front edge of the shower tray. Ensure wall profile is plumb

Do not silicone behind wall profile to wall, see sealing section.

Step 2.

Mark the position for fixing the wall profile to wall.

100％

Lev el !

TRAY MUST BE 100% LEVEL IN ALL DIRECTIONS

Ensure the shower tray is level in all directions and is

properly sealed to the wall. The wall must be tiled down to

the top edge of the tray. Do not angle out bottom tile.

TRAY MUST BE SEALED FULLY AROUND WHERE THE

TRAY MEETS THE WALL.

PROCEDURE

20mm

V6113

Inside

∅6mm masonay

drill bit

V4111

V2114 Inside

S6S01

FITTING RAILS 4

Step 4.

Place fixed panel gasket onto bottom edge of glass.

Then fix the two fixed panels and upright profiles to

the bottom rail, using V4111 screw.

Step 5.

Fit the wall profiles to the assembled

frame.

V4111

Step 3.

Loosen fixed glass

panel clip.

Do not remove the

screw.

Step 6.

Tighten fixed glass

panel clip.

V3211

seal (flush with

glass edge)

U shape

V3211 U shape

seal (flush with

glass edge)

FITTING DOOR PANELS AND ROLLERS 5

Step 7.

Position the assembled frame onto the

tray and into the wall profile.

In a situation where you are close

to the minimum adjustment, fit only 1 wall

profile to the wall and put the second wall

profile into the frame, position the frame

onto the tray and then fix the second wall

profile to the wall.

NOTE:

Moving panel

Step 8.

Assemble the top rollers using

spanner.

Step 9.

Assemble the bottom rollers using

Bottom rollers has

spring for easy clear function.

screw driver

Important:

Top roller

Ensure the rollers are fitted in the

correct position.

Bottom roller

Outside

Bottom

roller

Bottom

rail

S6LC8433

(shorter seal)

S6LC83291871

(longer seal)

Outside

Step 10.

Hang the moving panel to the

top rail, then push the bottom

rollers to bottom rail.

Step 13.

If the moving panels are not closing correctly, or there

is any gap between the magnets,

loosen the screw on the top roller to adjust them.

Note: Adjust top rollers also to ensure bottom rollers

are running properly in the bottom track.

FINISHING

Inside

Top roller

Top rail

push

down

Ensure the top rail is level

then go on to step 12

V2101L/R

V2104

V6115

V4110

V2114

Top roller

Inside

S6HDLEP7

S6HDLEP6

S6HDLEP1

S6HDLEP3

S6HDLEP4

S6HDLEP2

S6HDLEP5

V2115

Step 12.

Drill through upright and wall profile

in 3 places, top to bottom as shown.

SEALING AND TROUBLE SHOOTING

DO NOT use

the

enclosure

for 24 hrs

TROUBLE SHOOTING GUIDE

Step 16.

Use a quality silicone sealant

and applicator gun to seal the

finished door.

Seal top to bottom on the

between the wall

profile and the wall.

Do not apply sealant on

the inside of the tray.

Seal only along bottom on the

between

glass/rail/profile and the tray

and approx 50mm up

between the wall profile and

the wall. Seal at vertical

joints on bottom of frame on

outside only.

SEALING INSIDE

INSIDE

Note:

SEALING OUTSIDE

OUTSIDE

DOOR NOT ALIGNING

1. Is the tray 100% level? ( )

2. Have the walls been checked at different levels to ensure consistency?

3. Are the wall profiles stepped in 20mm from the edge of the tray? ( )

4. Do the finished tile measurements on the tray comply with the adjustment listed on the

label and in the specifications book?

6. Is the top rail level? ( )

DOOR LEAKING

2.Is the upright seal fitted? ( )

3.Is the door sealed correctly? ( )

see page 3

see step 1

see

see step 12

See step 13

see step 15

see step 16

---

Are the rollers adjusted so the bottom rollers are running and not rattling in the

bottom track.( )--- step 10,13

1.Have the rollers been adjusted so there is no gap between the magnets. ( )

50mm

Andere Handbücher für 6 Series

Dieses Handbuch passt für folgende Modelle

Andere MERLYN Badezimmerarmatur Handbücher

MERLYN

MERLYN 6 Series Bedienungsanleitung

MERLYN

MERLYN 6 Series Bedienungsanleitung

MERLYN

MERLYN MB11 Bedienungsanleitung

MERLYN

MERLYN NEXA VWBSVL300 Bedienungsanleitung

MERLYN

MERLYN 8 Series Bedienungsanleitung

MERLYN

MERLYN IONIC EXPRESS Bedienungsanleitung

MERLYN

MERLYN ARYSTO Bedienungsanleitung

MERLYN

MERLYN NEXA VWBSVL300 Bedienungsanleitung

MERLYN

MERLYN IQ Nexa Bedienungsanleitung

MERLYN

MERLYN SIDE PANEL Bedienungsanleitung

MERLYN

MERLYN MB3B Bedienungsanleitung

MERLYN

MERLYN ARYSTO Bedienungsanleitung

MERLYN

MERLYN Arysto GHH900HL Bedienungsanleitung

MERLYN

MERLYN 8 Series Bedienungsanleitung

MERLYN

MERLYN Arysto Ten GMW100 Bedienungsanleitung

MERLYN

MERLYN 6 Series Bedienungsanleitung

MERLYN

MERLYN 6 Series Bedienungsanleitung

MERLYN

MERLYN 6 Series Bedienungsanleitung

MERLYN

MERLYN MB2 Bedienungsanleitung

MERLYN

MERLYN EASY CORNER DOOR Bedienungsanleitung

MERLYN

MERLYN 8 Series Bedienungsanleitung

MERLYN

MERLYN MB7 Bedienungsanleitung

MERLYN

MERLYN MB12 Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

Kohler

Kohler K-13056 Montageanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

baliv

baliv DUK-80.30 T Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung